similar to: ISDN (isdn4linux) DDI

hello, anyone has worknig ISDN hfc-pci card in DDI (DID) point2point mode? what kernel ? and second question mISDN driver .. anyone has working solution with mISDN and maybe fritz card? what you suggest for DDI -> point2point mode (card,kernel,chan_..., ...) ? thank you, Tomaz

I'm using a TE405p with all four spans enabled, two configured as pri_cpe and two as pri_net, the asterisk is sitting between our ISDN (UK BT EuroISDN30) and our phone system. We have 200 DDI numbers on the ISDN's and I need to give one of our clients dial-in access to be able to monitor calls we handle on their behalf. I've got ZapBarge working but I need to restrict the client

Hi everyone, I want to get multiple DDI's and hunting across those DDI's in case one of the lines is busy using analog phone lines. The system is for a large house so I want 3 x PSTN lines. 3 x DDI's and the ability for those DDI's to be presented across all three PSTN lines. BT say you can't have more than one DDI number associated with a PSTN line and that you can't

You should be able to get ISDN though. I think BT provide this anywhere. Otherwise your solution will be a Primary rate (ISDN30) with 8 channels. -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Matt Sent: 07 June 2004 10:19 To: asterisk-users@lists.digium.com Subject: Re: RE: [Asterisk-Users] Multiple DDI &

Hi all, Is there in * support for DDI (Direct dial-in)? I buy a AVM ISDN-Controller B1 & I want to use it in point-to-point mode on my ISDN BRI link with DDI preselection. That means, that I have phone number range from ATM, e.g. +421 2 xx xx xx yy where yy I can set-up on my PBX (*) xx - fixed numbers. I want various action for various yy, like (f.e.): 01 -> ring analog phone on TDM

Hello, I am trying to use 2 netjet cards under asterisk and isdn4linux. I am having a hard time trying to get them to work in terms of dial out. Does anyone have a working config I could look at for even one card (tried that, not much luck either). When i dial out: -- Accepting AUTHENTICATED call from 172.16.11.2, requested format = 2, actual format = 2 -- Executing

Hello- I have a system with one D410P and one B200P (both OpenVox). All is well with the D410P, inbound and outbound, and I can initiate calls on the B200P BRI span, but there may be something wrong with my inbound BRI setup: there is no indication of an inbound call when I dial in to it from the PSTN. When I run "pri intense debug" and make a call to the BRI span, I can see a

Hi all ! We have 3 NTBAs which are all going to our existing PBX. Our areacode is 06003 and our DDI enabled number 9141. I want to exchange that PBX with Asterisk, but still struggle to get it working. My CAPI.CONF is currently like this: [general] nationalprefix=0 internationalprefix=00 rxgain=0.800000 txgain=0.800000 [interfaces] context=in-capi msn=60039141 incomingmsn=* controller=1

Hello, we had a running configruation where asterisk passed the phone number and the ddi to the pstn (i.e. 595-431) Now only the rootnumber arrives: 5950 I do not know, what to do. I tried to use callingpres (now i am just hiding every number, because 595-0 is no valid extension..) but that did not worked. > Protocol Discriminator: Q.931 (8) len=44 > Call Ref: len= 2 (reference

Author: pjha Repository: /hg/zfs-crypto/gate Revision: 1384398963b7f0f86003735b23845a984fe75f5e Log message: 6371650 pci capability ddi iterator Files: create: usr/src/uts/common/io/pci_cap.c create: usr/src/uts/common/sys/pci_cap.h update: usr/src/uts/common/Makefile.files update: usr/src/uts/common/io/pci_intr_lib.c update: usr/src/uts/common/io/pcie.c update:

Hi everybody, I have problems with the chan_capi in the P2P (DDI) mode and it is not possible to use zaphfc, because I need call defelction. This is my capi.conf: [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 language=de ;mode=immediate isdnmode=ptp ; 123456 -0 [interfaces] msn=1234560 incomingmsn=1234560 controller=1

I have * configured with 2 X100P cards (fxs_ks). The lines from the telco are 'analogue both way ddi trunks'. This means that every inbound call contains digits that represent an extension on the PBX. I can make outbound calls from * with no problem however I cannot receive inbound calls on these trunks. Some investigation has shown that when the line is idle there is 50 volts present and

Hi, I'd like to know if and how can I set CallerIDNum for outgoing calls on a PRI line with DDI. Does anyone know if italian Telecom permit this? Thanks -- Domenico Viggiani

FYI >Mailing-List: contact vulnwatch-help@vulnwatch.org; run by ezmlm >List-Post: <mailto:vulnwatch@vulnwatch.org> >List-Help: <mailto:vulnwatch-help@vulnwatch.org> >List-Unsubscribe: <mailto:vulnwatch-unsubscribe@vulnwatch.org> >List-Subscribe: <mailto:vulnwatch-subscribe@vulnwatch.org> >Delivered-To: mailing list vulnwatch@vulnwatch.org

If anyone can help me with this I'll be soooo grateful :) We have a isdn30 line, with a DDI range. We also have 2 business units that have separate 0870 numbers that are mapped onto 2 DDI numbers. I would like to be able to present these 0870 numbers from the business units so that the correct number is displayed on a callerid, or when 1471 is dialled. BT claim that I can only have a

Hi everyone I'm interested in using the Telappliant/voip-talk offering as an alternative to my DDI analog problem. (see [Asterisk-Users] Multiple DDI & Hunting on Analog Lines (UK) for details) Does anyone on the list have any recent comments on reliability etc? I would really appricated some positive and negative comments. Cheers Matt

Hi all, I'm looking at my options for getting access to ISDN ISUP fields from DDI numbers, when connecting to a 3rd party Asterisk server. This is for a custom voicemail solution, and at this stage I want to avoid renting a PRI. The information I need to capture is: - Calling Number - Called Number (e.g. the DDI handling the call) - Redirecting Number (e.g. the device diverting to the

Hi Just moved offices in the UK and moved our Asterisk box from old one to new one. Using idefisk softphones, Junghanns quadbri card for ISDN 2e interfaces. At both offices we had one standard number and a DDI range, routed with Asterisk. We'd set up the configuration so each idefisk set its own caller ID which then got sent by the extensions.conf script. Worked fine at old place but in

Hello all, I was wondering if anybody knows where one might obtain a PCI ISDN card supporting a single BRI for use with Asterisk in Australia (and using something like chan_capi). Because of the Isdn4Linux DTMF issue, I don't want one of those cards. I've already spent too much time messing about with my current card. I'm after something like the AVM Fritz! cards. I found one place

Dear All, While wanting to create a package using the name DDI (which stands for Data Documentation Initiative), I sent an email to the DDI Alliance and ask if they would mind, knowing they are now in the process of copyrighting this brand. The answer I got was negative (due to possible infringements on copyright issues), but they thanked me for raising this matter and now asking if a package