similar to: TDM400P GroundStart Problems

I am having a problem with Red Alarms on X100P cards. The most frustrating thing is I can not duplicate the alarms, therefore am not sure how to solve it. I have read after searching posts and the web that you can try different signaling methods which may help alleviate the problem. There is fxsks (Which I am currently using), fxsgs, and fxsls While reading the Digium site about these different

Hello I have installed my new E100P card in the same machin with two TDM04B cards. I have followthe instructions on http://www.digium.com/index.php?menu=configuration#T_E100P_PRI This is my zapata.conf span=1,0,0,cas,ami fxsls=1-15,17-31 dchan=16 fxsks=32-39 loadzone = us defaultzone=us I do *modprobe zaptel wct1xxp wcfxs ans seems to work ok. * But when i do ztcfg -vvv i got Zaptel

Em (20:59:21), Asterisk Users Mailing List - Non-Commercial Discussion escreveu: >On Tue, Jun 21, 2005 at 08:09:52PM -0300, Alessandro wrote: >> >> Does Somebody know why no load modules to FXS? I used zaptel-1.0.7 >> version. > >What color are the modules? >Post your /etc/zaptel.conf > >-- >Mike Mike, The color is green, red ans bluw. Link

Callerid issue 1) if you run ztmonitor on the fxo line & call in do you hear the fsk tone if yes then we beleive the CAC is passing fsk 2) in chan_zap->ss_thread around line 4154 (current cvs) if you get to the callerid_feed at least once then if you get to chan_zap->ss_thread->callerid_get around line 4163 (current cvs) does this parse fail

After speaking with several people, and even participating in a forum of several other people with echo issues, I thought I'd share what we've done (well actually what our chief R&D engineer, Brett Bourn has done...) First let me say that normal cheapy PC hardware couldn't be made to function with out echo. We tried on both the single port Digium T1 card and the 4 port Digium T1

zaptel compiles fine (make linux26) but when I modprobe ztdummy I get the follow error. [root@localhost zaptel]# modprobe ztdummy Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected FATAL: Error running install command for ztdummy System info: Linux localhost.localdomain 2.6.9-5.0.5.ELsmp #1 SMP Thu May 19 19:24:44

Hi all, Does somebody know why no load modules to FXS? I used zaptel-1.0.7 version driver. [root@server1 zaptel-1.0.7]# modprobe wctdm ZT_CHANCONFIG failed on channel 3: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? /lib/modules/2.4.21-27.EL/misc/wcfxs.o: post-install wcfxs failed

Hi All I have problem with LIBMFCR2 for once Exchange I using Sangoma card, the firstly. my ssystem run successful with MFCR2, connected to E10 (Acatel Exchange), after that, i move connection connect to EWSD (Siemens), my system don't work. error protocol R2. my system: Asterisk CVS 1.1.X LibMFCR2 pre.005 and unicall-pre.005 this's my setting and my setting wanpipe1.conf

Hello, is there a full guide to what kewlstart is supposed to do with FXO or FXS lines ? is it only applicable to one of the interfaces FXO -or- FXS but not both ? I asked earlier if FXS lines can be made to reverse polarity, and someone else pointed out that the chipset on the FXS ports seems to support it, perhaps the driver in the asterisk zaptel interface module needs to be modified to support

Hello Astrites, I was just about to send out a long email about not being able to detect hang-up with my CAC II FXO module on my PSTN POTS lines. I had tried many configurations. I had attached a toner to the line to see if I was getting this "disconnect supervision" signal after hang-up. (toner has a line powered light in the off position) It seemed that I was getting the signal,

hello, I just installed 2 brand new x100p cards into my linux system. Everything compliled and worked fine from the first try. Hoewver the phone lines I will use with this system have groundstart signaling. I have tried to change the zaptel.conf and zapata.conf to use this type of signaling but ztcfg gives me an error every time with the new configuration. Bellow are the config files and the

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

Hi again, I'm trying to setup our non pri T1 (they call it a Long Distance T1), our current pbx has the signaling set to E&M, I can set em in zapata.conf, but I'm trying to track down the proper entries for the zaptel.conf file. The digium docs only show a PRI example. Our current system has these settings: Signalling: E&M Framing mode: ESF Line Coding: B8SZ here's my

Simple question that google hasn't helped much with (likely poor search terms) I just installed a Sangoma A200 with overall good results. Initial tests with both incoming and outgoing calls were very positive. Until I made a normal call that lasted more than 30 seconds. I setup the FXO with kewlstart signalling, and the outgoing call is never registered as 'Answered' and the dial

Hi everyone, I've just got my X100P card installed and working but there seems to be an issue with hang-up supervision. If I stuff a call out over the X100P card onto the PSTN that's fine. When I hang up the SIP phone the PSTN call ends. If I receive a call from the PSTN, it's answered and everything is ok until the remote party hangs up. Asterisk thinks the call is still active and

Hi there! I'm setting up a connection between Asterisk ver. 1.2.13 and a Harris 20-20 PBX. More less everything went fine, but the problem I have now is when dialing to the Harris PBX, it seems to pick up my call as soon as it reaches it. For example if from the Asterisk outgoing folder I dial an extension, say 100, and play a prompt as soon as it is picked up, the promt is beign played as

Hi All, I recently purchased the Asterisk Developer's Kit (TDM) to try out Asterisk. After following the directions in the Digium's FAQ topic entitled "Q. How do I configure my TDM40B and X100P?", I'm receiving the following error: WARNING[1074428608]: File chan_zap.c, Line 6748 (load_module): Ignoring rxwink ERROR[1074428608]: File chan_zap.c, Line 6692 (load_module):

Hello, I am trying the setup the TDM01B card. 1 FXO. I connected it to a regular home line. in the /etc/zaptel.conf, I have fxsls=4 In the /etc/asterisk/zapata.conf I have: signaling=fxs_ls language=en group=1 context=default channel => 4 When I start asterisk, I get this error: ERROR[10376]: chan_zap.c:6584 mkintf; Signaling requested on channel 4 is FXO Loopstart but line is in FXS

Hi there, I have a cablemodem, ARRIS brand, model tm502G. It has two FXS ports. I was wondering if anyone has details about the correct signalling of these FXS ports when connected to original X100p. Tests: fxsks on the zapata.conf and zaptel.conf files. From my cellphone I call the ARRIS, it starts ringing but the zap channel sees no call coming in. fxsls on the zapata.conf and zaptel.conf

Hi, I'm trying to configure a clone of X100 for use with asterisk, but i have reached the zaptel.conf step and have not been able to progress further as i'm getting the following error: arnor:~# ztcfg -v Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: Invalid