similar to: wcfxs error

Hi, I have received a new card TDM400P revision E, from digium. When I tried to modprobe wcfxs it gave me the following errors: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 255 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 255 should be 2 Module 1: Not installed ProSLIC on module 2 insane (1) 255 should be 2 Module 2: Not installed

I apparently have a dead FXS module. Is there any kind of test I can run on it (on a live system) to determine if its good or bad? The telephone has no dialtone, gets no calls. It has been working for several months, and just quit yesterday. Thanks! Found a Wildcard TDM: Wildcard TDM400P REV I (4 modules) Freshmaker version: 73 Freshmaker passed register test Module 0: Installed -- AUTO

The REV I card shows up in the PCI table as: 02:05.0 Network controller: Tiger Jet Network Inc. Intel 537 (or 02:05.0 Class 0280: e159:0001) Subsystem: Unknown device b119:0001 But the REV E/F shows up as: 02:0d.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface (or 02:0d.0 Class 0780: e159:0001) Subsystem: Unknown device b100:0003 One

Hi, I'm trying to get up and running a TDM400 with a standard italian pots line but i'm having problems at getting asterisk to detect when the line get answered on outgoing calls. I'm using asterisk 1.6 beta 9 with zaptel 1.4.11. I tried with and without answeronpolarityswitch=yes but it didn't change anything at all. With callprogress=yes answer get never detected. With

Hello. I have this problem. In my asterisk box, I was running debian woody with asterisk package from backports.org. Last friday I upgraded from debian to sarge and change from kernel 2.4.18-1-686 to kernel 2.6.8-1-686, rebuild zaptel kernel module and also upgrade to asterisk 1.0.2. But now asterisk won't start. Here is more info #asterisk -vvvvvvvv (last lines) [chan_zap.so] =>

Hi all, Does somebody know why no load modules to FXS? I used zaptel-1.0.7 version driver. [root@server1 zaptel-1.0.7]# modprobe wctdm ZT_CHANCONFIG failed on channel 3: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? /lib/modules/2.4.21-27.EL/misc/wcfxs.o: post-install wcfxs failed

Hello, I have few questions about Asterisk. I installed Asterisk from CVS on FreeBSD and I made cvsup 2 days ago. 1.I couldn't find Asterisk version using "asterisk -V" command. How can I to find version information? 2.I am using Wildcard X101P (FXO) and Wildcard TDM400P REV E/F (FXS)on it. I tried Asterisk CallerID feature, but unable to get it. I tried callerid signaling V23,

Hi, I got my TDM11B and am trying to get it to work on my PC. However, I'm having difficulty getting the wcfxs driver to load. I've Googled this problem, and while there are others who have ran into the same problem, none of the solutions work for me. I would very much appreciate it if you could suggest things I could try to resolve this problem. Details follow. The PC is somewhat

I'm running Asterisk on a Gentoo box with the Zaptel 1.2.1 drivers. If I boot the machine without having the wcfxs module autoload, then install the module with modprobe, asterisk works just fine. If I boot the machine and autoload the wcfxs module, the module loads fine: > Jan 11 11:06:55 asterisk Zapata Telephony Interface Registered on major 196 > Jan 11 11:06:55 asterisk ACPI: PCI

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

Hi all, I have just purchased the DevKit from Digium and received a X100P and a TDM400P (it has one FXS module). The problem is that I can't get the kernel module (wcfxs) to load and run. I have searched the archives and can't find anything about this. Do the messages below ring any bells with anyone ? There is no interrupt clash (see pci list below). I am running on a AMD 1.2G

Hello I am (attempting) to run the astlinux version of Asterisk on a VIA embedded platform. I have a TDM04B and pretty sure zaptel.conf and zapata.conf setup OK. They worked fine with same card in traditional PC anyway. I think need the module wcfxs for a Digium TDM04B card. Is this module not part of astlinux? Do I need to download it? Or is it in opt? I see wctdm - but think that is

I need to reopen this discussion because it's impossible to run spandsp (and VoIP) under these circumstances. With zaptel unloaded, I see the following "vmstat 1" output: no swapping, an occasional disk output, +/- 1003 interrupts/sec., less than 10 context switches/sec., CPU idle 100%. A very quiet system. I load modules zaptel and wcfxo, and the system utilization stays the

Hi All, I have a problem (at least I think it's a problem) where the wcfxs module causes constant CPU usage spikes. The card being used is a Digium Wildcard TDM400P with 3 FXO modules and 1 FXS (TDM31B). Monitoring my otherwise idle asterisk box (with top) I see once every 3-5 seconds hi (hardware interrupt) spike to 30%-40% and then drop back to 0 again. This is the case wtih both asterisk

I just installed an FXS module onto a 4 channel tdm thats about 5 years old and it wont work. Running dmesg I can see the following error: Zapata Telephony Interface Registered on major 196 Freshmaker version: 71 Freshmaker passed register test !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000 !!!!!!! RING_TRIP_TRES iREG 1D = 8000 should be 3600 !!!!!!! COMMON_MIN_TRES iREG 1E = 0 should

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

Hi, We have two of these 4 port FXO cards. However, we are having some problems with incoming/outgoing calls. The latest version of Asterisk/zaptel from CVS is being used. Voicemail, internal SIP <-> SIP calls between Pingtel xpressa hard phones work terrific, echotest is fine, and so on. The zaptel and wcfxs modules load fine, and show all 8 FXO interfaces in dmesg:

Hi all, I have been looking at the code for both the zaptel driver (wctdm.c/wcfxs.c) and the asterisk channel driver (chan_zap.c) trying to figure out how much of this that has been implemented. So far I can see that the current stable 1.0.9.1 zaptel driver don't have the SETPOLARITY ioctl that would be required to properly signal the Swedish/Dutch CLIP, but the 1.2 beta1 has this

Hi all, I was wondering if anyone had any pointers on how to determine whether or not a module has gone wonky on the TDM400P? I have a 2 FXO (channels 3 and 4) and 2 FXS unit (channels 1 and 2). The bad (?) module in question is the FXO module on channel 3. I can't dial in to or out of that channel; dialing in gives a busy signal, dialing out just shows * hanging around after attempting a

(I'm producing a writeup on all the things one run into building an * box. Which after a couple of boxes is showing up aplenty.) So this uses the working h/w and config's from another box. All I do is build in a new computer. Loading the modules I got: __________________________________________________ Zaptel Configuration ====================== Channel map: Channel 01: FXS