similar to: E100P pinouts anyone?

Hi, all I am trying to install E100P card, the 'modprobe zaptel' is ok, but when I did 'modprobe wct1xxp', I got such error, so can not load the driver for the card. /lib/modules/2.4.20-8/misc/wct1xxp.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog

Hi All, I wish to connect * to a Cisco using a E100P board. When I load the driver I got this error message: -bash-2.05b# modprobe wct1xxp ZT_CHANCONFIG failed on channel 1: Function not implemented (38) /lib/modules/2.4.21-SAX/misc/wct1xxp.o: post-install wct1xxp failed /lib/modules/2.4.21-SAX/misc/wct1xxp.o: insmod wct1xxp failed Follows Cisco configuration: isdn switch-type primary-qsig

Hello ml, i need some help on my zaptel configuration. My E100P only shows some YELLOW / RED alarm when I load the wct1xxp module and do a cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS YELLOW RED ... .. . My /etc/zaptel.conf is: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=nl defaultzone=nl I tried zaptel-1.0RC2 and the latest CVS

Hi, i just received an E100P, this is the first one I have ever seen, and notice that the board reads T100P. Is this right ? The antistatic bag had a small label that has E100P written on it, and the card is a bit different than the T100P I already have, Does Digium use the same boards for both cards ? I don't have an E1 link here, can I test the card just by loading the driver and run

We connected an * box with an e100p to an E1/PRI from a telco here in Italy. After we had it working perfectly the telco told us that, despite the circuit appeared to work fine, and we could place calls on it, they had an "E-bit2 alarm indication constantly on that caused the circuit to be flagged as "faulty" every time. (The E-bit indication, is an alarm sent back from us to

Hi, I have two E100P boards connected to my PC. I wish to setup two E1-ISDN-PRI lines, the first SPAN with 15 channels and the second one with 30 channels. When I try to load zaptel modules, I get an error message: "Loading zaptel framework: Loading zaptel hardware modules: wct1xxp wcusb Running ztcfg: ZT_CHANCONFIG failed on channel 63: No such device" Follows my zaptel.conf:

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

Hi, I'm installing my first E100P. My zaptel reads the following: Span=1,0,0,ccs,hdb3,crc4 E&m=1-31 My Zapata.conf reads the following: Signaling = em_w Channel =1-15 Channel =16-31 After starting the zapter service I get: ZT_SPANCONFIG failed on span 1: No such device or address (6) ??? PauloHM -------------- next part -------------- An HTML attachment was scrubbed...

Hi- Anyone using the Junghann's quad BRI card and the Digium E100P in the same system? I'm having a configuration problem where I can configure the cards one at a time (with the appropriate drivers loaded) in a system, but when I try them both together, neither will work. They both work fine one at a time. Probably has something to do with the channel numbering. I've tried

Hi, I buyed a wildcard e100p and I installed that but when I load asterisk I have this error: Apr 29 18:59:25 WARNING[8192]: chan_zap.c:690 zt_open: Unable to open '/dev/zap/channel': No such device Apr 29 18:59:25 ERROR[8192]: chan_zap.c:5403 mkintf: Unable to open channel 1: No such device here = 0, tmp->channel = 1, channel = 1 Apr 29 18:59:25 ERROR[8192]: chan_zap.c:7526

Hi, I try to connect my asterisk box with a classic pbx (Siemens). I have a T100P E1 card. modprobe zaptel and wct1xxp ok ztcfg -vv ok I can run asterisk and show the channels but the led still flash red My zaptel.conf : span=1,1,0,ccs,hdb3,crc4 bchan=1-15 bchan=17-31 dchan=16 My zapata.conf : ;; E1 switchtype = euroisdn signalling = pri_net group = 1 context=e1 channel => 1-15,17-31

Hello I have installed my new E100P card in the same machin with two TDM04B cards. I have followthe instructions on http://www.digium.com/index.php?menu=configuration#T_E100P_PRI This is my zapata.conf span=1,0,0,cas,ami fxsls=1-15,17-31 dchan=16 fxsks=32-39 loadzone = us defaultzone=us I do *modprobe zaptel wct1xxp wcfxs ans seems to work ok. * But when i do ztcfg -vvv i got Zaptel

Hi! I have just bought the X100P and TDM400P cards to install on my computer to implement the PBX. I also downloaded the newest softwares asterisk_ver0.5.0, libpri_ver0.4.0, and zaptel_ver0.7.0) to install on my computer (Red Hat Linux 8.0). All packages are compiled well. When I use "modprobe" to load drivers (modprobe zaptel, modprobe wcfxo, modprobe wcfxs), the first two (zaptel,

hi see below's conversation. it seems the e100p card doesn't work with BT. Any idea how this'll work against Telenor (norway)? roy <RoyK> does anyone know if I can trust the E100P to do full PRI stuff in .no? <cypromis> dunno about no <cypromis> I cannot use it in UK <cypromis> cause the framer has problems with system-x switches at bt

Hello, I have a E100P card from digium and I try to implement a conference bridge in asterisk. I wonder since I got the E100P card do I still need to load ztdummy for caller from h323 endpoints to work with Meetme? I load the E100P driver but i did not load the ztdummy driver. My h323 caller does not hear any voice play by Meetme. Looks like ztdummy is required as long as h323 is concern and

Hi All, This is our 2nd E1 client that we try to use crc4 either with the e100p or with the e405p without luck. After some trials, we ask the telco to switch off crc4 on their side and everything works flawlessly. Is there anything in the crc4 calculation that may be broken? We took a look at wct1xxx.c and wct4xx.c but there doesn't seem to be much there to be fixed (apparently the crc4

Hi, We currently have an Asterisk box (P4 2.4 Ghz, 512Mb RAM, 1 T100P, Zhone Channel Bank and 1 E100P) connected to an ISDN running without any problems. That machine is working for about 1 year. Two days ago, we decided to switch that machine for two PowerEdge 600SC (HA) and we got some problems. The running machine (P4 2.4Ghz) has an Intel motherboard with four 32-bit 3.3v PCI slots,

Hello list, i've got some problems getting a E1 line with a E100P up and running (germany). # cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS/CRC4 YELLOW RED "YELLOW RED" sounds not so good. When launching asterisk, enabling pri debug on that span, i see outgoing attempts: ;---------- snip -------- > [00 01 7f ] > Unnumbered

Hi ! I am trying to configure two E100P cards, but I am a bit confused with zapta.conf in what I am trying to achieve. The * will be connected to a pstn switch with two E1 PRI lines. The E1 lines will be used for incoming calls as well as outgoing calls. My problem now is what to put in zapta.conf, I would like to group all channels from both cards together (if that's possible). Does this

hi All, quit new to asterisk, can anybody tell me whether Wildcard E400P and Wildcard E100P support R2 CAS protocol. if they do, what is the value, i should set to 'signalling' parameter in the zapata.conf file? Surajee -------------- next part -------------- An HTML attachment was scrubbed... URL: