similar to: Max TE410P card on an Asterisk

Is there anything to choose, in performance, between a TE405P and a TE410P? I understand the difference between the PCI bus voltages, and certainly don't intend to try Andrew's hacksaw operation :-). But if I choose the card first, and a compatible mobo second, does it make any difference which? Cheers Tony -- Tony Mountifield Work: tony@softins.co.uk - http://www.softins.co.uk Play:

Hi, We're evaluating asterisk, somebody has measured maximum asterisk load (simultaneus calls, calls per seconds...)? Are there any stimation? Thx. Best regards. .G

Hi all, I'm looking for a new system which will use the TE410P. Originally I was going to use a dual Athlon MP system, but my supplier tells me these are being phased out now, and so will be difficult to find replacement parts later. So, I am looking for suggestions of suitable motherboards with 3.3V PCI slots for the following CPU types (in order of my personal preference) AMD Opteron 1xx

Hi all, Does somebody know how I have to setup my TE405P ? Is it correct my configuration below ? Otherwise, can somebody help me ? Thanks, Angel. zaptel.conf span=1,1,0,ccs,hdb3 span=2,0,1,ccs,hdb3 span=3,0,1,ccs,hdb3 span=4,0,1,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31 bchan=1-15 dchan=16 bchan=17-31 bchan=1-15 dchan=16 bchan=17-31

I am planning to buy Dell 2650 server with dual Xeon processors. And I would like to buy two TE410P cards for PCI with 3,3v. This is on Dell site about PCI slots for Dell 2650 server: 3 PCI-X (1x64-bit/133MHz, and 2x64-bit/100MHz) Does that mean I will be able to buy two TE410P cards ? Or I need to buy two TE405P cards ? Thanks for help. bartek

Hello, We have one production server that is identically configured to another production server except for the fact that they each use a different type of digium quad T1 card(one has T400P and one has TE405P). The server with the 405 has been developing delay problems with Sipura SPA-2000 phone adapters after a call has gone on for 15-30 minutes (up to 1 second audio delay). I asked Sipura and

Can anybody tell me the difference between a TE410P and a TE405P? Is it JUST the 5v vs 3.3v pcis slot spec, or is there some thing else? </edg>

Since i'm sure there are others out there in the same position as me, being disappointed that the original T400P and E400P cards are no longer available from Digium, I thought I would pass on a place I found to get them. I needed the older card, since I didn't want to have to get a motherboard with 3.3v pci slots on it.

Why PCI 3.3V for E1/T1 card!? I can not use it because I can not find any motherboard with PCI 3.3 . Any sugestions!? Cristian VASILIU AccessNET International S.A. Software Programmer mail to :<cvasiliu@accessnet.ro> www:<http://cvasiliu.home.ro>

Hi- I have posted a photo of the TE410P Digium card on my site, so that those wishing to purchase a compatible motherboard can see physically what the PCI slot requirement is: http://www.evtmedia.com/TE410P.htm I believe the required slot is a 64-bit, 3.3 Volt PCI, most commonly found on Xeon-based motherboards. A 64-bit slot is longer than the TE410P board requires, but the PCI connector

hi, after stumbling over the compile time flag in zaptel and after reading the new features of the 2nd generation firmware of the TE405P/TE410P, i was wondering if the cards are capable of upgrading the firmware in field? regards frank

Has anyone else experienced a problem with the LED for span 1 on a TE410P or TE405P? I had a TE410P on which the span 1 LED would not light red, but once the span was connected, it did correctly light green. I RMAed the board to our UK distrbutor and received a replacement. However, the replacement board displayed the same problem! Wondering if it was related to the computer I was putting it

Hi- I'm looking for an appropriate system board to power a system with two (2) Digium TE410P cards. Since these cards require the 3.3 volt PCI, I'm considering vendors like Tyan for the motherboard. Can anyone please tell me their experiences with the Tyan i7501 series (Xeon-basd), or recommend an alternate motherboard? Thanks Scott Scott M. Stingel Emerging Voice Technology Inc.

Dear List i have upgrade my * box with the latest CVS version of Asterisk Stable 1.0 and zaptel/libpri my system is MDK9.2 with 1 TE410P and seems work well for now but i have a little amount of traffic (25 IN/OUT calls) i only notice this Warning.. What kind of error is? ------------------------------- Apr 20 21:28:49 WARNING[147466]: chan_zap.c:5979 zt_pri_error: PRI: !! Got reject for

I am the proud new owner of a TE410P, and installed it on a RedHat 9 box. After compiling just fine, running like a champ in tests, and having my extensions.conf configured to taste, I went ahead and did a live beta test this past weekend. The phone system stopped responding 3 times. The first time, I got into the asterisk console, vi -rvvvvv. I didn't see anything too out of the ordinary,

hi all, i am getting crazy with my TE410P - it won't work now we already think that the only thing which can be wrong is the cable. At our telecom endpoint we have 1-2 tx, 4-5 rx So - which cable do i need to get it working Already tried a cross over cable 1-2 -> 4-5 / 4-5 -> 1-2 (with this cable nothing works -> red alarm on both ends) Also a normal cable 1-2 -> 1-2 / 4-5 ->

Hi, I have this strange problem I need some help with.. It appears that I have harddisk noise captured by a Digium TE410P card (Same problem on 2 identical machines..) The machines are two Compaq Proliant DL320 G3's... Does anyone else have this problem.. Kind Regards Claus Futtrup --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com).

Hi- I have an upcoming order for a bunch of asterisk boxes, and I'm considering using an "assembled" package for the server, instead of building them from components as I usually do. Does anyone have experience with the Dell PowerEdge 750 server, or any other 1U rackmount server for use with asterisk? Thanks in advance Scott Stingel Scott M. Stingel President, Emerging Voice

Is there anyone successfully using the TE410P with a German "PMX-Anschluss"? Please just drop me a note mentioning the carrier you use. We are having problems making the card work, although configuration is correct (Posted this before). Our carrier blames the card for this. We would just need some evidence that it really works. Thanks, Henrik -------------- next part

Hi list, We have been trying to configure a Quad Span T1 card in a system running RH9. We have followed the instructions in the Wiki and searched the mailing lists, but so far havent got any success. Cable is connected to the first span, and module is loaded. Without loading the module the LED glows in red colour, but the moment we load module, it goes off. (No red or green) . We ran zttool