similar to: Digium FAQ.

I'm attempting to configure a machine with a DevKit Lite (X100P & S100U). After I modprobe wcfxo, the machine goes into some kind of loop after about 10 seconds, where it spits out what appears to be 32-bit addresses, ad infinitum. At this point, the machine becomes completely unresponsive to keyboard input (i.e. Ctrl-C, Ctrl-Alt-Del, even CapsLock and NumLock states [lights] cannot be

Hello all. I am trying to get my second x100p card set up and am having some troubles. My zaptel.conf reads: fxsks=1-2 fxoks=3-4 defaultzone=us loadzone=us before adding this card my zaptel.conf read: fxsks=1 fxoks=2-3 defaultzone=us loadzone=us But now that I've made the change I am getting the following error when running modprobe wcfxo and of course the same

Hi all, I am trying to add a TigerJet usb adapter to my asterisk installation I have the 1.2.4 asterisk bristuffed version, holding two zaphfc (ISDN) cards If I connect the TigerJet adapter to my linux box (Suse 10) i see: Bus 005 Device 001: ID 0000:0000 Bus 004 Device 003: ID 06e6:831c Tiger Jet Network, Inc. Bus 004 Device 001: ID 0000:0000 Bus 003 Device 001: ID 0000:0000 Bus 002 Device

Installing DevkitLite hardware (Very similar to John Lange's post on Tue Oct 08 2002) I cannot get anything to work on the phone connected to the s100u. I dont know what to do. Can someone please help me? I used the sample configuration files from digium documentaion that was supposed to be "sane" defaults for the kit. Very similar to John Lange's post on Tue Oct 08 2002 Here

I am having a problem with Red Alarms on X100P cards. The most frustrating thing is I can not duplicate the alarms, therefore am not sure how to solve it. I have read after searching posts and the web that you can try different signaling methods which may help alleviate the problem. There is fxsks (Which I am currently using), fxsgs, and fxsls While reading the Digium site about these different

I am trying to find an example of how to set up my FXS Station Card in my Asterisk. I have (1) XP100P I have (1) tdm20B (2 Port FXS) Could someone tell me if this is correct? /etc/zaptel.conf fxsks=1 fxoks=2 fxoks=3 loadzone=us defaultzone=us /etc/asterisk/zapata.conf [channels] ; language=en ; ;X100P Port 1 context=inbound-analog signalling=fxs_ks usecallerid=yes echocancel=yes

I have two grandstream budtetone-100 and cisco 7960g phones. When I talk via speaker phone on either of the phones I get a lot of echo. Any suggestions? Also how do I turn on the mark echo canceller. -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of asterisk-users-request@lists.digium.com Sent: Tuesday, April 13,

Hi, I just got my TDM400P card (2 modules) and i installed it no probs. The card is detected fine, but for some reason when I add the card to zaptel.conf i get the following error: --snip-- ZT_CHANCONFIG failed on channel 2: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? --snip-- My /etc/zaptel.conf looks

Hello. I am a spanish student, so excuse my English. I have this HW: - 2 X100P PCI with two analog lines plugged in. These lines are two extensions of a panasonic PBX. Zap/1 = X100P <-- analog line --> extension #237 PBX Panasonic Zap/2 = X100P <-- analog line --> extension #245 PBX Panasonic - 1 TDM20B with two analog telephones plugged in. Zap/3 = TDM20B

My setup: X100P and Quicknet PhoneJack. I can't seem to properly set up a Zap channel for my X100P. Here are some of my configurations: [zaptel.conf] fxsks=1 #X100P fxoks=2 #Quicknet PhoneJack defaultzone=us loadzone=us [zapata.conf] [channels] context=local signalling=fxs_ks channel->1 ;X100P [extensions.conf] ... [local] exten=>_NXXNXXXXXX,1,Dial,Zap/1 ;I'm pretty sure the

Hi, Would someone assist me with the configuration of my TMD10B and X100P cards? I would ask Digium but my support was good for only one install...( I had to rebuild my * box). I wrote down the configuration but I must have made a mistake somewhere. I have followed the instructions on the Digium site but I must be missing something. Here's the config (snippets) I've been attempting to

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

no matter which way I have my /etc/zaptel.cfg this only started happening after a yesterdays CVS update to my zaptel source... Line 1: fxoks=1 Line 2: fxsks=2 Line 23: loadzone=us Line 28: defaultzone=us <End of File> Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) 2 channels

Hello, my first post to the list. I have started to install and play with Asterisk. I was following some basic instructions to 'jump-start' my system. I have a TDM400P with one port and a X100P. I am running the latest CVS versions (from today). Following the steps I found for basic jump-start I did the following: Modprobe zaptel Modprobe wcfxo Modprobe wcfxs Edited

I'm having a problem getting 3 way calling to work correctly using two outside lines and one extension. The two outside lines are connected to the X100P's and a standard model 2500 phone is connected to the TDM10. When I dial the first outside destination 9xxxxxxx, the call completes correctly. When I flash the hook switch and dial the second location 9yyyyyyy. The call doesn't

Hi list. I'm having the next problem. I have a * with 1 TDM400P (4 ports) and one X100P, with a working configuration. Today i add one more X100P card, and i change the config files as next: zapatel.conf: fxsks=1-2 fxoks=3-6 loadzone = us defaultzone=us zapata.conf ... context=bell

Hi, I have configured tdm400p alone and it works fine for me. But now i tried to add 2 x100p in the same machine with the following configs, but asterisk refuses to load, can someone guide me what i have done wrong. Following r the configs and output. TIA, Azher >> ./asterisk -vvvvvc [chan_zap.so] => (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found --

Specs: Fedora Core 3. Dual P3 600 (Dell PEdge 1300) SCSI Disks 1x X100P (channel 1) 1x TDM20 (channels 2+3) 1x Knockoff X100P (channel 4) I am looking to have all local and all toll free calls go outbound through the Copper line, and all long-distance and international to go out through the Vonage line. This way I can eliminate LD on my home line, and pay minimal LD charges through

I have decided to move on from Asterisk@Home and start compiling asterisk myself now. I got a dedicated box and put my X100P in it. I installed the server version of CentOS 4.2 (2.6.9-22.EL kernel) barebones. The box is a dell GX270 workstation with 1GB of RAM. I got a fresh copy of O'Reilly's Asterisk the future of technology and begun. I downloaded the zaptel-1.2.4.tar.gz, libpri-1.0.9,

When I try to start up zaptel, whilst running ztcfg, I get the following error: Jan 1 10:48:18 bu ztcfg: ZT_CHANCONFIG failed on channel 2: No such device or address (6) My /etc/zaptel.conf is: fxsks=1 fxoks=2 loadzone = au defaultzone=au Channel 1 is a X101P card connected to the PSTN and channel 2 is a S100U box driving an analogue phone. The zaptel kernel module gets loaded OK as does the