similar to: 2 Avm fritz passive card in the same box

Hi all, I'm new to asterisk and not too knowledgeable on ISDN, so please be gentle :) I have a dual-channel Eicon Diehl Diva card in a Debian Woody box with kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway ISDN line. I'm pretty certain the card and line both work since they've been used in this machine for PPP before this (but with an older kernel with DoV

Hi all, * was running ... I have a WT405P and an AVM C4 with chan_capi 0.3.4a Today chan_capi stopped working, without any changings at the system. It seems, that not * is the reason, because isdn-log also shows no calls. If I try to call * from outside via capi, I only get a busy. That is the try from inside to outside: stern01*CLI> -- data = @89930:0107901723168212 -- capi

Hi Everyone, Long time reader, first time poster. FINALLY got my First AVM Fritz Card up and running under Centos 3.4 Installed the second....modified the drivers etc as per the instructions found at the wiki System boots Modprobe capi all good modprobe fcpci all good modprobe f2pci the kernel then goes into Panic If Modprobe f2pci before fcpci the kernel still goes into panic.

Good day, *newbie alert* I try to run * with capi_chan (and later on SIP). System: Debian 3.0 / apt-getted most stuff except chan_capi and b1.t4 HW: AVM B1 ISA / Celeron 400 / 128MB RAM Starting * the following ends up in the messages Jul 22 19:47:03 WARNING[16384]: File chan_mgcp.c, Line 2925 (load_module): Unable to get our IP address, MGCP disabled Jul 22 19:47:03 WARNING[16384]: File

Hi all ! We have 3 NTBAs which are all going to our existing PBX. Our areacode is 06003 and our DDI enabled number 9141. I want to exchange that PBX with Asterisk, but still struggle to get it working. My CAPI.CONF is currently like this: [general] nationalprefix=0 internationalprefix=00 rxgain=0.800000 txgain=0.800000 [interfaces] context=in-capi msn=60039141 incomingmsn=* controller=1

Hi * Fans, I have some fritz cards now, followed instructions from stuart hirsts email of Jun 28: -> Thanks for your info but I think I have it working at last. Below are the steps I took which might help others. 1) Download the PCI AVM drivers from ftp://ftp.avm.de/cardware 2) Download the Chan_capi from http://www.junghanns.net/asterisk/ 3) tar -xvzf fcpci-suse8.0-03.09.10.tar.gz which

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Not strictly Asterisk related, but I'm trying to get an AVM Fritz! card to work with Asterisk on a Fedora Core 3 box. I've grabbed the official AVM Fritz CAPI driver from the AVM website and compiled against the current kernel. However, as soon as I modprobe it I get: CAPI Subsystem Rev 1.1.2.8 fcpci: module license 'Proprietary'

Hi, i will use an AVM C2 controller with asterisk. How can i use both card ports ?? On the voip-info.org Wiki is only notice to: You will need a section for each controller in /etc/asterisk/capi.conf so the C2 will have 2 sections. But how is look like this ? Only on the first port is asterisk assume connections, but nothing on the second card port. In the dmesg is only the capidrv-1 shown,

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Hi again! > I have excellent success with the tiny "fcpci" and chan_capi, which is > also working great with capi4hylafax. See > net-dialup/fcpci-0.1-r1 in gentoo (should not be difficult to use this > on other distros, but I have never done so). Do not confuse this with > the "fritzcapi"! I managed to install fcpci and it seems to run fine (capiinfo

Someone have info about install an AVM fritz into FC3 ? I'm getting problems with kernelcapi, after succesfully installed the fcpci support. Thanks -- Adri? Vidal adriavidal@gmail.com Mail is better with 1Gmail

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi there, i'm in debian sid 3.1 with kernel 2.6.7, * last cvs & chan_capi 0.3.4b; nt1+ with 2 bri in ptmp (http://www.voip-info.org/tiki-index.php?page=DDI) i tried to install avm c4 following step by step http://www.voip-info.org/tiki-index.php?page=Asterisk%20How%20to%20connect%20with%20CAPI step 1. i compiled capi 2.0 support in kernel

Hi to all asterisk-users ;) As some of you may know, Kernel 2.6.32 includes a module for the infamous Fritz passive ISDN cards in conjunction with mISDN. I just would like to know if anybody has tried to use a Fritz card as a BRI adapter for Asterisk with the new module. If so, i would be grateful for some hints or howtos. I am willing to try this myself, but i am quite reluctant as i have

Hi Armin! I have problems on debian sarge with standard 2.6.8-2-386 kernel. I've installed the packages: kernel-headers-2.6.8-2 kernel-headers-2.6.8-2-386 kernel-image-2.6.8-2-386 kernel-kbuild-2.6-3 kernel-source-2.6.8 Then I unpacked the kernel sources into /usr/src/kernel-source-2.6.8 and made a symlink from /usr/src/linux --> kernel-source-2.6.8 Then I entered

Hello, I want to use a 4 port ISDN card from EICON/DIALOGIC in our asterisk server. The system is a Ubuntu 7.10 with kernel 2.6.23.1. The compilation of the kernel finishes without any problems. I have downloaded and installed the deb-source package that EICON/DIALOGIC offers. Th installation script crashes with the following error messages: # LOG ---- START SECTION read kernel version

hello, got anybody succesfully setup asterisk with three avm fritz pci cards - using the howto described in http://www.quiss.org/caiviar/Two-Fritzcards-HOWTO i already have asterisk working with 2 cards, by when i add third card and compile driver ( see capiinit debug below ) asterisk freeze on capi initialization.... does anybody know how to solve this ? regards Marian ------------------

HI all, Has anyone succesfully installed an AVM Fritz! card on Fedora 7 using the drivers at ATrpms recently? http://atrpms.net/dist/f7/fcpci/ I tried with a clean F7 build on my EPIA 5000 yesterday, after modifying /etc/capi.conf (removing the coment # in front of fcpci line) I received the following error when executing 'capiinit' - FATAL: Error inserting fcpci

Hi Folks, I have to setup a new server with a fritz-pci-ISDN-card inside. For it the fcpci-Packages from atrpm-repo is needed. Trying to install this package on a machine with the newest CentOS5-Plus Kernel I get an error message Missing Dependency: /boot/vmlinuz-2.6.18-8.1.14.el5 is needed by package fcpci-kmdl-2.6.18-8.1.14.el5 Okay -I have a vmlinuz-2.6.18-8.1.14.el5.centos.plus. Any

I tried that but it still doesn't work... I think I don't have the correct approach. Have I to install any ISDN drivers (=modules ?) BEFORE dealing with CAPI ? If yes, why shouldn't I use the hisax drivers (which are kernel ones) instead of fcpci drivers (which doesn't seems to work, by the way...) And finally, how is it possible to link the two modules together? As you can see,

Hi list, i'm keen to move to Asterisk 1.6, so really need to update my system which is running Mandrake 9.2 although it has been solid for years, fo Fedora 8. I have a Fritz! card for ISDN BRI, I have installed the drivers/kernel drivers from ATrpms (http://dl.atrpms.net/all/fcpci-03.11.07-14.fc8.i386.rpm and http://dl.atrpms.net/all/fcpci-kmdl-2.6.23.14-115.fc8PAE-03.11.07-14.fc8.i686.rpm)