similar to: Accessing ISDN with avm bluetooth hardware

I have an asterisk installation connected to 2 isdn lines via an AVM C2 card. modules seems to load well, lsmod gives : c4 19588 4 b1 24192 1 c4 capidrv 28468 2 isdn 134604 9 capidrv slhc 7552 1 isdn capi 18112 4 capifs 6024 2 capi kernelcapi 46112 4

Hi, I installed CentOS 3.3 and kept the machine up2date. I installed poptop and the newest ppp-cvs version ( ppp-2.4.3-0.cvs_20040527.6) We are running a ssh + ppp tunnel for our internet tunnel/tunnel to our NOC. After the upgrade we see these error messages while starting the tunnel: Jan 24 15:00:40 natgw modprobe: modprobe: Can't locate module ppp-compress-26 Jan 24 15:00:40 natgw

Hello all, I'm trying to setup a AVM C2 card. I have read the kernel requirements for this card. <M> CAPI2.0 support [*] Verbose reason code reporting (Kernel size +=7K) [*] CAPI2.0 Middleware support (EXPERIMENTAL) <M> CAPI2.0 /dev/capi support [*] CAPI2.0 filesystem support <M> CAPI2.0 capidrv interface support My problem is when I make a "make

I own a ME600 EPIA Mini-ITX main board with the latest Debian distro (kernel 2.6.8) with isdnutils-base, libcapi20-dev, libcapi20-2, isdnactivecards installed. I have a QuadBRI module by Junghanns with bristuff-0.2.0-RC3a (with asterisk-1.0.3, zaptel-1.0.3 and libpri-1.0.3), and chan_capi-0.3.5. I followed all INSTALL instructions, but I have some strange behaviour. All modules seems to be

Hi, i will use an AVM C2 controller with asterisk. How can i use both card ports ?? On the voip-info.org Wiki is only notice to: You will need a section for each controller in /etc/asterisk/capi.conf so the C2 will have 2 sections. But how is look like this ? Only on the first port is asterisk assume connections, but nothing on the second card port. In the dmesg is only the capidrv-1 shown,

Hello all, I just got the latest cvs snapshot and I'm trying to compile asterisk.. When I run nefeli:/usr/src/asterisk/zaptel# make clean; make linux26 Compile stops with errors... /usr/src/asterisk/zaptel/zaptel.c:6509: warning: passing argument 2 of 'class_device_create' makes pointer from integer without a cast /usr/src/asterisk/zaptel/zaptel.c:6509: warning: passing argument 3

I'm using avm fritz card usb with kernel 2.6 patch with mISDN. The module is load correctly when I type lsmod I've got the following output: Module Size Used by zaptel 178308 0 avmfritz 21388 0 mISDN_isac 14336 1 avmfritz mISDN_dsp 191424 0 l3udss1 34184 0 mISDN_l2 39040 0

Hi Recently I upgraded my kernel to 2.6.11 (debian) and applied some patches from pom-ng (netfilter) and the iproute2-ss050330 package I have been experiencing a lot of crashes in the kernel (snip below) ================================== Apr 5 20:00:21 sydlxfw01 kernel: Unable to handle kernel NULL pointer dereference at virtual address 00000221 Apr 5 20:00:21 sydlxfw01 kernel: printing eip:

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Hi all, * was running ... I have a WT405P and an AVM C4 with chan_capi 0.3.4a Today chan_capi stopped working, without any changings at the system. It seems, that not * is the reason, because isdn-log also shows no calls. If I try to call * from outside via capi, I only get a busy. That is the try from inside to outside: stern01*CLI> -- data = @89930:0107901723168212 -- capi

Hello, I acquired a Diva Server 4BRI for an AsteriskPBX system and installed a 2.4.20 kernel modified with the latest eicon capi2.0 support from www.melware.net. Capi support seems to work fine: Asterisk+chan_capi answers the calls. However if I try to use my old isdnutils apps by loading a i4l compatibility layer then I have the following problems: - if I use the diva2i4l module and start the

Hi, I added a Fritz!PCI card to my asterisk system which is running on fc2 !. I installed the avm modules (fcpci) and when i try an capiinit and a capiinfo then everything seems to be OK (you can see capiinfo and lsmod at the end of the text) !. I installed the asterisk chan_capi module and when i start asterisk and enter the command capi info on the command line i get back: *CLI> capi info

Hi all, does anyone have capiECT working? I can't get it to work - please see my logfiles below. While using an * CVS version of late September and chan_capi-0.2.5 (I guess), it worked!!! (I know, never change a running system ... should've backuped ... etc.) Here's the setup: NT----AgfeoISDNPBX----AgfeoISDNPBX----AnalogPhones in between the two PBX I attached my * server with a

Hi, I am trying to configure a Diva Server 4BRI to work with chan_capi. Here are the steps that I took: - compiled fresh kernel with new-style CAPI support: i4l_divas_1.2 - got the divactrl_1.2 utilities, configured the card startup scripts, - rebooted, card firmware loaded properly, "capiinfo" displays detailed info on 4 controllers, however there is an error message: FAC REQ -

hi guys... im a new asterisk user. i dont understand why asterisk doesnt start. pls take a look at the output below. i could start it a couple of times .. #asterisk -gc Asterisk CVS-v1-0-01/21/05-14:58:31, Copyright (C) 1999-2004 Digium. Written by Mark Spencer <markster@digium.com> ========================================================================= [ Booting....................Jan

Hi Jon, perfect instructions, thank you very much. I used them and after some tests they worked. Here is what I did. Maybe someone could use it completely: ------------------------------------------------------------ Install helpers: apt-get install kernel-package ncurses-dev fakeroot wget bzip2 Go to usr directory: cd /usr/src wget

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hi, I successfully installed 2 avm card in my asterisk box but I'm unable to make call. My capi.conf is: msn=0721111,07211115 incomingmsn=* controller=1,2 softdtmf=1 context=default echocancel=yes callgroup=1 devices=2,2 my capi info : Contr1: 2 B channels total, 2 B channels free. Contr2: 2 B channels total, 2 B channels free. my extensions.conf : exten =>

I hope this EIP can enlightend the developers: Jun 10 10:28:59 shawarma kernel: Unable to handle kernel NULL pointer dereference at virtual address 00000019 Jun 10 10:28:59 shawarma kernel: printing eip: Jun 10 10:28:59 shawarma kernel: c0181d47 Jun 10 10:28:59 shawarma kernel: *pde = 00000000 Jun 10 10:28:59 shawarma kernel: Oops: 0000 [#1] Jun 10 10:28:59 shawarma kernel: Modules linked in: