similar to: AVM C4 with Asterisk in front of an ISDN PBX

Hello, I've been using * for quite a while using AVM C4 card and a few Grandstream Budgetone 102 hard phones plus couple of HandyTone 286. Echo is a big problem. I am getting used to it, but some users complain. Anyone has experience w/ regards to echo comparing the AVM C4 with two HFC-cards? Before shelling out time and money, maybe someone else already has done so, and could tell me if

Hi guys, I'trying to setup Asterisk with an AVM Fritz PCI ISDN card with no success. I have an IP phone from Micronet and I want to receive and place calls over ISDN. But I'm not sure if I need the binary CAPI from AVM or isdn4linux. I've tryed with redhat 9 and with Suse 8.2. Cold someone help me? Thank you very much.

Hi! I'm goining to connect an AVM C4 to 4 BRI-lines in PTP-Mode, all BRI-lines will have the same number (1234-XX for example). I don't know if this is possible and I can't test it, because I don't have these lines yet. Is anybody out there, running such a configuration? I'm looking for some example configs. Especially I want to know how it is possible, to let asterisk

Has anyone a working /etc/asterisk/capi.conf example for Germany or Switzerland using the AVM C4 - ISDN Card. I try to connect asterisk to 3 wires BRI-ISDN (Swisscom). I appreciate your help and it would save me a lot of time, figuring it out by myself. regards, Claudio

Hi, Has anybody used AVM C1/C4s on Asterisk? What's the result? I know there may be better cards, but I have 2 C4s which I want to put to good use. Andrea Coppini +356 79 ANDREA (263732) andreacoppini@iwg.info EMPOWER PEOPLE - THE WORLD IN YOUR HAND iWG (iWORLD GROUP) is a global e-mobile company creating, building and growing new businesses. iWG founders are pioneers in creating

Hello, Is it possible to use * as a gateway in the following setup: LAN (with Windows NT/Linux PCs) | Ethernet (IP) | Linux PC with * and AVM Fritz! ISDN Adapter | ISDN | Someone with a analog/digital phone (POTS) Basically, people sitting on their PCs will wear a headset, and whenever they want to call someone,

I have a problem trying to install two avm fritz cards on one asterisk machine. I am using fcusb2 driver. 1 card works perfectly. I tried to recompile driver like it is described on this page but with no success. http://www.quiss.org/caiviar/Two-Fritzcards-HOWTO I think the problem is that i can not find this part of code. dev = pci_find_device (AVM_VENDOR_ID, AVM_DEVICE_ID, dev); if

hello! I'd like to use my asterisk-box on a p2p-line from my alcatel pbx. isdn4linux and capi works fine on a s0-line from the pbx, but i need more then 8 msns, cause i'd like to implement a voice-mail system and an extension to our "old" pbx with voip-phones. had anyone success using isdn4linux on a t0 (p2p) line (of course with an inexpensive passive card like my avm

Hello everyone, I have Asterisk SVN-trunk-r7498 installed on a server (celeron 2.4 Ghz, 256MB) with a TDM40b a TDM04b and an avm fritz!card pci. I experience a problem with voicemail: my messages are good unless the incoming call comes from isdn, which means via the avm fritz!card. In this case (and in this case only) the message is disjointed and I can hear at most 1 second out of a 1 minute

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi there, i'm in debian sid 3.1 with kernel 2.6.7, * last cvs & chan_capi 0.3.4b; nt1+ with 2 bri in ptmp (http://www.voip-info.org/tiki-index.php?page=DDI) i tried to install avm c4 following step by step http://www.voip-info.org/tiki-index.php?page=Asterisk%20How%20to%20connect%20with%20CAPI step 1. i compiled capi 2.0 support in kernel

Hi *, This is my first message to this list, so I hope I am not breaking any rule with my post. My question is the following: can I establish a voice connection over an ISDN interface by using a bluetooth dongle to connect to the ISDN access point? Here follow the details: I have compiled and configured asterisk. Everything seems fine except that when I configure asterisk to use the ISDN

Thanks to "WipeOut" who told me how to install the AVM fritz card. I think asterisk is working, no errors or warning by starting asterisk. Now I'm in trouble with the configuration files. I want to place calls over the ISDN network using an IP phone from Micronet. How can I setup the system? Thanks everybody who can help me.

Hi, i want forward a call witch is comming over isdn (avm b1 witch i have) out to isdn (same card 2. b channel). The call is comming (one b channel open one is free) the forwarding is processed (snom 200) all seems correctly. Then the message that the b channels all busy, but so is it not. Forwarding to a sip phone works. Can anyone help me with that ? nicolas SNIPS: ------ ==

I have an asterisk installation connected to 2 isdn lines via an AVM C2 card. modules seems to load well, lsmod gives : c4 19588 4 b1 24192 1 c4 capidrv 28468 2 isdn 134604 9 capidrv slhc 7552 1 isdn capi 18112 4 capifs 6024 2 capi kernelcapi 46112 4

Hi All, Has anyone had success with using the AVM Fritz PCI ISDN Card (v2) CAPI drivers with a distro other than suse? The AVM driver is geared towards suse, and after trying them with RedHat 9 I've not got very far. The module compiles but dies when I attempt to modprobe it. I've googled until I almost lost the will to live! What little information I can find seems to refer back to

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Not strictly Asterisk related, but I'm trying to get an AVM Fritz! card to work with Asterisk on a Fedora Core 3 box. I've grabbed the official AVM Fritz CAPI driver from the AVM website and compiled against the current kernel. However, as soon as I modprobe it I get: CAPI Subsystem Rev 1.1.2.8 fcpci: module license 'Proprietary'

Hello, I have been wrestling with installing the CAPI drivers for AVM Fritz in order to use chan_capi with Asterisk. I use an SMP machine, RH 9. I have found rpm's for CAPI and AVM drivers (namely: capi4k-utils-2003.06.16-08.mungo.RH9.i686.rpm and kernel-2.4.20-8- avmfcpci-03.11.02-08.mungo.RH9.i686.rpm), but I believe that they support only single processor machines. I've already

Hello asterisk-users, I recently set up an asterisk server using Debian Sarge. I also added an ISDN card (AVM FritzCard PCI) to the machine. I built amd installed a new kernel (2.6.15.1) with modular support for the CAPI stuff and also integrated the FritzCard driver available from AVM. capiinfo succeeds in correctly showing the ISDN card. When talking from one PC to another via SIP, everything

Hi, i will use an AVM C2 controller with asterisk. How can i use both card ports ?? On the voip-info.org Wiki is only notice to: You will need a section for each controller in /etc/asterisk/capi.conf so the C2 will have 2 sections. But how is look like this ? Only on the first port is asterisk assume connections, but nothing on the second card port. In the dmesg is only the capidrv-1 shown,

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk