similar to: Data through T1, nethdlc

All, I am trying to configure hdlc support on T100P Digium card - everything seems ok... but it just does not work at all. I was able to compile all drivers, the light on the card becomes green when I plug T1 link.... but I even can't ping default router IP... there is no data coming back to me, so I am confused completely now. Also I tried both protocols - raw hdlc and cisco hdlc. The

Hello All, I am battling a problem I don't know how to fix... Here is the scenario: Fractionated T1 with 1-6 channels voice, 21-24 channels data. Comes into a box with Digium T100P, splits off data channes with HDLC, to devicec pvc0, This works fine, but I have a routing problem getting to my machines! Here is the current set up... sethdlc hdlc0 fr lmi ansi sethdlc hdlc0 create 44

All, I'm having a heck of a time getting hdlc to work on kernel 2.6.11.9 .. I compiled hdlc, hdlc_gen, hdlc_cisco, hdlc_raw, into the kernel (note into, and not 'modules'). System comes up, I configured zaptel.conf span=1,0,0,esf,b8zs nethdlc=1-24 modprobe wct4xxp ztcfg sethdlc hdlc0 cisco ifconfig hdlc0 up All of this works fine, believe it or not. I have a T1 cross plugged

Greetings- I'm wondering if the Digium PRI cards can be used for data (Cisco HDLC, PPP, etc) or if they're for voice circuits only. I haven't been able to find any information on this. All documentation direct from Digium seems to indicate their hardware is for voice applications only. Sangoma's cards work in either voice or data mode but of course this is configured in their

Hi, I believe the issues raised by this message are the same as mine, more on a commercial sense than for self use, but mostly the same. I've seen posts where real-life installations are mentioned, but not a reference to how Asterisk is working on production (and productive) environments. Any experiences would be very welcome I believe, not only on pure technical, but wider, sense. Thanks

Hello everyone, We have recently turned up a new T1 from McLeod (Midwestern CLEC). It is configured like so: /etc/zaptel.conf: loadzone=us defaultzone=us span=1,0,0,esf,b8zs ;(also tried 1,1,0,esf,b8zs) bchan=13-23 nethdlc=1-12 dchan=24 /etc/zapata.conf: switchtype=national context=pri-in signalling=pri_cpe group=1 channel => 13-23 I can get hdlc0 (and pvc0) up just fine after the

I have my Linux 2.6 kernel with the necessary HDLC config and also recompiled zaptel accordingly. On modprobe, I get: Found a Wildcard: Digium Wildcard T100P T1/PRI Debug: sleeping function called from invalid context at mm/slab.c:2000 in_atomic():0[expected: 0], irqs_disabled():1 [<0211e605>] __might_sleep+0x82/0x8c [<02144643>] kmem_cache_alloc+0x1d/0x57 [<42ad7a2c>]

Hi List, I am sorry that I may bring the old question to the community. My question is 1. How can we determine if asterisk is working normally or not ? what kind watchdog process do we have at this moment ? 2. In case the running asterisk is mulfucntion, is there any available way to auto restart asterisk ?? Please advise if you could. Thanks.

Hello all, We have a TE405P set up with span 1 running to a channel bank, a PRI running into span 2, and a PPP internet T1 running into span 3. We have the first 2 spans up and running without a problem. We have hdlc compiled into the kernel and after making the appropriate changes to zaptel.conf and loading the zaptel, wct4xxp, and hldc modules we can bring up the third span with the internet

Hello, I contacted Krzysztof Halasa, the maintainer of the current sethdlc code. This is the response he gave me. Of course, I have this working now. Still some minor configuration to do, but It does work, and the connections to the internet are _much_ faster than when I went through the adtran... I would highly recommend to anyone with a fractionated T1, with data and voice channels to

my target is to produce a linux router with T100p to Fract T1 24chan to ethernet and TDM 4channel FXO. I have not been able to get nethdlc to work, just get zaptel networking not configured if I set bchan and dchan the card comes to life, but I don't believe this is correct for what I want to accomplish. according to markster@ this is the way they do it. using (multiple distro versions

Hello! I want to use TE121 for E1 data link to cisco. Really only for tests now. So I wrote: span = 1,1,0,ccs,hdb3,crc4 #span=1,1,0,esf,b8zs nethdlc=1-31:hdlc0 may be first line is wrong, problem is somewhere else anyway. Just because I get: # dahdi_cfg DAHDI_CHANCONFIG failed on channel 1: Function not implemented (38) This is centos 6.4 box with dahdi 2.7.0.1. Could you tell me is it

I got it figured out now. In case anyone else comes across it - this is what I had to do: Sethdlc hdlc0 mode ansi Ifconfig hdlc0 up ***NO IP INFO SET*** Sethdlc hdlc0 create <dlci number> Ifconfig pvc0 <local ip> pointopoint <remote ip> up Then set your default gateway to the <remote ip> listed in pvc0. That's about it!! Hope it helps! -----Original

Hi, I am facing problem in configuring D-channel. I did the following configuration for TE-120P card /etc/zaptel.conf span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 /etc/asterisk/zaptel.conf group=1 signalling=pri_cpe switchtype=euroisdn context=incoming channel=1-15,17-31 DIGIUM card is connected through cable to another end.On placing call from other end to

I'm setting up a T1 for both voice and data and was wanting to know the steps involved. I've recompiled zaptel for ZAPATA_NET support and setup my /etc/zaptel.conf: Fxsks=1-10 Nethdlc=11-24 Modprobe wct1xxp works fine and my voice lines work. Now when I use the provided sethdlc, I use the following commands: Sethdlc hdlc0 mode ansi Ifconfig hdlc0 <ipaddress> <network>

Is it possible to run NETHDLC and PRI signaling on the same 4 port T405P card? This is what I get when I try to start asterisk: == Parsing '/etc/asterisk/zapata.conf': Found Mar 24 10:48:53 ERROR[2368]: chan_zap.c:9435 setup_zap: Unknown signalling method 'pri_cpe' Mar 24 10:48:53 WARNING[2368]: chan_zap.c:9614 setup_zap: Ignoring switchtype Mar 24 10:48:53

I need to know how to setup the data side of the T1 on my Linux Box. I have found information about configuring a PRI and HDLC but nothing about the Frame-Relay type setup for data. The following is information from our T1 provider. Network T1: Framing = ESF Line code = B8ZS Build out = 0-133ft(DSX)/0dB(CSU) Clock = network Pulse-density-enforce = off alarm-option = on alarm-delay = 15

After speaking with several people, and even participating in a forum of several other people with echo issues, I thought I'd share what we've done (well actually what our chief R&D engineer, Brett Bourn has done...) First let me say that normal cheapy PC hardware couldn't be made to function with out echo. We tried on both the single port Digium T1 card and the 4 port Digium T1

Hi, all I have installed TDM400 with 1 FXS and 1 FXP ports. Now I am goig through documentation on how to configure it. It mentions 3 protocols: Loopstart, Groundstart and Koolstart. Which one do I use? Can someone send me sample zaptel.conf file for Australia? This will save me some time and will be used as a working example. Thanks, Rudolf

Hey guys, appreciate the input. Here are some thoughts. ADSI phones are out of the question. This is a business environment, I can't worry about my employees not knowing how to forward calls, answer calls when away from the multiline phone, and no ADSI phone will handle multiple lines that I have found. I would love to put 6 X100P cards in a case and run asterisk on it. but... I