similar to: Help installing FXS card

(I'm producing a writeup on all the things one run into building an * box. Which after a couple of boxes is showing up aplenty.) So this uses the working h/w and config's from another box. All I do is build in a new computer. Loading the modules I got: __________________________________________________ Zaptel Configuration ====================== Channel map: Channel 01: FXS

The REV I card shows up in the PCI table as: 02:05.0 Network controller: Tiger Jet Network Inc. Intel 537 (or 02:05.0 Class 0280: e159:0001) Subsystem: Unknown device b119:0001 But the REV E/F shows up as: 02:0d.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface (or 02:0d.0 Class 0780: e159:0001) Subsystem: Unknown device b100:0003 One

Is there anything special needed to load up a TDM10B card?? I got the card today.. Took it from the box, put it into a PCI slot.. connected the power to the card and booted the PC.. I have removed the X100P to avoid confusion and I have the following in the config files.. in /etc/zaptel.conf # For the X100P #fxsks=1 # For the TDM10B fxoks=1 in /etc/asterisk/zapata.conf [channels]

Hi, I got my TDM11B and am trying to get it to work on my PC. However, I'm having difficulty getting the wcfxs driver to load. I've Googled this problem, and while there are others who have ran into the same problem, none of the solutions work for me. I would very much appreciate it if you could suggest things I could try to resolve this problem. Details follow. The PC is somewhat

Thanks in advance root@asterisk01:~# modprobe wcfxo /lib/modules/2.4.20/misc/wcfxo.o: init_module: No such device /lib/modules/2.4.20/misc/wcfxo.o: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.20/misc/wcfxo.o: insmod /lib/modules/2.4.20/misc/wcfxo.o

hi guys, i got a TDM400P FXS card an everything is fine except for this when i do modprobe wcfxs , the linux shows 2 TigerJet Network Inc Model 300 128k. i don't know why it is showing 2 of them. or is that what it is? ERROR: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 0 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 0 cshould be

I've been having trouble with a TDM10B that I installed a few days ago. At first I could not modprobe it at all (getting the errors below). I switched the X100P that was also installed (with a Motorola chip) with one with a Tiger-something chip, and then everything starts up okay. However, after a few hours, the FXS port dies (no battery or anything), and if I try to rmmod & modprobe

I have a E110P which I can't seem to make function and i think it has something to do with interrupts, but I've never had to deal with them before and was wondering if someone could offer some guidance. a modprope zaptel loads fine. when i then do modprobe wcte11xp i get the following: /lib/modules/2.4.21-27.0.1.EL/misc/wcte11xp.o: init_module: No such device Hint: insmod errors can be

Hi, I'm trying to configure a clone of X100 for use with asterisk, but i have reached the zaptel.conf step and have not been able to progress further as i'm getting the following error: arnor:~# ztcfg -v Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: Invalid

Hi! I have just bought the X100P and TDM400P cards to install on my computer to implement the PBX. I also downloaded the newest softwares asterisk_ver0.5.0, libpri_ver0.4.0, and zaptel_ver0.7.0) to install on my computer (Red Hat Linux 8.0). All packages are compiled well. When I use "modprobe" to load drivers (modprobe zaptel, modprobe wcfxo, modprobe wcfxs), the first two (zaptel,

Hello Since TDM cards are known for being particular when it comes to motherboards (PCI 2.2, etc.), I was wondering if there is a utility that can check that the Zaptel driver works OK and can tell if the TDM card is compatible? That way, if an FXO module is not reporting an incoming call, we'd know it's because of the Zaptel driver, and not something elsewhere. Are "dmesg",

I just needed to test a dialup modem connection (don't ask) and I had a modem connected to a TDM card (FXS port) which then dialled out via a E1 PRI on a TE4xxp card. See my log below: atdt0198xxxxxx CONNECT 36000 V42bis ** Dial IP ** Username: xxxx Password: Entering PPP Session. IP address is xxx.xxx.xxx.xxx MTU is 1500. OK ATH0 OK ATDT0198xxxxxx CONNECT 31200 V42bis ** Dial

hi there I'm trying to get asterisk going on gentoo 2005.1 I'm just getting my feet wet so I thought I would just stick with the stable portage packages. Right now that's asterisk 1.0.8 I emerge asterisk with the following make.conf file: CFLAGS="-O2 -mcpu=i686" CHOST="i386-pc-linux-gnu" CXXFLAGS="${CFLAGS}" USE="-gtk -gnome -qt -kde -dvd alsa

Hi, I have installed a TDM400P in a PC which runs RedHat Linux 3.2.2-5. There is an FXS module connected to the first slot of TDM400P and an FXO module connected to the fourth slot. This card is detected by the operationg system, which I was able to make sure using the output of lspci command. I modified the configuration files zaptel.conf, zapata.conf and extensions.conf. When I execute the

I was studying the asterisk-users list archives to learn if anyone has had success with an X100P on a sparc. I noticed some postings on the subject. I am wondering if anyone has learned anything new? I have an Ultra-60 running Gentoo with 2.6.10 and udev. I built * 1.0.5 and have been enjoying various SIP configurations, with 2 sipura phones and 2 UIP200 phones (got them working!) in my home,

I have a TDM400P with one FXO module and two FXS modules in it. I also have a Wildcard X101P. After trying hard to get things working on various Intel computers, but having echo problems that made it not really usable, I decided to try it on some older PowerPC (Macintosh) hardware running Yellow Dog Linux. Things started off smoothly. Both zaptel and asterisk seemed to compile okay, and both

Hi everybody, I managed to install card over Suse 9.2, I substituted Zaptel drivers and compiled them. Now "ztcfg" says I have one card with correctly configured 31 channels, but red led on back of card doesn't flash. Suse 9.2 has detected the card as a Tiger Jet card, since the chip on it is a Tiger 320. The second card configuration is still waiting for configuration, but I think

It's a udev configuration. Read UDEV.txt, or, read the AMP wiki http://aussievoip.com for a step-by-step. --Rob -----Original Message----- From: asterisk-users-bounces@lists.digium.com on behalf of Jachin Rupe Sent: Wed 7/09/2005 9:16 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] /dev/zap* is not showing up (gentoo, portage,asterisk 1.0.8 hi

Hi all, I am trying to add a TigerJet usb adapter to my asterisk installation I have the 1.2.4 asterisk bristuffed version, holding two zaphfc (ISDN) cards If I connect the TigerJet adapter to my linux box (Suse 10) i see: Bus 005 Device 001: ID 0000:0000 Bus 004 Device 003: ID 06e6:831c Tiger Jet Network, Inc. Bus 004 Device 001: ID 0000:0000 Bus 003 Device 001: ID 0000:0000 Bus 002 Device

Hi all, Does somebody know why no load modules to FXS? I used zaptel-1.0.7 version driver. [root@server1 zaptel-1.0.7]# modprobe wctdm ZT_CHANCONFIG failed on channel 3: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? /lib/modules/2.4.21-27.EL/misc/wcfxs.o: post-install wcfxs failed