similar to: Hang-up Supervision (UK)

Callerid issue 1) if you run ztmonitor on the fxo line & call in do you hear the fsk tone if yes then we beleive the CAC is passing fsk 2) in chan_zap->ss_thread around line 4154 (current cvs) if you get to the callerid_feed at least once then if you get to chan_zap->ss_thread->callerid_get around line 4163 (current cvs) does this parse fail

Hello Astrites, I was just about to send out a long email about not being able to detect hang-up with my CAC II FXO module on my PSTN POTS lines. I had tried many configurations. I had attached a toner to the line to see if I was getting this "disconnect supervision" signal after hang-up. (toner has a line powered light in the off position) It seemed that I was getting the signal,

Simple question that google hasn't helped much with (likely poor search terms) I just installed a Sangoma A200 with overall good results. Initial tests with both incoming and outgoing calls were very positive. Until I made a normal call that lasted more than 30 seconds. I setup the FXO with kewlstart signalling, and the outgoing call is never registered as 'Answered' and the dial

Hi there! I'm setting up a connection between Asterisk ver. 1.2.13 and a Harris 20-20 PBX. More less everything went fine, but the problem I have now is when dialing to the Harris PBX, it seems to pick up my call as soon as it reaches it. For example if from the Asterisk outgoing folder I dial an extension, say 100, and play a prompt as soon as it is picked up, the promt is beign played as

*** Now you just need a "phone" or "station" (FXS) device and a method of connecting it. *** So... essentially I need to spend another $125 US on a Wildcard TDM400P so I can plug in an analog phone? On the X100P description it says: "The X100P supports FXS Loopstart and "Kewlstart" (Loopstart with far end disconnection supervision). It can detect ringing and

Can anyone help me with the term that SBC uses to refer to disconnect supervision? I have an Adit 600 channel bank which has helped improve the disconnect detection time down to about 8 seconds. This is still causing some issues in particular with call progress enabled in * we are having a few disconnects while calls are in session (about 2 reported in first 5 days of use). I have talked both to

Hello, is there a full guide to what kewlstart is supposed to do with FXO or FXS lines ? is it only applicable to one of the interfaces FXO -or- FXS but not both ? I asked earlier if FXS lines can be made to reverse polarity, and someone else pointed out that the chipset on the FXS ports seems to support it, perhaps the driver in the asterisk zaptel interface module needs to be modified to support

Hello, I am having problems configuring a TDM400P 4 Port FXO card with groundstart signalling. The box has 2 X100P's, 1 TDM04B and 1 TDM40B. I can configure it for loopstart and it works, just not groundstart, which I need for this installation. What am I missing? Thanks! Mark /etc/zaptel.conf #two X100P FXO Cards # fxsls=1-2 # TDM400P 4 Port FXO (TDM04B) fxsgs=3-6 # TDM400P 4 Port

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

I need to know how to setup the data side of the T1 on my Linux Box. I have found information about configuring a PRI and HDLC but nothing about the Frame-Relay type setup for data. The following is information from our T1 provider. Network T1: Framing = ESF Line code = B8ZS Build out = 0-133ft(DSX)/0dB(CSU) Clock = network Pulse-density-enforce = off alarm-option = on alarm-delay = 15

Hello All, I've mostly solved my DID problem from a few days ago. Apparenly the lines weren't configured properly. Now heres the next question. 12 E&M wink lines from telco. I have them all plugging into an Adtran 750 with FXS cards. The Adtran ports are configured DPO. How do I signal this from Zaptel. I have them setup E&M in zaptel.conf and EM_W in zapata.conf. They

Can anyone help me with the term that SBC uses to refer to disconnect supervision? I have an Adit 600 channel bank which has helped improve the disconnect detection time down to about 8 seconds. This is still causing some issues in particular with call progress on we are having a few disconnects while calls are in session. I have talked both to some local phone contractors and SBC directly and

Ok so this is officially driving me crazy. I have an Asterisk 1.6.1.6 install with DAHDI/DAHDI tools (latest) and an OpenVOX TDM400 card with 1 FXO port and 1 FXS port. I have a POTS line from my phone company attached to the POTS line. I have asked for "disconnect supervision" to be provisioned on my line and they claim to have added it. However, my scenario is as follows: I receive a

Hi everyone (Mark, Jim). I am new to the list but thanks to both Mark and Jim, I have being using "asterisk" since summer 2001. I am just updating my version that was a year old. Yes, I know, I got busy with other things like paying bills so I don't have to sleep with the dog anymore. Anyway, one of the frustrations I have been dealing with (keep in mind that my version of

Hi, all I have installed TDM400 with 1 FXS and 1 FXP ports. Now I am goig through documentation on how to configure it. It mentions 3 protocols: Loopstart, Groundstart and Koolstart. Which one do I use? Can someone send me sample zaptel.conf file for Australia? This will save me some time and will be used as a working example. Thanks, Rudolf

I have two loop-start phone lines connected to an Adtran TA 750 channel bank. When a call comes into asterisk thru the first phone line and the call is redirect (in transit) back thru the second phone line, the channel bank will leave one or both lines opened (ie hangup with spawn a connection again). does any body have a suggestion: 1) I checked the cables into the channel bank from both phone

Is anyone on the list using an Audiocodes gateway with asterisk and SIP? I'm looking at that platform, but I have a couple of issues: 1) Echo cancellation. The echo that I'm hearing with an X100P is unacceptable. Does the Audiocodes do better? 2) Line signalling. I'm using Kewlstart with the X100P, but it looks like the audiocodes uses loopstart only. How does this work with

Hello, I am trying the setup the TDM01B card. 1 FXO. I connected it to a regular home line. in the /etc/zaptel.conf, I have fxsls=4 In the /etc/asterisk/zapata.conf I have: signaling=fxs_ls language=en group=1 context=default channel => 4 When I start asterisk, I get this error: ERROR[10376]: chan_zap.c:6584 mkintf; Signaling requested on channel 4 is FXO Loopstart but line is in FXS

Hi, I have a TrixBox install with a Sangoma A200 and 4 FXO ports, there are 3 BT lines connected directly to these ports. One of the lines has BT FeatureLine Compact and this is the line I am having problems with, the other 2 lines are working perfectly, detecting CID, answering incoming calls and placing external calls via SIP devices. I am receiving a error log entry: chan_zap.c:

Hi.. I've got an asterisk setup with an X100P card installed.. I'm noticing that upon hangup, it takes a good 3 to 5 seconds before asterisk realizes the line has been hung up and drops the call.. this causes my SIP phone to continue ringing, and occassional phantom voice mail messages to be left.. I'm located in good old standard North America, with a regular Verizon residential