similar to: can't load x100p card

Hmm, I don't have /etc/modprobe.conf, and wctdm is giving me problems. Which device is it talking about? [root@asterix /]# modprobe wctdm /lib/modules/2.4.20-8/misc/wctdm.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg

Hi all i need urgent help our entire switchboard is down only 5 days after it came up. this is the second time this has happened and i am thinking that asterisk is not worth the trouble it gives. mostly it runs without hassle. but around 2 weeks ago during the test phase we rebooted the machine and did the normal modprobes and this error popped up. coming back to work after the weekend the

Hi All, Googling X100P Clone I found several information about these cards and seems that some winmodem has the same chip used from the original X100P. Here below a list winmodem which should work as X100P clone: 1057 Motorola 5608 SM56 PCI Fax Voice Modem E159 Tiger Jet Network Inc 0001 Tiger 300/320 PCI interface I bought one "Trust 56k V92 PCI Internal Modem MD-1100" which has the

Thanks in advance root@asterisk01:~# modprobe wcfxo /lib/modules/2.4.20/misc/wcfxo.o: init_module: No such device /lib/modules/2.4.20/misc/wcfxo.o: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.20/misc/wcfxo.o: insmod /lib/modules/2.4.20/misc/wcfxo.o

I have * working on my Sony Vaio PCG-FX120 laptop. I am trying to get * to recognize my internal PCI Intel modem as an FXO port. I have modified wcfxo.c in order to identify the PCI modem properly. Based on output from dmesg, wcfxo didn't recognize the modem until I inserted the proper vendor and device IDs into wcfxo.c and re-compiled. Note that the error message from "modprobe

I am starting to dip my toes into the asterisk world, and to that end I've scavenged an old PC (this is a home project, and I have basically $0 to spend on it), and installed FC1. I've purchased a clone X100P (or at least I was told it was), and I am trying to get it to work. However, when I try and load the wcfxo module, I get the following errors... [root@loudhoward root]# insmod

Hi All I've bought a TDM400P and need some help with configuration. Can you tell me what to do ? I've tried to install and the message below has appeared: [root@voip asterisk]# modprobe zaptel [root@voip asterisk]# modprobe wcfxo /lib/modules/2.4.22-1.2115.nptl/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid

Hi All, I have the problem setting up TDM22B card. Steps what I have followed are: [1] compiled zaptel-1.0.9.2 & installed the same. [2] modprobe wcfxo /lib/modules/2.4.20-8/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg

Hello everyone. I hope that this isn't a sore topic, but I've spent a week now reading through everything I could dig up from the archives on this topic, and I'm not yet satisfied with any conclusions presented there. I've also spent a few days hacking on the Asterisk code, trying to understand how things work better, and I'm still not ready to give up. I well-realize

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

I have Wildcard TDM400P - so after compile i'm loading zapatel and wcfxs - kernel modules. My question is does I need other module in order to work with the FXO and FXS. ( beacause in other document i've noticed that there was writen to load and wcfxo - module ) but when i try this I get an error. voipgw:~# modprobe wcfxo /lib/modules/2.4.26/misc/wcfxo.o: init_module: No such

Hi! I have just bought the X100P and TDM400P cards to install on my computer to implement the PBX. I also downloaded the newest softwares asterisk_ver0.5.0, libpri_ver0.4.0, and zaptel_ver0.7.0) to install on my computer (Red Hat Linux 8.0). All packages are compiled well. When I use "modprobe" to load drivers (modprobe zaptel, modprobe wcfxo, modprobe wcfxs), the first two (zaptel,

Hi, I'm trying to figure out why my Sweex CA000022 is not detected by wcfxo on my SuSE Pro 9.3 running on a VIA EPIA SP motherboard. The card should work as its an Intel 82537EP based card. When Booting the IRQ assignments for the board indicate: Bus Dev Func Vendor Dev Class 0 20 0 8086 1080 0703 lspci shows: 0000:00:14.0 Modem: Intel Corporation: Unknown device 1080

I have two X100P cards that were working just fine for months. When I run modprobe wcfxo today I got the following error: ZT_CHANCONFIG failed on channel 2: No such device or address (6) /lib/modules/2.4.19/misc/wcfxo.o: post-install wcfxo failed /lib/modules/2.4.19/misc/wcfxo.o: insmod wcfxo failed The output of dmesg said that wcfxo:Out of space to write register 06 with e0. What?s

Hi, I've seen some reports about ruuning Intel modem with 537 or MD3200 chipset running with Zaptel drivers as a FXO port. Did anybody managed to set up a PCI faxmodem based on Intel536ep chipset to work with * and Zaptel drivers? Modem seemd to work just fine with Linux, but the driver says no;) some more info: Linux 2.4.26 mazuchna:~# cat /proc/pci | grep 536 Communication

Hello Everyone, I just got my Dev Kit TDM today... :D I installed the X100P ok (wcfxo); however, when I tried to 'modprobe wcfxs' for the TDM400P(TDM10B), I got this error message: /lib/modules/2.4.19/misc/wcfxs.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters /lib/modules/2.4.19/misc/wcfxs.o:

I have put a box together using 2 X100P and 2 TDM400 4port cards. Using the simple setup that Martin posted a few days ago, I have asterisk almost up and running. /etc/zaptel.conf fxsks=1-2 fxoks=3-10 loadzone=nz defaultzone=nz (I have added NZ tone information to zaptel and Asterisk - I'll submit a patch soon). /etc/asterisk/zapata.conf [channels] context=incoming signalling=fxs_ks

Hi, I got my TDM11B and am trying to get it to work on my PC. However, I'm having difficulty getting the wcfxs driver to load. I've Googled this problem, and while there are others who have ran into the same problem, none of the solutions work for me. I would very much appreciate it if you could suggest things I could try to resolve this problem. Details follow. The PC is somewhat

This is a system for our lab. I have no problem getting rid of X100P clones. But I am just curious why can they work. Even the drivers are not loading correctly. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Kerry Garrison Sent: Tuesday, May 02, 2006 10:51 AM To: 'Asterisk Users Mailing List -

Hey all, ? I'm trying to get an E400P and 2 X100Ps working together in the one box and don't seem to be having much luck. ? I can get the two different types of boards working separately, but not together.? I've made calls on both the X100P and have seen sync and correct signalling on the E400P.? But when I try to enable to configs together I get the following: ? modprobe wcfxo