Hi, For MGCP users. Is there any success stories with any MGCP IAD vendor. I?m trying to find an IAD which works with Asterisk. I?ve tried the Cisco IAD 2430 without success; but SIP on this IAD works but it?s limited (no authentication, no notify messages, etc) and with higher density IAD (16 or more ports) it?s nice to control using MGCP. Any information will be apreciated ! Thanks. -- Juanjo sin .sig
Hi, A colleague of mine used Dlink DS-104S with good success. Peter At 02:14 6/12/03 -0300, you wrote:>Hi, > > For MGCP users. Is there any success stories with any MGCP IAD > vendor. >I??m trying to find an IAD which works with Asterisk. I??ve tried the >Cisco IAD 2430 without success; but SIP on this IAD works but it??s >limited (no authentication, no notify messages, etc) and with higher >density IAD (16 or more ports) it??s nice to control using MGCP. > Any information will be apreciated ! > >Thanks. >-- >Juanjo sin .sig > >_______________________________________________ >Asterisk-Users mailing list >Asterisk-Users@lists.digium.com >http://lists.digium.com/mailman/listinfo/asterisk-usersPeter Brown CEO IP Telephonics
> Message: 7 > From: "Juan J. Sierralta P." <juanjo@atmlab.utfsm.cl> > To: Asterisk Users <asterisk-users@lists.digium.com> > Organization: Telefonica CTC Chile > Date: 06 Dec 2003 02:14:22 -0300 > Subject: [Asterisk-Users] MGCP IADs > Reply-To: asterisk-users@lists.digium.com > > Hi, > > For MGCP users. Is there any success stories with any MGCP IAD vendor. > I??m trying to find an IAD which works with Asterisk. I??ve tried the > Cisco IAD 2430 without success; but SIP on this IAD works but it??s > limited (no authentication, no notify messages, etc) and with higher > density IAD (16 or more ports) it??s nice to control using MGCP. > Any information will be apreciated ! > > Thanks. > -- > Juanjo sin .sig >Using Askey and they seem OK, not in a production environment though. darren
I am new to * and after getting some much needed help from someone on the IRC channel with my config files I got my system up and going. I have several dlink DG 104s's and they seem to work fine on my LAN the only trouble I have is trying to get them to work thru double Nat by that I mean on both ends. My * box is behind Nat and I am trying to setup a 104s at another location behind Nat no luck so far but I will get it somehow. I have read in the lists that they loose their config but I have not had that trouble the only advice I have is if you upgrade the firmware reset to factory default after then configure the units with a serial cable James Schenck Egraph Design Inc. Arkansas Online Internet Services (870) 857-3287 IAXTEL(700) 857-3287 jims@egraphdesign.com -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Juan J. Sierralta P. Sent: Friday, December 05, 2003 11:14 PM To: Asterisk Users Subject: [Asterisk-Users] MGCP IADs Hi, For MGCP users. Is there any success stories with any MGCP IAD vendor. I?m trying to find an IAD which works with Asterisk. I?ve tried the Cisco IAD 2430 without success; but SIP on this IAD works but it?s limited (no authentication, no notify messages, etc) and with higher density IAD (16 or more ports) it?s nice to control using MGCP. Any information will be apreciated ! Thanks. -- Juanjo sin .sig _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users