similar to: TDM400p loading errors

hi guys, i got a TDM400P FXS card an everything is fine except for this when i do modprobe wcfxs , the linux shows 2 TigerJet Network Inc Model 300 128k. i don't know why it is showing 2 of them. or is that what it is? ERROR: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 0 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 0 cshould be

The REV I card shows up in the PCI table as: 02:05.0 Network controller: Tiger Jet Network Inc. Intel 537 (or 02:05.0 Class 0280: e159:0001) Subsystem: Unknown device b119:0001 But the REV E/F shows up as: 02:0d.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface (or 02:0d.0 Class 0780: e159:0001) Subsystem: Unknown device b100:0003 One

I apparently have a dead FXS module. Is there any kind of test I can run on it (on a live system) to determine if its good or bad? The telephone has no dialtone, gets no calls. It has been working for several months, and just quit yesterday. Thanks! Found a Wildcard TDM: Wildcard TDM400P REV I (4 modules) Freshmaker version: 73 Freshmaker passed register test Module 0: Installed -- AUTO

Hi, I'm trying to get up and running a TDM400 with a standard italian pots line but i'm having problems at getting asterisk to detect when the line get answered on outgoing calls. I'm using asterisk 1.6 beta 9 with zaptel 1.4.11. I tried with and without answeronpolarityswitch=yes but it didn't change anything at all. With callprogress=yes answer get never detected. With

Hello. I have this problem. In my asterisk box, I was running debian woody with asterisk package from backports.org. Last friday I upgraded from debian to sarge and change from kernel 2.4.18-1-686 to kernel 2.6.8-1-686, rebuild zaptel kernel module and also upgrade to asterisk 1.0.2. But now asterisk won't start. Here is more info #asterisk -vvvvvvvv (last lines) [chan_zap.so] =>

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

Hi all, I have just purchased the DevKit from Digium and received a X100P and a TDM400P (it has one FXS module). The problem is that I can't get the kernel module (wcfxs) to load and run. I have searched the archives and can't find anything about this. Do the messages below ring any bells with anyone ? There is no interrupt clash (see pci list below). I am running on a AMD 1.2G

Hi, We have two of these 4 port FXO cards. However, we are having some problems with incoming/outgoing calls. The latest version of Asterisk/zaptel from CVS is being used. Voicemail, internal SIP <-> SIP calls between Pingtel xpressa hard phones work terrific, echotest is fine, and so on. The zaptel and wcfxs modules load fine, and show all 8 FXO interfaces in dmesg:

Hi all, Does somebody know why no load modules to FXS? I used zaptel-1.0.7 version driver. [root@server1 zaptel-1.0.7]# modprobe wctdm ZT_CHANCONFIG failed on channel 3: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? /lib/modules/2.4.21-27.EL/misc/wcfxs.o: post-install wcfxs failed

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

Hi all, I was wondering if anyone had any pointers on how to determine whether or not a module has gone wonky on the TDM400P? I have a 2 FXO (channels 3 and 4) and 2 FXS unit (channels 1 and 2). The bad (?) module in question is the FXO module on channel 3. I can't dial in to or out of that channel; dialing in gives a busy signal, dialing out just shows * hanging around after attempting a

Hello, I have few questions about Asterisk. I installed Asterisk from CVS on FreeBSD and I made cvsup 2 days ago. 1.I couldn't find Asterisk version using "asterisk -V" command. How can I to find version information? 2.I am using Wildcard X101P (FXO) and Wildcard TDM400P REV E/F (FXS)on it. I tried Asterisk CallerID feature, but unable to get it. I tried callerid signaling V23,

I'm running Asterisk on a Gentoo box with the Zaptel 1.2.1 drivers. If I boot the machine without having the wcfxs module autoload, then install the module with modprobe, asterisk works just fine. If I boot the machine and autoload the wcfxs module, the module loads fine: > Jan 11 11:06:55 asterisk Zapata Telephony Interface Registered on major 196 > Jan 11 11:06:55 asterisk ACPI: PCI

Greetings all, I'm new to asterisk... Finally got two IP phones and two TDM400P's (one with four FXO modules and one with four FXS modules)... Began experimenting a couple days ago and have ran into a very aggrevating problem. My system consists of the following hardware: Abit BL7-RAID motherboard Pentium 4 1.6GHz processor 512MB SDRAM 2 TDM400P cards 2 3Com 3c905

I just installed an FXS module onto a 4 channel tdm thats about 5 years old and it wont work. Running dmesg I can see the following error: Zapata Telephony Interface Registered on major 196 Freshmaker version: 71 Freshmaker passed register test !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000 !!!!!!! RING_TRIP_TRES iREG 1D = 8000 should be 3600 !!!!!!! COMMON_MIN_TRES iREG 1E = 0 should

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031223/62cf404e/attachment.htm -------------- next part -------------- Hello When I tried loading TDM400P module using insmod command, I get following error messages. Is there some problem with my asterisk installation. Please advise. Thanks Tony $insmod wcfxs Using

Hi! I have just bought the X100P and TDM400P cards to install on my computer to implement the PBX. I also downloaded the newest softwares asterisk_ver0.5.0, libpri_ver0.4.0, and zaptel_ver0.7.0) to install on my computer (Red Hat Linux 8.0). All packages are compiled well. When I use "modprobe" to load drivers (modprobe zaptel, modprobe wcfxo, modprobe wcfxs), the first two (zaptel,

I'm afraid that I am at a loss here. I am new to Asterisk, and have successfully set up SIP. But I cannot get my FXS card working, and I'm not sure what else I can try. # modprobe wcfxo /lib/modules/2.4.21-37.0.1.ELsmp/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may

Hi all, I have been looking at the code for both the zaptel driver (wctdm.c/wcfxs.c) and the asterisk channel driver (chan_zap.c) trying to figure out how much of this that has been implemented. So far I can see that the current stable 1.0.9.1 zaptel driver don't have the SETPOLARITY ioctl that would be required to properly signal the Swedish/Dutch CLIP, but the 1.2 beta1 has this

(I'm producing a writeup on all the things one run into building an * box. Which after a couple of boxes is showing up aplenty.) So this uses the working h/w and config's from another box. All I do is build in a new computer. Loading the modules I got: __________________________________________________ Zaptel Configuration ====================== Channel map: Channel 01: FXS