Displaying 20 results from an estimated 8000 matches similar to: "Buzzing on TDM400P FXS?"
2014 Apr 28
2
Buzzing / Humming Noise
Hi
Lately I've been having problem with the handsets on the polycom phones.
The agents are complaining that the humming/buzzing can be heard on random
days.
When the agents touch their computer the buzzing may increase louder or
reduced. Also when they grab the handset cable, the buzzing noise is less
loud and is loud again when I let it go.
I have tried changing the handsets, problem not
2009 Jan 24
3
no dial tone tdm400p
This is, hopefully, just a case of brain fade.
With zapata.conf and zaptel.conf in place, asterisk loaded, no dial plan and all LEDS on the card lit, I get no dial tone, plugging an analog phone into ports 1 or 2, only a buzz and click.
zaptel.conf -
defaultzone=us
loadzone=us
fxoks=1,2
fxsks=3,4
zapata.conf
[channels]
signalling=fxo_ks
language=us
context=phones-1
group=0
2005 Feb 09
2
Problem using TDM400P FXS card
Hello, everyone
After having spent several time to look for any
solution for my problem, I decided to write here.
Here is the problem got a Digium X101 FXO card and
Digium TDM400P alias freshmaker (1 fxs module on it on
first port ) in my asterisk box. The X101 works
perfectly.
The problem comes from the TDM400, when i plug a
tested working phone on it , i get no dialtone; the
goal is to
2004 May 19
4
TDM400P problems with 1 FXS, 1 FXO
Hi-
I'm totally stumped configuring my TDM400P with one FXS and one FXO
module. Before I got the FXO module, I used to have an X101P, and
everything was working very well. Now * doesn't seem to recognize the
FXO channel. I've searched the wiki and the list archives. Stock Debian
3.0 stable installation. Any advice? Thanks.
-- David
Here's my configuration:
modprobe zaptel
2005 Aug 12
2
Possibly bad FXS module in TDM400P?
I've got the latest zaptel and cvs asterisk software loaded on my phone
server running FC3. And yes, It's fully updated and udev is setup
correctly. I've got a TDM400P with one FXS and one FXO module
installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this:
[root@asterisk ~]# ztcfg -vvv
ZT_CHANCONFIG failed on channel 1: No such device or address (6)
Zaptel
2005 Jan 06
1
TDM400P - Segmentation fault
Hi all,
I'm trying to install a TDM400P card, and I need some help.
Please, see below...
after dmesg command:
[root@voip root]# dmesg
via82cxxx: board #1 at 0xD800, IRQ 5
Zapata Telephony Interface Registered on major 196
PCI: Found IRQ 3 for device 00:09.0
PCI: Sharing IRQ 3 with 00:10.1
Freshmaker version: 71
Freshmaker passed register test
Module 0: Installed -- AUTO FXS/DPO
Module 1:
2007 Mar 30
1
bad case of buzzing
Hello,
We are at wit's end on this. One (and only one) of our five asterisk
installation is giving us real headaches. Buzzing and/or choppy sound
interfere with conversations. I recorded some conversations with
monitor() and no problem whatsoever appear in the recording, while the
local user was hearing the buzz and half my words.
This is a 1.2.16 installation with mISDN but mostly using
2003 Nov 03
2
MWI - I know this has been discussed in depth already
Let post this question.. Because I must be real slow... The following is
my config on this...
group=1
context=default
signalling=fxs_ks
channel => 1
context=local
signalling=fxo_ks
callwaiting=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
echocancel=yes
echocancelwhenbridged=yes
relaxdtmf=yes
rxgain=1.5
txgain=1.5
immediate=no
musiconhold=default
usecallerid=yes
2009 Feb 24
2
Configuring chan_dahdi.conf for Sangoma A200/Remora FXO/FXS Analog AFT card
Hi I have been having a rough time getting a Sangoma A200/Remora FXO/
FXS Analog AFT card set up properly.
The main issue is that the card has four ports and as far as I can
tell Asterisk is only seeing two. On the two that it recognizes the
"Green" FXS ports are not green, they just are not lit. The "RED" FXO
ports are indeed red, but from what I have read your not
2005 Jan 31
7
TDM400 stopped working
I excitedly installed my TDM dev kit earlier this weekend, installing
asterisk and all the kernel drivers to make it work. And it did, it was
fantastic.
I then reboot the machine, and even after doing a modprobe wctdm, I get
the following:
== Parsing '/etc/asterisk/zapata.conf': Found
Jan 31 13:34:27 WARNING[342]: chan_zap.c:793 zt_open: Unable to specify
channel 1: No such device or
2007 Jul 26
1
tdm400p fxs module busy
Dear All
The setup is te110p with an 8 channels PRI to make and receive all calls.
SIP phones throughout the company.
TDM400p with 4 FXS modules to send/receive faxes and make credit card
transactions.
I have an analogue phone on the tdm400p for testing.
I can receive calls to the exten. There is a dialing tone.
However, when I try to make a call I get a busy signal.
Asterisk stated busy then
2006 Jun 08
7
Fun with Echo
I've spent the last week or so troubleshooting echo problems at my
Wife's business, and I've been able to clear up about 99% of the
echo, but there is still a little residual echo that I can't seem to
"tweak out". The users describe it as "buzzing or crackling", but
what it sounds like to me is a slight echo, but just of one syllable
of the word.
2005 Jan 07
1
TDM400P - Segmentation fault - Help!
Hi all,
I'm trying to install a TDM400P card, and I need some help.
Please, see below...
after dmesg command:
[root@voip root]# dmesg
via82cxxx: board #1 at 0xD800, IRQ 5
Zapata Telephony Interface Registered on major 196
PCI: Found IRQ 3 for device 00:09.0
PCI: Sharing IRQ 3 with 00:10.1
Freshmaker version: 71
Freshmaker passed register test
Module 0: Installed -- AUTO FXS/DPO
Module 1:
2005 Sep 07
1
TDM400P not detecting hangup and not hanging up.
Can anyone suggest where I might begin looking for an answer please?
I have just installed a TDM400P (2x FXS and 1x FXO modules installed)
The first problem is that it does not seem to be able to detect if the
remote party has hung up when a call comes through on the FXO. For example,
if someone calls in, and then hangs up at any time after it starts ringing,
Asterisk carries on as though the
2005 May 11
0
softphone buzzing
I am running Asterisk on our LAN with Cisco IP phones and softphone clients,
SJPhone and Firefly. Everything on our LAN works fine and the quality is
good. We have recently registered other callers not on our LAN who are
using SJPhone and Firefly as well. The audio quality is fine, but I
consistently hear a buzzing sound in the background. We have experimented
with the line in and microphone
2008 Sep 05
1
dahdi & tdm400p: no luck
As best i could figure it out, I've installed dahdi and rc4.
My TDM400P doesn't answer fxo or fxs.
/etc/dahdi/system.conf:
loadzone = us
defaultzone=us
fxoks=1,2
fxsks=4
/etc/asterisk/chan_dahdi.conf:
[house-phones]
context=internal ; Uses the [internal] context in extensions.conf
signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel
dahdichan => 1 ;
2008 Jan 02
5
Missing "zap" command in Asterisk 1.4.16
Hi list,
I've just compiled and installed Asterisk 1.4.16 and when I try to run "zap
show" I get the message "*No such command 'zap show'*".
I have a Sangoma Remora A400D with 2 FXS / 10 FXO ports, I've installed the
latest wanpipe too.
zaptel-1.4.7.1 was compiled from the wanpipe installation, so I don't know
what's happening here!!!
Any ideas???
2005 Aug 06
4
TDM400P - All extensions have same CallerID
I've been searching the forums and on the list to see if this has been
addressed. If it has, could someone point me to the thread to fix or at
least acknowledge it is an issue and what is causing it. Posting to the list
was last resort as I couldn't find a solution anywhere else.
Setup:
Asterisk@Home 1.3 (this is my first system, so path of least resistance)
Digium TDM400P (2 FXS on ports
2003 Jul 13
1
Setting up A TDM400P
Hi,
I am having some trouble getting a TDM400P working, and would be very
appriciative of some ideas.
I have installed a TDM400P, and downloaded the appropriate files from CVS,
compiled, installed and modprobe'd the devices.
2003 Jul 31
1
Zaptel cards, working FXS and SIP, no audio?
Greetings again all,
With the help of another list member I was able to get the my TDM400P
card working properly (and the PRI card loaded too for channels 1-24).