similar to: E100P R2 signaling

Hullo everyone, Iam new to Asterix but am trying to get R2 signalling working with a Digium E100P E1/PRA Card. My Telecom doesn't have an implementation of ISDN PRI yet, so it's R2 that is supported. Could anyone have a patch to fix this for me. Am told it has something to do with Assembly Language programming. Please help me fix this. Regards, Nicholas

Has anyone found a solution for asterisk and r2 signaling ? Steve Underwood had given some information saying he had a working asterisk working. I need it to work with Argentina R2 signaling Sam -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040915/3289f694/attachment.htm

Hi, I'm installing my first E100P. My zaptel reads the following: Span=1,0,0,ccs,hdb3,crc4 E&m=1-31 My Zapata.conf reads the following: Signaling = em_w Channel =1-15 Channel =16-31 After starting the zapter service I get: ZT_SPANCONFIG failed on span 1: No such device or address (6) ??? PauloHM -------------- next part -------------- An HTML attachment was scrubbed...

Hey all! I had an experience trying to set up an E1 in Brazil which could help somebody. In Brazil is very common telcos to have just R2 digital as their primary signaling. As I were trying to set up an E100P, which does not support R2 yet, I had to test an other signaling which works perfectly with Asterisk. They call this signaling as RDSI, using ccs as framing and PA (primary access) as

Hello Folks, I'm trying to decide here between a few cards for connecting an Asterisk box to a single E1 channel (either PRI or R2 signaling): - Digium E100P: has been replaced by the TE110P below, but can still be had at places like digitnetworks.com for $475, and I guess there's always a place for good-olde-obsolete cards in the world as long as they work :-) - Digium TE110P:

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

hi All, quit new to asterisk, can anybody tell me whether Wildcard E400P and Wildcard E100P support R2 CAS protocol. if they do, what is the value, i should set to 'signalling' parameter in the zapata.conf file? Surajee -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, I have an E100P, and in the zaptel.conf I have: span=1,1,0,ccs,hdb4,crc4,yellow fxsks=1-10 the light on the card is green( BTW what do all those states of the card that zttool reports YELLO, RED, BLUE ..., is there a doc for zttool?, or for the card?) in the asterisks` zapata.conf I have: [channels] context=default switchtype=euroisdn signalling=fxs_ks usecallerid=yes hidecallerid=no

hello, I have been searching the mailing list for info on R2 signalling support in * The best I came up with was a post by Steve as far back as 18 Jul 2003. This post indicates that some work was being done on it. Has anyone got any info if the current cvs does have support for R2 on E100P as yet? Thank you. Anthony

Just cross pairs 1-2 and 4-5 1 <--> 4 2 <--> 5 Never done an E1, but I think it's the same for a T1 4 wire cable. Tim Thompson Commercial Sales Engineer http://www.amatechtel.com (806) 722-2227 -----Original Message----- From: bam [mailto:bam@cqm.co.uk] Sent: Monday, December 29, 2003 9:12 AM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] E100P pinouts

Hello ml, i need some help on my zaptel configuration. My E100P only shows some YELLOW / RED alarm when I load the wct1xxp module and do a cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS YELLOW RED ... .. . My /etc/zaptel.conf is: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=nl defaultzone=nl I tried zaptel-1.0RC2 and the latest CVS

hi see below's conversation. it seems the e100p card doesn't work with BT. Any idea how this'll work against Telenor (norway)? roy <RoyK> does anyone know if I can trust the E100P to do full PRI stuff in .no? <cypromis> dunno about no <cypromis> I cannot use it in UK <cypromis> cause the framer has problems with system-x switches at bt

Hello, I have a E100P card from digium and I try to implement a conference bridge in asterisk. I wonder since I got the E100P card do I still need to load ztdummy for caller from h323 endpoints to work with Meetme? I load the E100P driver but i did not load the ztdummy driver. My h323 caller does not hear any voice play by Meetme. Looks like ztdummy is required as long as h323 is concern and

Hi, i just received an E100P, this is the first one I have ever seen, and notice that the board reads T100P. Is this right ? The antistatic bag had a small label that has E100P written on it, and the card is a bit different than the T100P I already have, Does Digium use the same boards for both cards ? I don't have an E1 link here, can I test the card just by loading the driver and run

Hello list , I?m putting to work a new asterisk box. I?m running * 1.0.3 with (one ) Wildcard TDM ( 2FXS* 2FXO) and (one) E-100P. Both boards are working well. ztcfg don?t show me any error. zttool list both cards as "OK" But when i run asterisk on verbose mode i get those errors : [chan_zap.so] => (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found --

Hello list, i've got some problems getting a E1 line with a E100P up and running (germany). # cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS/CRC4 YELLOW RED "YELLOW RED" sounds not so good. When launching asterisk, enabling pri debug on that span, i see outgoing attempts: ;---------- snip -------- > [00 01 7f ] > Unnumbered

Hi ! I am trying to configure two E100P cards, but I am a bit confused with zapta.conf in what I am trying to achieve. The * will be connected to a pstn switch with two E1 PRI lines. The E1 lines will be used for incoming calls as well as outgoing calls. My problem now is what to put in zapta.conf, I would like to group all channels from both cards together (if that's possible). Does this

All, I'd like to buy an E100P Wildcard frm Digium, but i prefer to buy it in Europe (costs, ...). Could somebody point me to an european reseller ? Thanks in advance. -- Nicolas Cartron nc@ncartron.org

Dear fellows, I need to use Asterisk with an E1 card with CAS R2 signalling for Argentina. I know that the E100P don't support it right now. Does anybody developing R2 drivers? Any other alternatives/prices to handle an E1 R2 on Asterisk? Thanks in advance!. Best regards, Pablo.

Hi, I have two E100P boards connected to my PC. I wish to setup two E1-ISDN-PRI lines, the first SPAN with 15 channels and the second one with 30 channels. When I try to load zaptel modules, I get an error message: "Loading zaptel framework: Loading zaptel hardware modules: wct1xxp wcusb Running ztcfg: ZT_CHANCONFIG failed on channel 63: No such device" Follows my zaptel.conf: