similar to: Configuring new system for a non-profit organization

Hi, Maybe someone has seen this before... I've installed a new T100P, but it doesn't seem to work. I've attached the T100P to an Adtran 750 using a crossover cable. The Adtran shows a red alarm on the T1 interface. The Adtran has been set to factory defaults with FXS cards in 1-3 and an FXO card in 5. The T100P shows no signs of life--the leds are not lit. Should I be seeing

What they are probably marketing is putting in their own equipment out there. I install a product that does exactly that. A paradyne jet fusion. It takes care of the part of which channels are data and which are voice. If it's anything like these, the lines will come out on pairs. You will then have to use channelbank and FXO/FXS cards to get it into your phone system. The jet Fusion

I went on a service call yesterday to find an asterisk system with a T100P card on a Qwest PRI and a TDM40B card connected to fax machines. The TDM40B LEDs were not lit, and the system did not respond to keyboard input. However, calls were being processed for the PRI and 7960 phones. I replaced the TDM40B card with a new one, and the system now seems to be ok. But I'm wondering, why

We have contracted with Eschelon to provide voice and data over a T1 link. The plan is to terminate this link at a T100P card in the * system. The vendor has said that they will provide the D channel "contiguous to the voice channels" (voice on channels 1-8 and D channel on 9). The data channels would be 20-24. Will the T100P be able to accept this configuration? Does the PRI

My CLEC just called and asked if we will support the "MI2" protocol on our proposed T1 circuit. I think this is for CallerID name. Will the T100P support this? Thanks, Mike

I'm about to install a second T100P card in my asterisk system, and now I'm wondering how the system determines span-1 vs span-2. Does the position on the PCI bus determine this? TIA Mike

Hello, I am connecting Asterisk to an Adit 600 via a T100P. Unfortunately I am not able to get any lights on the T100P and the Adit 600 only shows red. I have already modprobed the t100p. Has anyone successfully connected these before? I've tried both a cross-over cable and a standard cat 5 cable, but I can't seem to get them to work. Any suggestions? Thanks! Craig

I'm debugging a TxFax problem whereby the fax transmission fails. I suspect interrupt latency--some interrupt routine is holding its interrupt too long. I have all unnecessary services switched off and X is not running when I perform these tests. Some transmission are successful while others fail at random points. I've noticed that after I boot Linux, load zaptel, wcfxo, and wcfxs,

Hi, My PBX/key system failed when building power was switched off and then back on. The service rep says the PBX unit is so old that it is not repairable. The unit has 8 incoming POTS lines and 12 multiline sets. There are voice mailboxes on each line. Switching to Qwest's Centrex system would cost about $3800/yr. My 8 business lines now cost $3320/yr, so the Centrex increment would

Does anyone have any recommendations for overhead paging systems for use with Asterisk? Thanks, Randy Johnson -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031113/82ae09ec/attachment.htm

Has anyone had any experience connecting Asterisk to Cbeyond's SIPconnect service (http://www.sipconnect.info)? Any opinions? Thanks, -Brian

Hello all, My set up is a fractionated t1, with 1-6 voice channels, 21-24 data channels. I have a t100P installed in a amd 1500 with 512meg. Question: In order to set up the data channels, is the following correct? 1) compile new kernel with generic hdlc support 2) compile hdlc from hq.pm.waw.pl/hdlc 3) uncomment KFLAGS+=DConfig_ZAPATA_NET in zaptel makefile 4) compile zaptel, 5 compile rest

Hello, I'm running Fedora Core 3 with udev, and asterisk/zaptel/libpri from cvs. I have followed the README.udev instructions replacing insmod with modprobe and rmmod with modprobe -r and adding the 60-zaptel.rules file, yet no matter what I do I still get this error on boot(or when I run service zaptel restart): [root@pbx ~]# /etc/init.d/zaptel restart Unloading zaptel hardware drivers:

Hi, For MGCP users. Is there any success stories with any MGCP IAD vendor. I?m trying to find an IAD which works with Asterisk. I?ve tried the Cisco IAD 2430 without success; but SIP on this IAD works but it?s limited (no authentication, no notify messages, etc) and with higher density IAD (16 or more ports) it?s nice to control using MGCP. Any information will be apreciated ! Thanks. --

Hi- I have an upcoming order for a bunch of asterisk boxes, and I'm considering using an "assembled" package for the server, instead of building them from components as I usually do. Does anyone have experience with the Dell PowerEdge 750 server, or any other 1U rackmount server for use with asterisk? Thanks in advance Scott Stingel Scott M. Stingel President, Emerging Voice

I'm having difficulty with an Asterisk system. The external party has very good call quality, but the internal party hears clipping and drop outs. The WAN comes in from the Cisco IAD and into a LAN switch (DLink DGS-1005D w/ 802.1p) where the two public IPs are switched to different devices. One device is a FireBox device controlling a separate LAN with VPNs. The other device is eth0

I'm considering switching my incoming phones lines from standard analog to a T-1 service from XO communications. They propose to bring in an "IAD" which has 12 lines of voice and 768k of internet bandwidth as part of a package deal. Since I want to keep the voice traffic in the digital domain the equipment they're proposing is a "Lucent Digital Vina Integrator" IAD

WPLink is a non-profit organization that want to help a group of amateur radio people and other poor people that want to learn PHP or mySQL. WPLink will be going through some updates in the next months. For the upgrade to happen, we need to raise a certain amount of money, since we personally cannot and do not have the necessary funding. I have all hardware without this items, that badly needs

I repost a message I put a week ago: I have a Cisco IAD 2431 which has MGCP protocol; I cannot make it to work againts Asterisk; at least there is some MGCP conversation between them but when I offhook a phone attached to IAD I get no tone at all. As anybody managed to get working Asterisk against an MGCP Cisco gateway ? Which MGCP version should I use ? Also I recently

On 10/19/2016 01:54 PM, m.roth at 5-cent.us wrote: > Alice Wonder wrote: >> On 10/19/2016 11:34 AM, Leonard den Ottolander wrote: >>> Hello Gordon, >>> >> *snip* >>> >>> Personally I would be more concerned whether or not to enable ECDSA >>> algorithms (https://blog.cr.yp.to/20140323-ecdsa.html). >>> >> For web server ECDSA