similar to: codec used on E1

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

Hey all! I had an experience trying to set up an E1 in Brazil which could help somebody. In Brazil is very common telcos to have just R2 digital as their primary signaling. As I were trying to set up an E100P, which does not support R2 yet, I had to test an other signaling which works perfectly with Asterisk. They call this signaling as RDSI, using ccs as framing and PA (primary access) as

Hi, I am currently trying to find a replacement for a dinosaur PBX and want to replace it with a VoIP solution. We have just moved our lines over to an Optus Multiline from a Telstra ISDN Onramp 30 service with 100 lines. My question for you good people is what sort of hardware do I need to interface Asterix into the Optus Multiline? The Optus service is terminated in my office to a SHDSL

Hello I have an office with a T1 that provides 4 (out of 8) analog PSTN lines thru an adtran board. I want to add 4 more analog lines. Currently I have a Digium TDM40B. I'm wondering what the best upgrade path is, where I define 'best' as the solution that is most likely to work without problems (like interupt conflicts) and work with my current echo tuning . I see my purchase

hi guys, I have a little problem maybe you can help ... I have an asterisk setup, with an E100P, and an ISDN-PRI 30 channel line from the telco going into it .. the E1 line is OK, because plugged into a Lucent Portmaster 4 it works OK .. plugged into the asterisk box I just get an engaged tone, and asterisk posts this message on screen : WARNING[1167272000]: File chan_zap.c, Line 5275

Hello list, i've got some problems getting a E1 line with a E100P up and running (germany). # cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS/CRC4 YELLOW RED "YELLOW RED" sounds not so good. When launching asterisk, enabling pri debug on that span, i see outgoing attempts: ;---------- snip -------- > [00 01 7f ] > Unnumbered

Hey all, I have an Asterisk-box with an E100P and a PRI (Euro-ISDN) coming into it from a Meridian-switch. The incoming numbers on this PRI all start with the same digit and the last part of the dialled number is signalled to Asterisk digit by digit, until Asterisk signals that the number is complete and the call rings. All works well, unless I have 2 or more numbers which start with the same

Hello Folks, I'm trying to decide here between a few cards for connecting an Asterisk box to a single E1 channel (either PRI or R2 signaling): - Digium E100P: has been replaced by the TE110P below, but can still be had at places like digitnetworks.com for $475, and I guess there's always a place for good-olde-obsolete cards in the world as long as they work :-) - Digium TE110P:

I went on a service call yesterday to find an asterisk system with a T100P card on a Qwest PRI and a TDM40B card connected to fax machines. The TDM40B LEDs were not lit, and the system did not respond to keyboard input. However, calls were being processed for the PRI and 7960 phones. I replaced the TDM40B card with a new one, and the system now seems to be ok. But I'm wondering, why

Hi list, I'm trying to set up a TDM40B, but modprobe returns the fowling errors: asterisk:~# modprobe wcfxs ZT_CHANCONFIG failed on channel 1: Invalid argument (22) /lib/modules/2.4.18/misc/wcfxs.o: post-install wcfxs failed /lib/modules/2.4.18/misc/wcfxs.o: insmod wcfxs failed Could someone give me a help? Thanks in advance Eduardo

Hi, I'm no phone guy but I've been having quite a bit of fun messing with Asterisk. I just unwrapped my new Wildcard TDM400P (TDM40B) which is the new 4 port FXS PCI card. It has 4 RJ45 connectors and I'd like to hookup 4 regular phones which are RJ11. If I crip RJ45 connectors to the phone cords do I simple use the center two pins (pins 4 and 5)? Thanks, Randy Smith Tiger

We are not having any luck with the E100p card here in Australia, it will work with a crossover cable to another device but will not talk to our Telco Telstra who probably have a weird implementation of an E1. Any suggestions on a replacement? Regards Mark McKibbin DCS Internet 64 Queen St Warragul Victoria 3820 Australia www.dcsi.net.au mark@team.dcsi.net.au Ph. 1300 665575 Fx. 1300 556595

hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'.

Hello ml, i need some help on my zaptel configuration. My E100P only shows some YELLOW / RED alarm when I load the wct1xxp module and do a cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS YELLOW RED ... .. . My /etc/zaptel.conf is: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=nl defaultzone=nl I tried zaptel-1.0RC2 and the latest CVS

Hi all, Does anyone run Asterisk on FC4? with Digium's TDM40B cards. any success stories? my Intel 865 M'd+ Intel 3.0GHz freezee during installation (FC4). Please any comments? Kumara

Hullo everyone, Iam new to Asterix but am trying to get R2 signalling working with a Digium E100P E1/PRA Card. My Telecom doesn't have an implementation of ISDN PRI yet, so it's R2 that is supported. Could anyone have a patch to fix this for me. Am told it has something to do with Assembly Language programming. Please help me fix this. Regards, Nicholas

OK, I have a Asterisk @ Home 1.0.7 server with two Digium TDM400 cards, one 4 port FXO and one 4 port FXS. When I plug an analog cordless phone into the TDM40B card and setup a ZAP extension, the phone rings in and you can answer just fine. The weird part is when you try to get dialtone from the cordless handset it rings all of the other extensions... One other thing to mention is that the

Hi, I am building for a customer an * solution that will use 2 Digium cards. 1 x TE110P (T1 ISDN PRI) 1 x TDM40B (4 analog ports, 2 for faxes, 2 for extensions) The system will be connected to the PSTN through the T1 ISDN PRI interface. All customer extensions will be SIP phones except 2 fax machines that will use the analog FXS ports on the TDM40B card. I have been investigating on this

Hi, i just received an E100P, this is the first one I have ever seen, and notice that the board reads T100P. Is this right ? The antistatic bag had a small label that has E100P written on it, and the card is a bit different than the T100P I already have, Does Digium use the same boards for both cards ? I don't have an E1 link here, can I test the card just by loading the driver and run

Hi, I currently have a E100P card installed on my machine and the E1 subscription will be activated pretty soon. However, I have no idea how to configure asterisk to make inbound and outbound call using the E1. Especially for extensions.conf. Below is the configuration I used for zaptel.conf and zapata.conf. Is it possible if someone can verify if the configuration for zaptel and zapata is