similar to: problems setting up E100P E1 germany

Hi All, I am a newbie to asterisk, and here is my first problem, where I do not know any further. I have to grandstream BT100 connected to asterisk. Working fine, for calling to each other, and to call via a IAX-Link to the outside. If I try to call the initial demo from the samples.extensions.conf I have nothing to hear. The CLI fine reports: -- Executing

Hello ml, i need some help on my zaptel configuration. My E100P only shows some YELLOW / RED alarm when I load the wct1xxp module and do a cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS YELLOW RED ... .. . My /etc/zaptel.conf is: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=nl defaultzone=nl I tried zaptel-1.0RC2 and the latest CVS

Hi. I still hace problems getting my line to work. When I start asterisk, I can see: == Parsing '/etc/asterisk/zapata.conf': Found -- Registered channel 1, PRI Signalling signalling ... -- Registered channel 31, PRI Signalling signalling == Starting D-Channel on span 1 == Registered channel type 'Zap' (Zapata Telephony

Hi, I hope someone can help me with this.... Asterisk 1.0.6 Zaptel 1.0.6 Libpri 1.0.6, 1 Digium E100P card installed Panasonic TDA200 firmware v2.0.6 E1 Card Firmware 1.0.2 System is located in Australia, so as technologies go, I believe it is twist on the euro standard for the E1 signalling. Here is the situation. The TDA E1 card is set in cross over mode and I am using a functional

Hi, I'm having trouble configuring and E1 link , I know the E1 is a PRI and the switchtype is 5ess. The problem is that everytime I try to dial I got and error saying that it was unable to open the zap channel . Devices are created in the /dev/zap directory and I can open them with a cat /dev/zap/1. I can also see the channels in /proc/zaptel/1. Thanks in advance [zaptel.conf]

Moin, Es geht um das Dovecot-Buch. Ich nehme an, da? hier mindestens einer, der sich auskennt, mitliest: Gibt es - au?er der Sprache und dem Preis - einen Unterschied zwischen der ersten (und einzigen?) deutschen Auflage von 2014 und der englischen Auflage von 2016? -- Heiko -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type:

Ich habe eine dringende Frage!!!!!!!! ch ben?tze das Rplus mit Windows 98 . Wo kann ich die Vector heap von Rgui.exe erh?hen. Bei Eigenschaften kann ich das nicht machen. Vielen Dank f?r Eure Bem?hungen Nadine Brauchli, FORNAT *************************************************************************** FORNAT Forschungsstelle f?r angewandte ?kologie und Naturschutz Asylstr. 46/48 Postfach 8708

Sehr geehrte Damen und Herren, An der Fachhochschule Winterthur wurde f??r mich im Rahmen einer Diplomarbeit (Prof. Ruckstuhl) ein R-Programm zur Auswertung von IR-Spektren (line-shape-Analyse zur quantitativen Analyse von Gasmischungen) entwickelt. Die Daten werden einer Excel-Tabelle entnommen. Bisher werden die spektroskopischen Daten ??ber den Inhalt von 64 Kan??len ??ber die

Hallo zusammen, dann will ich mal wieder ein bi?chen Schwung auf die RoR-Liste bringen: Schildert doch einfach mal eure Erfahrungen mit Tools rund um Rails, also zum Beispiel Capistrano (formerly known as Switchtower), RadRails etc. Welche Plugins setzt ihr ein, von welchen w?rdet ihr abraten? Oder folgt ihr dem Tenor "Reuse is overrated" und schreibt euch die Sachen lieber neu? --

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

hi see below's conversation. it seems the e100p card doesn't work with BT. Any idea how this'll work against Telenor (norway)? roy <RoyK> does anyone know if I can trust the E100P to do full PRI stuff in .no? <cypromis> dunno about no <cypromis> I cannot use it in UK <cypromis> cause the framer has problems with system-x switches at bt

Hello, I have a E100P card from digium and I try to implement a conference bridge in asterisk. I wonder since I got the E100P card do I still need to load ztdummy for caller from h323 endpoints to work with Meetme? I load the E100P driver but i did not load the ztdummy driver. My h323 caller does not hear any voice play by Meetme. Looks like ztdummy is required as long as h323 is concern and

hi All, quit new to asterisk, can anybody tell me whether Wildcard E400P and Wildcard E100P support R2 CAS protocol. if they do, what is the value, i should set to 'signalling' parameter in the zapata.conf file? Surajee -------------- next part -------------- An HTML attachment was scrubbed... URL:

All, I'd like to buy an E100P Wildcard frm Digium, but i prefer to buy it in Europe (costs, ...). Could somebody point me to an european reseller ? Thanks in advance. -- Nicolas Cartron nc@ncartron.org

Hello, Thanks to members of the list things changed on my installation (asterisk + digium E100P with of course an E1 line). Here is my zaptel.conf : - span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=fr defaultzone=fr - Output of zttool: - Alarms Span YEL/RED Digium Wildcard E100P E1/PRA Card 0 - [root@asterisk root]# head /proc/zaptel/1 Span 1: WCT1/0 "Digium

Hi ! I am trying to configure two E100P cards, but I am a bit confused with zapta.conf in what I am trying to achieve. The * will be connected to a pstn switch with two E1 PRI lines. The E1 lines will be used for incoming calls as well as outgoing calls. My problem now is what to put in zapta.conf, I would like to group all channels from both cards together (if that's possible). Does this

Just cross pairs 1-2 and 4-5 1 <--> 4 2 <--> 5 Never done an E1, but I think it's the same for a T1 4 wire cable. Tim Thompson Commercial Sales Engineer http://www.amatechtel.com (806) 722-2227 -----Original Message----- From: bam [mailto:bam@cqm.co.uk] Sent: Monday, December 29, 2003 9:12 AM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] E100P pinouts

Hi, i just received an E100P, this is the first one I have ever seen, and notice that the board reads T100P. Is this right ? The antistatic bag had a small label that has E100P written on it, and the card is a bit different than the T100P I already have, Does Digium use the same boards for both cards ? I don't have an E1 link here, can I test the card just by loading the driver and run

Hi, I'm installing my first E100P. My zaptel reads the following: Span=1,0,0,ccs,hdb3,crc4 E&m=1-31 My Zapata.conf reads the following: Signaling = em_w Channel =1-15 Channel =16-31 After starting the zapter service I get: ZT_SPANCONFIG failed on span 1: No such device or address (6) ??? PauloHM -------------- next part -------------- An HTML attachment was scrubbed...

I've seen this question asked before but haven't seen a definative answer. Does the e100p work in australia? Did any one who was asking the question before bite the bullet and get one? I can get a te410 if i really have to but would prefer to stay with the cheaper option. Any comments appreciated, Thanks ------------------------------------------------- This mail sent through IMP: