similar to: T100P specs

Hi anyone have a idea for debug my digium TE405P card ? My zaptel.conf: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone = fr defaultzone = fr My Zapata.conf: [channels] language=fr context=from-E1 switchtype = euroisdn pridialplan = unknown signalling = pri_cpe usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes

Hi I got the 2nd Gen firmware upgraded on the TE405P. I recompiled after putting in the upgraded board but did not change any conf, but the spans become active but will not come up. I guess I am missing something or are the any changes to the zaptel/libpri software that is required. I cannot find any info about this or does this new firmware only work with latest CVS. I am using 1.0.9 with

Dear users: I have bought TDM04B card and it works in PCI 2.2 ver. slot. How can I check if specific mother board support PCI 2.2 ver. I do not have any documentation for that motherboard. B.

Hello I just updated the kernel, dahdi-linux and dahdi-tools Im also using now asterisk 1.4.26.1 And im still with a red light (not RED/YELLOW anymore): [root at catumbela ~]# /etc/rc.d/init.d/dahdi status ### Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER) HDB3/ RED 1 PRI CAS RED 2 PRI CAS RED 3 PRI CAS RED 4 PRI

I've seen this consistently on three systems, with three different cards, and multiple versions of DAHDI. At first I thought the issue only occurred on newer, Nehalem-based, systems, but I reproduced it on a Core 2 Duo box as well. I've tested with dahdi-linux 2.2.0.2, dadhi- linux-complete 2.0.0+2.0.0, 2.1.0.2+2.1.0.2, and 2.2.0.2+2.2.0. The card is a Digium TE220B which uses the

Hello to all I'm using asterisk 1.4 and dahdi. I had everything working fine, and I could place calls through my R2 channel. But now the channel is always "RED" and Im getting this error message: TE4XXP: Version Synchronization Error! Here is my chan_dahdi.conf------------------------------ [channels] language=en context=incomingr2 signalling=mfcr2 mfcr2_variant=ar

Hi, I'm looking into support for SS7 and I found an article (http://www.openss7.com/news13022002.html) which says that OpenSS7 supports Linux Support Inc's T400P-SS7 Quad T1 and E400P-SS7 Quad E1 PCI interface cards. It also says that Linux Support Inc is the primary sponsor of Asterisk. However I cannot find these cards on the Asterisk hardware page

Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards

I'm trying to install a TE410P this is what happens with compiled zaptel 1.0.9, 1.2-beta and 1.0.9 from http://updates.xorcom.com/iso/ this is my zaptel.conf (checked with the provider the values): span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone=it defaultzone=it then I modprobe wct4xxp debug=1 t1e1override=15 and the kernel says : Sep 30 16:12:40 localhost kernel: Zapata

OK, got a question on 911. Looking into setting up a couple asterisk servers at a country club, with VOIP phones in each of 100 short-term residential rental units. Approx 100 extensions, approx 24 outside lines. Since everything is geographically at one location, reaching 911 correctly shouldn't present a problem. However, the club wishes to ensure that 911 authorities are able to identify

Hi, Can someone point me to a zapata.conf example that will create a single DIAL OUT group including all 4 spans on a TE4XXP? One friend says to change the group number all to "1" on all 4 spans. Another suggestions says it is possible to have these unique groups (1-4) and to combine all 4 into a single group "5". I like the second suggestion best. Can you guide me to the

Hello Asterisk community, I'm experiencing some problems with a Digium TE4XXP, the thing is that i'm sharing IRQ with some megasas device: 169: 69917985 0 0 0 0 0 0 0 IO-APIC-level megasas, wct4xxp I've been searching here: http://ubuntuforums.org/showthread.php?t=254623 Should i try in the pass this parameter in the

I have two sacrificial lambs -- one is an SMP box, the other one''s a laptop, but I don''t see kernel-smp or kernel-pcmcia-cs packages. So, can I use the ext3 patch on an SMP box or a laptop? -- Sam

Hi, all Did anyone tried TDM400 card on old main board (Intel 440LX chipset -- PII)? The reason I am asking is because TDM400 needs PCI2.2 and main board is PCI2.1 I do not want to upgrade yet. Thanks, Rudolf

I have the following software installed in a Centos Box with a TE420 (5th Gen) card. . Centos 6.5 64-bit . Asterisk 1.4.22 . dahdi-linux-complete-2.9.1.1+2.9.1 . libpri-1.4.14. Even without plugging in the ISDN into span 1, all 4 spans are flashing red. Plugging an E1 into span 1 makes no difference. My system.conf is just simply: loadzone=au defaultzone=au span=1,1,0,ccs,hdb3,crc4 bchan=1-15

Hi, I am about to pull my hair out after trying to get our PRI up and working. We are switching from a Cisco gateway to an Asterisk box which provides the 23 phone lines for our office. So, because the Cisco gateway is working I can assume I have all the settings right (b8zs, esf, dms100, etc) and the PRI is live (because we are switching over). When dialing from PSTN, I get busy signal. When

Hi, I'm having problems with a TE420P card, in which I cannot make calls using spans 2 through 4. After a couple of days of working correctly, spans 2, 3 and 4 start failing (can not make calls). The system is configured to work with SS7. After the ACM message goes out, immediately a REL message is returned. I searched for error messages in /var/log/messages and could not find a clue

On a zaptel TE410p, when a call is bridged PRI - PRI how much involvement does the processor have? We're now seeing chunks of missing audio and I can't tell whether this is due to a kernel upgrade or to a zaptel/libpri/asterisk upgrade. I'm not seeing missed interrupts (from a cat of the proc/zaptel files), any other ideas on how I could go about tracking this down? I'm

Group Can I have 2 wildcard T1 cards in the same box? I was thinking the first card would have channels 1-24 and the second card would have 25-48 Does this sound correct?

Can anyone tell me the features of the Cisco 7905 with SIP? I mean things like number of lines, speakerphone, transfer buttons, etc. I've seen the Cisco material, but all it told me was how nifty it is and how wonderful the XML interface will be ;) Thanks, --Ernest