similar to: E100P configuration

Hi, I have two E100P boards connected to my PC. I wish to setup two E1-ISDN-PRI lines, the first SPAN with 15 channels and the second one with 30 channels. When I try to load zaptel modules, I get an error message: "Loading zaptel framework: Loading zaptel hardware modules: wct1xxp wcusb Running ztcfg: ZT_CHANCONFIG failed on channel 63: No such device" Follows my zaptel.conf:

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

Hi, i just received an E100P, this is the first one I have ever seen, and notice that the board reads T100P. Is this right ? The antistatic bag had a small label that has E100P written on it, and the card is a bit different than the T100P I already have, Does Digium use the same boards for both cards ? I don't have an E1 link here, can I test the card just by loading the driver and run

Hello ml, i need some help on my zaptel configuration. My E100P only shows some YELLOW / RED alarm when I load the wct1xxp module and do a cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS YELLOW RED ... .. . My /etc/zaptel.conf is: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=nl defaultzone=nl I tried zaptel-1.0RC2 and the latest CVS

hi see below's conversation. it seems the e100p card doesn't work with BT. Any idea how this'll work against Telenor (norway)? roy <RoyK> does anyone know if I can trust the E100P to do full PRI stuff in .no? <cypromis> dunno about no <cypromis> I cannot use it in UK <cypromis> cause the framer has problems with system-x switches at bt

Just cross pairs 1-2 and 4-5 1 <--> 4 2 <--> 5 Never done an E1, but I think it's the same for a T1 4 wire cable. Tim Thompson Commercial Sales Engineer http://www.amatechtel.com (806) 722-2227 -----Original Message----- From: bam [mailto:bam@cqm.co.uk] Sent: Monday, December 29, 2003 9:12 AM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] E100P pinouts

Hello, I have a E100P card from digium and I try to implement a conference bridge in asterisk. I wonder since I got the E100P card do I still need to load ztdummy for caller from h323 endpoints to work with Meetme? I load the E100P driver but i did not load the ztdummy driver. My h323 caller does not hear any voice play by Meetme. Looks like ztdummy is required as long as h323 is concern and

hi All, quit new to asterisk, can anybody tell me whether Wildcard E400P and Wildcard E100P support R2 CAS protocol. if they do, what is the value, i should set to 'signalling' parameter in the zapata.conf file? Surajee -------------- next part -------------- An HTML attachment was scrubbed... URL:

All, I'd like to buy an E100P Wildcard frm Digium, but i prefer to buy it in Europe (costs, ...). Could somebody point me to an european reseller ? Thanks in advance. -- Nicolas Cartron nc@ncartron.org

Hi, I am running * with E100P board. At least every our I got an Error 500 message and ISDN-PRI restarts: Jan 10 12:53:02 WARNING[98311]: File chan_zap.c, Line 5758 (zt_pri_error): PRI: Read on 27 failed: Unknown error 500 Jan 10 12:54:27 WARNING[98311]: File chan_zap.c, Line 5758 (zt_pri_error): PRI: Read on 27 failed: Unknown error 500 Jan 10 13:33:01 WARNING[98311]: File chan_zap.c, Line

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

Hi, I'm installing my first E100P. My zaptel reads the following: Span=1,0,0,ccs,hdb3,crc4 E&m=1-31 My Zapata.conf reads the following: Signaling = em_w Channel =1-15 Channel =16-31 After starting the zapter service I get: ZT_SPANCONFIG failed on span 1: No such device or address (6) ??? PauloHM -------------- next part -------------- An HTML attachment was scrubbed...

I've seen this question asked before but haven't seen a definative answer. Does the e100p work in australia? Did any one who was asking the question before bite the bullet and get one? I can get a te410 if i really have to but would prefer to stay with the cheaper option. Any comments appreciated, Thanks ------------------------------------------------- This mail sent through IMP:

Hi, I have a query from a client that can he use the E100P card to terminate the 2Mbps bandwidth in a linux box, thus reducing the cost of cisco router ?? The other end is a cisco 2620 router with E1 VWIC-1MFC. Can anyone explain if its possible with Asterisk and further any configuration help. Applreciated. Regards Azher Amin ------------------------------- http://www.consulttech.com.pk

hi guys, I have a little problem maybe you can help ... I have an asterisk setup, with an E100P, and an ISDN-PRI 30 channel line from the telco going into it .. the E1 line is OK, because plugged into a Lucent Portmaster 4 it works OK .. plugged into the asterisk box I just get an engaged tone, and asterisk posts this message on screen : WARNING[1167272000]: File chan_zap.c, Line 5275

Hello list, i've got some problems getting a E1 line with a E100P up and running (germany). # cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS/CRC4 YELLOW RED "YELLOW RED" sounds not so good. When launching asterisk, enabling pri debug on that span, i see outgoing attempts: ;---------- snip -------- > [00 01 7f ] > Unnumbered

Hi, all I am trying to install E100P card, the 'modprobe zaptel' is ok, but when I did 'modprobe wct1xxp', I got such error, so can not load the driver for the card. /lib/modules/2.4.20-8/misc/wct1xxp.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog

Chris you might know the answer to my HUUUUUUGE problem A few weeks ago you posted this message: "I have an ISDN PRI supplied by NTL (ex Diamond Cable, Nottingham) which is currently working happily with an SDX Index phone system. I have to replace this phone system shortly and I've been trying to get a * system working for some weeks now. I have configured the dial plan (which works)

Has anyone made spandsp to work with a digium tdm fxo card? I finally got the rxfax and txfax modules to compile, the spandsp lib installed (and in the libpath), and now receive: -- Starting simple switch on 'Zap/1-1' -- Executing RxFAX("Zap/1-1", "/var/fax.tif") in new stack -- Hungup 'Zap/1-1' I've tried to adjust rxgain/txgain in

Hi, I'm having trouble configuring and E1 link , I know the E1 is a PRI and the switchtype is 5ess. The problem is that everytime I try to dial I got and error saying that it was unable to open the zap channel . Devices are created in the /dev/zap directory and I can open them with a cat /dev/zap/1. I can also see the channels in /proc/zaptel/1. Thanks in advance [zaptel.conf]