similar to: Identify call router? How?

Displaying 20 results from an estimated 6000 matches similar to: "Identify call router? How?"

2005 Apr 22
4
TE11OP -> Mitel 200Sx??
Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows. Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card. All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card. Any advice would be great. Zaptel.conf span=1,0,1,d4,ami e&m=1-23 dchan=24
2004 Aug 22
3
asterisk T100P to Merlin Legend
Management just approved purchase of a Digium T100P and a T1 card for our Merlin Legend Switch. I will appreciate comments from anyone performing this installation before: - Which T1 card did you use in the Merlin Legend? - Did you require any special interface? (CSU/DSU, etc) - Any items to watch during installation. Also we will need to remove one of our old analog Trunk cards to accomodate
2010 May 16
4
ISDN config: LBO values
Hi all, When configuring Asterisk with an ISDN card, it will at one point become necessary to select the LBO (Line Build-Out) value. This is an integer (0-7) that is determined by the length of the cable and is selected from the following table. Many of us are familiar with it: CSU (dB) DSX-1 (feet) ------------------------------- 0 0 0?133 1
2002 Sep 04
1
Anybody Configure Shorewall w/ Sangoma WANPipe T1?
Hi, I learned about shorewall a few days ago and am quite impressed with how easy it was to create a powerful firewall. I set up a test system with a cable modem and it worked flawlessly. I''m going to be building a Router/Firewall for a new T1 that will be using a Sangoma WANpipe card w/ integrated CSU/DSU to connect to a T1. Has anybody done this yet, or do you know if it''s
2007 Jan 12
3
Linux as T1 router
Hello All, I am thinking about using a linux server as a T1 router. I have searched the list, but have not found a discussion about what I''m trying to do. I have a situation where the Cisco router I''m using will not handle the additional bandwidth I added recently. Unfortunately, I cannot afford the Cisco unit that will. I would like to know if anyone has successfully done
2004 Jul 09
7
Predictive Dialers
Hi, I was just wondering if anyone knows how predictive dialers detect voicemail and answering machines, and if they could explain to me how that works. Thanks! Brian.
2006 Apr 07
1
suggestions on an IP T1 to TDM T1 gateway solution
Can anyone offer up a suggestion on a reliable and cost effective customer premise hardware setup to be able to take an inbound IP T1 and deliver a PRI interface to a remote office? Trying to reduce the amount of hardware required to implement this, right now we use a Cisco router to take the IP T1 in on a serial port and then we go Ethernet to a slimmed asterisk box with a single port T1
2004 Nov 22
10
routed vs non routed
In an effert move my Dmz from a snapqear roouter to Linux with shorewall. Question is I have network 64.42.53.200/29 which makes default gw 64.42.53.201 network 64.42.53.200 broadcast 64.42.53.207 mask 255.255.255.248 and I want to set up shorewall with eth0 64.42.53.202 eth1 local eth2 dmz where dmz will use say 64.42.53.203 for web and email server. Where I do not need or should I say use
2004 Dec 17
2
OT: "Integrated Access T1" voice problems - is this possible?
Hello, I am currently pricing out various T1 and PRI options for a client of mine. We need voice and data - we want T's. Whether it be two seperate T's, two superate fractional T's, or one combined fractional T, we need it done. We are getting pricing and one provider is telling us that they have quality issues with the "Integrated Access" product. From what they
2004 Mar 10
11
Predictive Dialer
hi we need a predictive dialer which can be used with asterisk software. Is it possible? Bye Owais Bin Zuber --------------------------------- Do you Yahoo!? Yahoo! Search - Find what you’re looking for faster. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040310/a49a4b5c/attachment.htm
2004 Jul 10
5
Three (quick?) questions...
[Please excuse if this is a repeat; I initially tried to send it from a different account, and it's been held up for a couple of days awaiting moderation.] 1) What's the absolute minimum required (hardware-wise) in order to get one in-bound POTS line into Asterisk, and then have IP phones "inside?" [In other words, I obviously need a NIC -- but what would be the
2007 Jun 11
1
Slightly OT:CSU on Digium cards, and it's requirement
Do the Digium cards have a built in CSU? Is a CSU an FCC requirement? or just a carrier requirement? TIA
2006 Feb 01
1
RE: Asterisk-Users Digest, Vol 19, Issue 10
Need help...I need to install a card to terminate 7 lines...I have not order the phone lines yet...I can either do analog lines 1FBs or order a fractional T1...any suggestions on what hardware would be easier to install and configure...also if I went with a T1...do I need an external CSU/DSU or anything or does it just plug into the T1 card...thanks.. -----Original Message----- From:
2007 Apr 11
1
Purposely setting red alarm on PRI for testing purposes
Does anyone know if is possible to purposely set red alarm status on PRI circuit for testing purposes (other than unplugging it). I have looked for a console command which might allow this.... -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070411/985e8e64/attachment.htm
2004 Aug 16
1
Set-up for 2 Asterisk System
Hello, I will be setting up two asterisk systems and I'm looking for some suggestions as to what the best way to do this will be. The 2 systems are for 2 companies that share a single T1 line. The T1 line has 12 voice channels and 12 data channels. Currently, they are set-up as follows: T1 line from provider enters CSU/DSU and splits voice/data channels. The voice channels are sent to
2018 Jul 25
3
How to know the IP of "manager show connected" in dialplan
​I need to launch a remote process at the machine that has the dialer. I could hard-code the IP address in a global variable, but It would be much more elegant if the dialplan would have a "manager" object where I could read "manager-->connected". ​ -------------- next part -------------- An HTML attachment was scrubbed... URL:
2007 Oct 08
1
Sine Dialer, GNU dialer, VICIDial and others slightly OT?
Hello All, I have a requirement to setup a predictive dialer for a customers call center. I am asking for pros and cons of the different dialers available for Asterisk. If you are going to send marketing material send it to my e-mail directly please and not to the list. I was hoping to get the opinions of any one using any of these dialers and what they liked and didn't like, ease of
2014 Feb 14
2
Dialer software for Asterisk...
I have a customer with a more or less unique need. Right now we are using Wombat as a dialer software so they can contact clients for QA purposes. Everything is working very well and their contact center productivity is way up from the old manual dialing method. The only thing we are having a problem with is that they have up to 5 phone numbers to contact a single customer. Obviously
2011 Jun 21
4
call paging interrupts call when using Mitel 5224
Is anybody using Mitel phones? It appears that when you page a Mitel phone using asterisk's MeetMe, the paged phone will hang up the call its on to take the page. Thanks in advance. -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20110621/764a6fa9/attachment.htm>
2008 Mar 04
4
Mitel SX-200 + *
Does anyone have any experience getting a Mitel SX-200 EL/ML PBX system to work with *? I'm not getting inbound or outbound calls to work. (Inbound caller gets line busy tone.) SETTINGS FROM MITEL: I built a Crossover cable and connected it like this: PSTN--T1--ASTRISK--T1--OLD MITEL -Crossover Cable Pin-out: 1 - 4 2 - 5