similar to: debugging callerid help

I have a couple of X100P's in my system and while on calls they just randomly hang up for no reason. I have tried messing with the busydetect and callprogress setting them to yes and no same and still random hangups. Is there another setting I should be looking at? My zap config looks like. context = inbound-work include => extensions signalling

supervision. Verify if for those "numbers" the CO revert the line polarity when callee answer. callprogress=no is a good test too. Jorge Ra??l G??mez C. wrote: > Hi list, > > I'm having problems transferring certain calls made by the attendant > between the PSTN and to an internal extension. Although, transfers > between the majority of the calls ends successfully.

When I enable callprogress I get this error message... (when I call, it will ring forever but asterisk is acting as if it DID pick up the line ... but it never did... ) I'm beginning to think that asterisk can't hangup the line when in voice mail and this, whatever action I'll take... Actually, callprogress doesn't seem to work at all... (in my case) Mar 24 23:37:28

Hello all! I have tried and tried to resolve this one to no avail. Hopefully one of you can help... The system in question is a Compaq Evo D600 (iirc) business desktop, with a 1.4GHz Pentium 4 and 512mb of RAM, running a stock install of PoundKey 1.2. It has two Digium cards installed: a TDM400P with four FXO modules, and a TE110P hooked to a Carrier Access Adit 600 which serves 8

Hi list, I'm wondering if it's possible to transfer a call that is still ringing??? Actually, the problem is that my telco provider doesn't offer an uniform method for answer/disconnection supervision, and by that I mean, some of it's line (I think) offer a polarity reversal, but other lines (of the same service provider) do not offer anything at all, so the answer of a call

I'm trying to set up asterisk so any phone connected to channel 1-16 of my Adit600 channel bank can pick up a call coming in on channel 24. I do not wish to ring any of the 16 channels on an incoming call -- this is strictly so I can pick up the line if I see it ringing and wish to answer at work. I have channel 24 in call group 3, and channels 1-16 in pickup groups 1 and 3. However

I'm running * on two pstn lines (x100p cards) that happen to also have analog phones installed on the incoming pair for backup (until testing is complete). If someone is talking on a pstn analog phone and they talk loud enough, * senses the voice (apparently assuming the line is ringing), and rings an appropriate SIP phone (7960). Is there a way to config * so as to only process inbound

Guys, this is weird.. Today I started having some problems with calls been dropped. Im suing X100p cards (clones) and I have this setting on my zatala fle: [channels] language=sp signalling=fxs_ks usecallerid=yes cidsignalling=bell cidstart=ring hidecallerid=no callwaiting=yes usecallingpres=yes ;sendcalleridafter=1 callwaitingcallerid=yes threewaycalling=yes transfer=yes canpark=yes

Hi list, I'm having problems transferring certain calls made by the attendant between the PSTN and to an internal extension. Although, transfers between the majority of the calls ends successfully. Debugin this, I've found that calls made to certain "numbers" (Telephony Providers), aren't detected as ANSWERED in the CDR, so they are not properly accounted (for billing),

Hi all, using * 1.2.9.1 and this week all of the sudden calls keep ringing even after they've been picked up... Here's one users summary: When I pick up the phone, I hear a dial tone and I am able to dial out. But for some odd reason, the receiving line picks up while the outgoing line is still ringing. And the receiving line can hear everything while the phone is still ringing. I tested

Hi, can't get X100P (fully zapata compatible clone) to work (I'm in Australia). * recognises the card and the channel (1) but has definetely some problems talking to the pots line. I set up this simple dialplan for ZAP ("incoming" context, as setup in zapata.conf, for channel 1) [incoming] exten => s,1,Answer exten => s,2,Playback(somefile) exten =>

Is there anything special needed to load up a TDM10B card?? I got the card today.. Took it from the box, put it into a PCI slot.. connected the power to the card and booted the PC.. I have removed the X100P to avoid confusion and I have the following in the config files.. in /etc/zaptel.conf # For the X100P #fxsks=1 # For the TDM10B fxoks=1 in /etc/asterisk/zapata.conf [channels]

Dear All, I am a newbie about asterisk. I have 1x X100P card 3x Sip phone I got aware of problem, after I saw the caller id on my sip phone. I noticed that if I receive a call from GSM Operator A, I can see caller id. But any other operator, I got no caller id, even my direct PSTN service operator. So at that moment I was using *1.0.9. than I changed to asterisk@home 1.3(1.0.9). I got same

Hi, Im getting mad with this error, I have a x100p installed with wcfxo module loaded perfectly, I can receive incoming calls and detect very good the hangup for incoming calls. But for outgoing calls its a mess. When I place a call for outgoing, i heard the ringing, my cell or phone rings and when I pick up the phone it hangs: -- Called g1/91xxxxxxx -- Hungup

I have an eight channel fxo setup (2 TDM400P cards) and I have them setup. Here are my configs: Zaptel.conf: fxsks=1-8 loadzone=us defaultzone=us Zapata.conf: [trunkgroups] [channels] musiconhold=default rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=yes hidecallerid=no callerid=xxxxxx callwaiting=yes busydetect=no callprogress=no usecallingpres=yes callwaitingcallerid=yes

Hello, I have recently purchased a TDM400P card with one FXO expansion card, and I'm having problems. The card does not pick up incoming calls. Asterisk detects the ringing line and rings various SIP phones as required. When a sip phone answers, the sip user hears nothing and the PSTN user continues to hear ringing. Here is the asterisk output for an incoming call:

I got this nice TDM22B with two green modules left and two modules right /var/log/messages shows: Nov 26 23:47:48 dns kernel: Zapata Telephony Interface Registered on major 196 Nov 27 00:37:53 dns kernel: Freshmaker version: 71 Nov 27 00:37:56 dns kernel: Freshmaker passed register test Nov 27 00:37:56 dns kernel: Module 0: Installed -- AUTO FXS/DPO Nov 27 00:37:56 dns kernel: Module 1: Installed

I got this nice TDM22B with two green modules left and two modules right /var/log/messages shows: Nov 26 23:47:48 dns kernel: Zapata Telephony Interface Registered on major 196 Nov 27 00:37:53 dns kernel: Freshmaker version: 71 Nov 27 00:37:56 dns kernel: Freshmaker passed register test Nov 27 00:37:56 dns kernel: Module 0: Installed -- AUTO FXS/DPO Nov 27 00:37:56 dns kernel: Module 1:

Hi, can't get X100P (fully zapata compatible clone) to work (I'm in Australia). * recognises the card and the channel (1) but has definetely some problems talking to the pots line. I set up this simple dialplan for ZAP ("incoming" context, as setup in zapata.conf, for channel 1) [incoming] exten => s,1,Answer exten => s,2,Playback(somefile) exten =>

Hi, can't get X100P (fully zapata compatible clone) to work (I'm in Australia). * recognises the card and the channel (1) but has definetely some problems talking to the pots line. I set up this simple dialplan for ZAP ("incoming" context, as setup in zapata.conf, for channel 1) [incoming] exten => s,1,Answer exten => s,2,Playback(somefile) exten =>