similar to: About TE405P Digium Card

Good day everyone, A Solution now exists for those of you still looking for the first model of Quad T1/E1 Interface Cards - the T400P and E400P. The T400P and E400P were manufactured by Digium until a few months ago, and were designed and released under the GNU Public License as the Tormenta II by Zapata Telephony. Varion, Inc. is now in full production manufacturing these boards. With the

Anyone care to elaborate on the differences between the T400P and the TE405P? -Darren -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050908/e817f8bb/attachment.htm

Hi all, Does somebody know how I have to setup my TE405P ? Is it correct my configuration below ? Otherwise, can somebody help me ? Thanks, Angel. zaptel.conf span=1,1,0,ccs,hdb3 span=2,0,1,ccs,hdb3 span=3,0,1,ccs,hdb3 span=4,0,1,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31 bchan=1-15 dchan=16 bchan=17-31 bchan=1-15 dchan=16 bchan=17-31

Forget the sound card. It isn't related. The subject above should have read 'TE405P No Voice Problem' or something similar. It appears to be a zaptel timing issue, but I have found a workaround. For those of you just tuning in, here is the story: I have a CentOS/Intel 865 box currently running Asterisk 1.2.7.1 and zap 1.2.5, both compiled from the source available off the main

Since i'm sure there are others out there in the same position as me, being disappointed that the original T400P and E400P cards are no longer available from Digium, I thought I would pass on a place I found to get them. I needed the older card, since I didn't want to have to get a motherboard with 3.3v pci slots on it.

Hi, Urgently response would be wonderful, system is a Fedora Core 2. I have a Ericsson BP250 connected to 1 port on the TE405P and another connected to a local telco ISDN30. I have been running CVS-HEAD from about a 2 months ago and upgraded it again just in cause it was a version issue (didn't fix it) but this is what I am getting. When a person calls out from an extension on the BP250 to

Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much

We originally purchased a TE405P so we could connect our Asterisk server directly to the T1 PRI from our provider, however due to all the problems reported with T1 PRI's interacting directly with Asterisk, we scrapped that idea and decided to stick with our Cisco router making the conversion to SIP. Anyways, we found a new potential use for it. We have an old location with an existing PBX,

This works fine. Message: 26 Date: Tue, 7 Jun 2005 17:22:23 +0800 From: "Ma Zhiyong" <mazhiyong@sohu.com> Subject: [Asterisk-Users] te405p and dell poweredge To: <asterisk-users@lists.digium.com> Message-ID: <004501c56b42$6a12fcd0$7301a8c0@hylaclient> Content-Type: text/plain; charset="gb2312" Hi, I want to install * and te405p on Dell Poweredge 1850. Can I

http://www.mixdown.ca/~asterisk/ The card seems to be working fine. Don't expect warranty on it though. :-) Why? Because I wanted a quad-span T1 card which worked in the high-end systems I was intending it for, but that I could also keep a few in stock and if the system mainboard failed, pull the card an put it in a standard PC system. I didn't want to have to stock 3.3V and 5V

My Asterisk server believes that a Digium TE405P and sound are incompatible. Basically, no matter what else I do to the machine it terms of hardware, if the TE405P is installed, none of the playback/background/etc commands work. MOH works fine. So far, I have tried: 1) Seven different PCI soundcards with different chipsets. (Go go Computer Junk Store!) 2) Disabling each and every device

Hello, I would like to know if FreeBSD has drivers for TE405P cards submitted to the ports. I have acquired a card and would really like to use it with FreeBSD. The wiki said the drivers havent been tested yet. Have there been any updates since then? regards Kavit _______________________________________________ Asterisk-Dev mailing list Asterisk-Dev@lists.digium.com

Hi I got the 2nd Gen firmware upgraded on the TE405P. I recompiled after putting in the upgraded board but did not change any conf, but the spans become active but will not come up. I guess I am missing something or are the any changes to the zaptel/libpri software that is required. I cannot find any info about this or does this new firmware only work with latest CVS. I am using 1.0.9 with

Hi, I'm looking into support for SS7 and I found an article (http://www.openss7.com/news13022002.html) which says that OpenSS7 supports Linux Support Inc's T400P-SS7 Quad T1 and E400P-SS7 Quad E1 PCI interface cards. It also says that Linux Support Inc is the primary sponsor of Asterisk. However I cannot find these cards on the Asterisk hardware page

I'm installing TE405P card. This is my zaptel.conf. -------------------------------------- span=1,0,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 loadzone = us defaultzone= us -------------------------------------- When i modprobe wct4xxp, -------------------------------------- PCI: Found IRQ 11 for device 02:0b.0 PCI: Sharing IRQ 11 with

Hello, We use all SCSI PCI card hardware RAIDs on all 4 of our production Asterisk servers. They all have Digium quad T1 cards and they all have from 2 to 4 T1s hooked up to them. We have had no noticable problems with dropped calls/poor quality. What are you looking to do with this system? what kind of traffic will be going through these 4 T1s? MATT--- -----Original Message----- From: Deon

Hi, I want to install * and te405p on Dell Poweredge 1850. Can I do that successfully? Any one has successful experience on that scenario? Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050607/fb7408a1/attachment.htm

Is there anything to choose, in performance, between a TE405P and a TE410P? I understand the difference between the PCI bus voltages, and certainly don't intend to try Andrew's hacksaw operation :-). But if I choose the card first, and a compatible mobo second, does it make any difference which? Cheers Tony -- Tony Mountifield Work: tony@softins.co.uk - http://www.softins.co.uk Play:

Can anybody tell me the difference between a TE410P and a TE405P? Is it JUST the 5v vs 3.3v pcis slot spec, or is there some thing else? </edg>

hi, after stumbling over the compile time flag in zaptel and after reading the new features of the 2nd generation firmware of the TE405P/TE410P, i was wondering if the cards are capable of upgrading the firmware in field? regards frank