similar to: IAXy

In features.conf, I have uncommented the transfer features under feature map, but I still cannot transfer using a POTS phone on an IAXy adapter. I think I am missing something here.... Any help is appreciated. Here is features.conf: ; ; Sample Parking configuration ; [general] parkext => 700 ; What extension to dial to park parkpos => 701-720 ;

I've heard comments about the instability of the IAXy (loosing IP, locking up, etc) . I want to deploy some, in a remote site. The comments on the instability suggest that the simplest approach is to power-cycle them when you have problems. The IAXy would only be in use from 3PM to 8 PM. My potential simple solution is to have a timed power brick (like what you would use for a block heater)

Hi, I've got an IAXy, and provided it with connection data - unfortunately didn't provide a fixed ip address, but left with dhcp. Everthing went fine, and I could work a while with it. After a restart of IAXy, it didn't negotiate a new IP address, nor used the old one. I even restarted the DHCP server and cleared its cache. No success. I went to another office with a different

I place a call from an IAXY to an IAXY device. INitially the calls show in the output of "show channels". Then after a few seconds the "show channels" command shows 0 active channels even though I am still talking on the channels. Any ideas on this? THanks, Jerry

Ok, I searched the lists and found no definitive answer. I'm assuming the IAXy has some primitive form of echo cancel, is there anyway to adjust this? Or any ideas on what to do instead. Here's the setup, this will not be a typical setup for our company however, well whatever. Anyway it looks like this: IAXy --> Netgear router --> Charter --> Level3 --> Asterisk --> VOIP or

There is no DNS functionality built into the IAXY, I am assuming you want to be able to home onto a SOHO site with a dynamic IPaddress. I have not been able to figure out a clean way to do theis (make it easy for the roaming sales-folk etc,) who will not have a high tolerance for running something like an IAXYPROV. You would need to somehow have an external fixed address which would

Hi all, getting a server going wiht a few TDM400's and some phones, and some IAXys too I haven't heard any issues about AU phones being able to RING in Australia, like the problem in the UK with ring capacitors on the BT system. Are there any problems like that? Also, with the iaxy's -- they should work (and ring) in Australia right? The only hint I'm seeing around is the use

Hi all, I have a small query regarding ringing tones on an iaxy2. I have a customer who uses an iaxy to breakout to pstn via our *. However the customer complains that he gets no ringing tone whislt making calls, i just visited the site and can confirm this. I also have another customer who is presently in canada with an iaxy calling thru our * , he doesnt have this issue. I presume that the

Hi All; I need to buy one IAXy device, but I discovered that it supports only g711 and ADPCM codec, so I was wonder that it does not support g729 or GSM?! Anyway, what is that ADPCM and how much it consumes bandwitdh? Also, asterisk support such codec? What its name in the configuration? Any advise? Regards Bilal

I am not sure if this is the place for Digium user-to-user discussion, but... We have deployed many (20+) IAXy's in the field. At a couple of locations, the IAXy's have just stopped working after 1 or 2 days use. No lights go on, no DHCP lease is renewed as far as we can tell, and of course no dialtone and no registration with the server. Has anyone else experienced high failure rate

I have a couple Iaxy's and when calling out on them I dont hear ringing. Everything else is working fine. Any ideas? THanks, Jerry

According to http://kb.digium.com/entry/12/ The Iaxy will respond to pings on port 9999. You can ping your broadcast IP on your network and listen with tcpdump on your network on port 9999 which will show the Iaxy responding and what IP address it is coming from. Ex. ping 192.168.1.255 tcpdump -i eth0 udp port 9999" Before I get my karma whacked again, does this work for

Hello. I picked up a couple of IAXy's for testing. Unfortunately, I read the negative comments only after I bought 'em :( Regardless, I provisioned one unit using my local Linux computer. Now, I'm trying to set it up to provision using the remote * server whenever it tries to register, but it seems I need to know the "service identifier" for the specific device. I can't

Hi.. I have to setup an extension in a remote location that will use a cordless analog telephone.. I am looking at the IAXY to do this for me..Basically the data path will be as follows... [Asterisk] == (NAT) == {Internet} == (NAT) == ATA -- Handset Since there are two NAT boxes in the path I know SIP won't work.. I also don't want to move the Asterisk box to the internet side of the

For anyone playing around with IAXy(S100i) devices, I am making the following available: Windows IAXy Provision v1.00 This is a from-the-ground-up development of a means of provisioning IAXy devices using a Windows environment. For some users, being bound to Linux for IAXy provisioning is not viable or convenient in some cases. This application provides a GUI data entry for the various IAXy

Hi, I have three Iaxy devices (s101i) parts. Two of them seem to work fine. The third plays a loud repeating click sound when an analog phone is plugged in. I can provision all of them, and make calls to all of them. The clicking one will blink when a call is incoming, but no audio from the call can be heard on the handset, and the caller only hears silence. The same handset works on the

I can't seem to get this device to grab an ip from dhcp. We have a working dhcp server (unfortunately it is on Windows), but I don't show any leases requested by the iaxy. Anyone have any ideas? The ethernet and phone lines are plugged in before the device is powered. Thanks, Erik

Hi all, I have a Soekris net4801-50 board with OpenBSD 3.9 where I've configured a dhcp server and tested it with a regular PC connected directly via a crossover cable with success. The problem comes when I try to connect my IAXy device instead of the PC. I can see with 'tcpdump -nettti sis1' that the IAXy isn't sending any packets to the dhcp server. I thought my IAXy was bad

In the mailing list archives, I found a message that indicates that the IAXy has the ulaw, alaw, and g726 codecs, but I cannot find anything official on Digium's site about it. The Installation Manual has an example iax.conf file that indicates the ulaw codec, so I know that one is good. But we are thinking about using the IAXy over a VPN, to replace our MultiVoip. alaw and ulaw are

I have a brand new IAXy I'm playing with. I do not get a dialtone on the phone, or any response at ll on the phone. No sound, no dialing, no ringing. The phone and wire are tested and known to be good. I think I have it setup correctly. When I give the iaxprov command I get this: #iaxyprov 192.168.1.90 iaxy.conf 02: c0 a8 01 5a 05: 11 d9 03: ff ff ff 00 04: