similar to: MWI and SNOM 200

Long story short... Snom's ... Retrieve button... works when MWI is *NOT* lit but does *NOT* work when it is lit. Any advice Useragent : snom360/6.5.2 Function: F_RETRIEVE [root@pbx ~]# asterisk -rx "show version" Asterisk 1.2.13 built by root @ pbx on a i686 running Linux on 2006-11-17 16:35:22 UTC [gateway] exten => 201,hint,SIP/201 exten =>

Dear List, I'm having a blinking MWI light on the snom 320 even when there's no message waiting in Asterisk. We've managed to make the voicemail button work using fromdomain=192.168.0.1 in sip.conf vmexten=2500 (our VoicemailMain application extension in extensions.conf). We also added notifymimetype=application/simple-message-summary also in sip.conf to allow SIP simple MWI

Hi, I found some issues with Snom 320 message retrieve key. This button works only when the MWI does not blink! If MWI blinks and I do press retrieve button I get "Unknown" on display and busy tone. From the sip debug it looks like that Snom does not send credentials to Asterisk which responds with 407 Proxy Auth required. I have loaded Snom with latest 5 firmware. No change. I'm

Hi, I have VoiceMailMain on extention 1001 so it would be nice to get that sent to the phone instead of asterisk@[IP Address] when there is a message waiting.. Is it possible to change the extention that is sent to the phone when MWI is lit up?? Thanks.. -- ______________________________________________ http://www.linuxmail.org/ Now with e-mail forwarding for only US$5.95/yr Powered by

Hello. I am using a snom 320 running 5.3.6 with Asterisk 1.2.4. In the sip.conf entry, I have mailbox=1234@default and vmexten=*98. The light on the snom 320 turns on when I have voicemail and the retrieve button dials the correct extensions. However, the light turns off immediately after making the call to voicemail, even if I do not check the voicemail. Any idea on how to get this to behave

Hi All I have a snom 200 phone here which works perfectly when using the handset to playback the voicemail messages etc. However when I play back the voice using the speakerphone it sounds choppy. Anyone had this problem before? Regards Mark

I have many remote locations that dial into a central server to retrieve voicemail via IAX. Outbound calls are handled as SIP calls from a Snom to a local (to them) Asterisk server that dials the main server thru IAX. I have trained them to check their voicemail via the emailed WAV file, however some of them are, how shall I put it, idiots*, and insist that they *have* to have the MWI indicator

I have the voicemail setup working in that I get the MWI and it emails the message correctly. When I pressed the MWI button on my SNOM 200, it dials into the voicemail system and prompts me for a mailbox and password. I know there is a way to automatically connect directly into the mailbox via the extension.conf file, but I can not find the documentation I am looking for in reference to variables

Hi All - I'm running version SIP version 1.3.4 on various IP300, IP500, and IP600 Polycom phones. I'm having a tough time with MWI. I thought I remembered somebody on the list saying that they had it working, but I can't find it in the archives now. I have all the phones configured for MWI as specified in the WIKI: ipdmid.cfg: up.oneTouchVoiceMail="1"

Hi, I have more or less decided to do with the SNOM phones for the next stage of testing with Asterisk becasue they seem to be the best value for money and have support for the GSM codec and easy upgrades.. But now I have to decied wheather to get the 100 or 200 and if its the 200 then I need to have some justification for the extra cost.. Can someone who knows these 2 phones tell me what the

Christian, Just a quick heads up warning that something seems to be amiss on the Snom 200 running v2.03h code. The Message Waiting Indicator is blinking (due to a voicemail left in Asterisk) as its suppose to. Some time later the LED stops blinking (as though no voicemail); then later it starts blinking again. I left a voicemail to x3008 (button 2) this morning at 8:48am, and purposefully have

I think I have my echo problem solved, now i need to tackle the MWI. I can't seem to get it to light up. I'm using Asterisk 1.4.14. Here's a section from my sip.conf for my test phone: [general] context=internal allowguest=no allowoverlap=no allowtransfer=yes notifyhold=yes bindport=5060 bindaddr=0.0.0.0 srvlookup=yes pedantic=yes vmexten=9998 at internal ;vmexten=*97

Hello, Does anyone know how to conference a call on the SNOM 200 phone? Whenever I push the cnf/tran button it just hangs up on the active call. The manual says you have to push the cnf function key but it doesn't appear in the lcd on my phone. Thanks -Matt -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi all, Configuration: Analog phone connected to TDM400p. I'd like the phone to give a half-ring (chirp) periodically when there is a message waiting. Can this be done? How is it configured? The visible "Message waiting" indicator and the stutter dial tone are working fine, but are not sufficient for me. Thanks!

I tried to use message waiting indicator, by "Subscribe for MWI" in the web menu of the phone. However, it does not light up / flash, even if a voice mail is waiting. Where is the switch to turn it to? bye Ronald

Sorry for the partial post a moment ago With help I got two phones communicating - PCMA/PCMU was the problem. Next stpe is to try voicemail. VM works fine, I can leave a mesage and then retrieve it - but no MWI on the phone and no stutter dialtone. I promise I've spent the requisite 4 hours + on google etc. but have really no further ideas. The setup is 2 Grandstream phones (latest

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040106/3efdeb9f/attachment.htm -------------- next part -------------- Hello Though my SNOM 200 phone receive a voice mail but it doesn't show MWI on the LCD panel, Instead it keeps displaying "DND SW-REG,Call-log". Though I can access my voicemail using exten

asterisk-users-request@lists.digium.com is believed to have said: >I don't mean to be rude to everyone who responded to this question, but >I think that everyone is answering the wrong question. The point is that >the message waiting indicator doesn't light up, at all, ever. All that >happens when messages are waiting is that the display blinks and the >phone gives a

asterisk-users-request@lists.digium.com is believed to have said: >Budgetone and MWI > >The message button can be programmed to dial an extension that checks >voicemail >exten => 160,1,Voicemailmain(${CALLERIDNUM}) > Thanks, this is what I was thinking about. Still, how do you get the BT to dial 160? In my Asterisk setting I have the same mailbox numbers reused for the

Hello all, Does anyone has experience of deploying Asterisk based VoIP solution in a universitywide campus. We are at present investigating various Soft PBX for this purpose from different vendors Digium,Snom, Pingtel... We are looking at serving more than 5000 clients and we want to be very sure before taking any final decision. I would be glad to hear from members who are aware of