similar to: Siemens EWSD 13

Hi all, We're trying to hook up our Asterisk config (Card: TE410P) with a Siemens EWSD switch. The link is ok on both ends (green), with no errors. The problem is when we try to make a call from our side (via call files), we get the pri/E1 error Ext: 1 Cause: Temporary failure (41), class = Network Congestion (2) Our Telecom partner (they checked with Siemens) mentioned that we need to

Can anybody recommend a good web interface for asterisk that actually works. I am looking for a web interface that can show how many callers are on the phone, should be able to transfer the calls and disconnect. I have tried using the flash operator but has been unsuccessful in making it work. thanks -----Original Message----- From: asterisk-users-admin@lists.digium.com

Hello All. I'm using sangoma card A-101. tested successful with E10 (ACATEL) Exchange, connection with E1, CAS, (using unicall-0.0.3pre4). my system run success, incoming call and call out are good. when i switch to EWSD (SIEMENS) R-15 . my asterisk faill, cannot connect with EWSD. (E10 and EWSD exchange store in two provinces difference. in Vietnam) this is my logfile of E10

Hello all, I am trying to connect asterisk to a Siemens Hipath 3750 PBX system. I have a physical connection issue. I know that I should use a crossover RJ48 cable to link the two systems. The problem however is that the physical interface of the Siemens system is very unfamiliar. From my digging around, I think that this is an S2M interface. http://www.mail-archive.com/asterisk-users at

Hi all, I have a connect between a siemens hipath & Asterisk system over PRI The connection works perfectly I can call from the Hipath to an Asterisk Extension. I want to allow the hipath extensions to dial out over a SIP trunk on asterisk but I keep getting "The number you have dialed is not in service" In this CLI I'm dialing from hipath extension 9 (prefix for sip trunk)

Hello all. I have installed and functioning asterisk-1.2.9.1 where I effected one upgrade in asterisk-1.0.9, is interconnected with a PABX Siemens HiPath 4000 in ISDN PRI with protocol QSIG, the one that is happening he is that the calls originated for PABX Siemens and destined to SIP phones asterisk are being without audio, nor Ring, is dumb. They could help in this case me? Best Regards Josu?

Hello Everyone, What kind of hardware setup would I need to do if I want a T1 connection to PSTN and have 48 users in office with analog phones. Will something work if I have a T410P card in asterisk and have one T1 going to PSTN and other two to a channel bank. I would then connect the 48 phones (FXS) to the channel bank! Thanks. Deepak

Anyone have any experience using gr303? May have a need to interface * to a Siemens Class-5 CO for pstn trunking (inbound and outbound). Rich

Is there anyone successfully using the TE410P with a German "PMX-Anschluss"? Please just drop me a note mentioning the carrier you use. We are having problems making the card work, although configuration is correct (Posted this before). Our carrier blames the card for this. We would just need some evidence that it really works. Thanks, Henrik -------------- next part

Hi I've bought the Wildcard TE110 some days ago but I'm unable to get it to work with Siemens HiCom 300. I've tried this so far: 1. I've used standard cat5 cable cut off on one edge and twisted wires 1 to 4 and 2 to 3 which is according to cisco a short circuit for E1 lines. Wildcard takes a few seconds and sets the link to green (OK). 2. I've tried to connect our running

Hello all, I really checked voip-info.org but it still seems to be not very easy and I just hope that there is anybody with a simular config. We have one PRI (euroisdn with 30 channels) coming from the DTAG. The second PRI should be connected to a Siemens Hicom 150E Pro Office PBX (was cheaper than a channel bank :-) Carrier ----S2M------ * -----S2M------Siemens | |

Hello that might would be an easy question for someone, but im in doubt Is there any possibility to pass a call from one asterisk to another and then to ZAP channel. For instance I have "A" asterisk with numbering 45670 "B" asterisk with numbering 45680 second asterisk has TE110P card with single PRI port connected to Siemens EWSD. When I originate call from asterisk

Hello! Is it possible to connect Siemens HiPath 4000 to Asterisk? What equipment required on Siemens side? I mean IP not E1. Sorry for asking here. Siemens-related websites use "salesperson language". There is no technical information.

I've tried timing faxes two ways:

Hi, after loading the zaptel driver wct4xxp I have strange log lines in the syslog: Out of storage space. free tells, that more than 900 MB are still free. Disk space is also available. I'm using a dual opteron in 64 bit mode. Any ideas? Roger. Syslog: Dec 1 02:18:37 ipphone4 kernel: TE410P: Launching card: 0 Dec 1 02:18:37 ipphone4 kernel: TE410P: Setting up global serial

Hi, Is this card the same as the T410P, after all, it's made by Digium. There's one prior reference on the mailint list[1] but it didn't answer the question. There was also an SS7 status report[2] last June but it's doesn't seem to have lead anywhere either. There was post saying an SS7 release was immenent last September[3], but then silence. Any info anyone would like to

hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'.

Hi All I have problem with LIBMFCR2 for once Exchange I using Sangoma card, the firstly. my ssystem run successful with MFCR2, connected to E10 (Acatel Exchange), after that, i move connection connect to EWSD (Siemens), my system don't work. error protocol R2. my system: Asterisk CVS 1.1.X LibMFCR2 pre.005 and unicall-pre.005 this's my setting and my setting wanpipe1.conf

hi all, i've now installed a TE410P (Quad T1/E1 Primary Card - Digium) and connected it to a primary line. My telco (eTel) only told me that they are using hdb3 and crc4. So i still don't know which coding i have to use (cas or ccs) - and what timing options i have to use. Have someone already get a card like this up in Austria with a line from eTel or from the telekom Austria ? Another

Hi, I am having some problems mentioned below, the box is in production live environment with traffic around 30 - 100 calls. I am running T/E410P in a Dual P4 xeon with HT disabled. I am using zaptel 0.9.0 and asterisk stable 1 release. There is no gui, just mysql, perl (small script) and asterisk. System runs very smoothly if the calls are around 40-50 and comes one by one , however sometimes