similar to: ZT_CHANCONFIG failed on channel 1: Invalid argument (22)

Hi, I just got my TDM400P card (2 modules) and i installed it no probs. The card is detected fine, but for some reason when I add the card to zaptel.conf i get the following error: --snip-- ZT_CHANCONFIG failed on channel 2: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? --snip-- My /etc/zaptel.conf looks

I have had a TDM400 with 2 FXO and 2 FXS working for ages (>12 months). It has stopped working. All four green lights are still lit. I have rebuilt zaptel and asterisk and restarted but the problem persists. /sbin/ztcfg -vvvv Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03:

I've got the latest zaptel and cvs asterisk software loaded on my phone server running FC3. And yes, It's fully updated and udev is setup correctly. I've got a TDM400P with one FXS and one FXO module installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this: [root@asterisk ~]# ztcfg -vvv ZT_CHANCONFIG failed on channel 1: No such device or address (6) Zaptel

Hi i've got an openvox a800p01 with 1 FXO and 4 FSX i've done the following: - downloaded zaptel-1.4.7.1 > >> - downloaded the file opvxa1200.c > >> - copied in zaptel-1.4.7.1/ > >> - edited makefile adding opvxa1200 in the modules and the voice > >> opvxa1200.o : zaptel.h wctdm.h > >> - edited zaptel.sysconfig adding MODULES="$MODULES

My setup: X100P and Quicknet PhoneJack. I can't seem to properly set up a Zap channel for my X100P. Here are some of my configurations: [zaptel.conf] fxsks=1 #X100P fxoks=2 #Quicknet PhoneJack defaultzone=us loadzone=us [zapata.conf] [channels] context=local signalling=fxs_ks channel->1 ;X100P [extensions.conf] ... [local] exten=>_NXXNXXXXXX,1,Dial,Zap/1 ;I'm pretty sure the

Hello. Well I finally rx'd my dev kit (new batch of TDM's apparently. I'm on Mandrake 9.1 There were no hardware install instructions, it would have been nice to know whether the 4-way power connector was to be used or was for some other future or expansion purpose. It came with a floppy disc, no label and it wasn't even write protected. The only readme file was

When I try to start up zaptel, whilst running ztcfg, I get the following error: Jan 1 10:48:18 bu ztcfg: ZT_CHANCONFIG failed on channel 2: No such device or address (6) My /etc/zaptel.conf is: fxsks=1 fxoks=2 loadzone = au defaultzone=au Channel 1 is a X101P card connected to the PSTN and channel 2 is a S100U box driving an analogue phone. The zaptel kernel module gets loaded OK as does the

I had a working Asterisk 1.4.24.1 installation on SUSE 9 Linux but SIP only. I then downloaded and installed latest Zaptel and could not get Zaptel working. So I downloaded Asterisk again and re-installed. But still problems: Here is my ztcfg output: asterisk:/etc/asterisk # ztcfg -vvvvv Notice: Configuration file is /etc/zaptel.conf line 4: Unable to read Zaptel version information. Zaptel

Installing DevkitLite hardware (Very similar to John Lange's post on Tue Oct 08 2002) I cannot get anything to work on the phone connected to the s100u. I dont know what to do. Can someone please help me? I used the sample configuration files from digium documentaion that was supposed to be "sane" defaults for the kit. Very similar to John Lange's post on Tue Oct 08 2002 Here

Hi when I turn on my PC I able to load the drivers and start my card, if I reboot the PC I have the following error ztcfg -vvv Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS Kewlstart (Default) (Slaves: 04) 4 channels

Hi, I'm having problems using a TDM400P Card. I put my SIM card in a Nokia Premicell and connected it to a TDM400P card but when I make calls to the number, it hangs up automatically. The card also can't call out. Any ideas? I've searched the archives without much success. I appreciate all your help. Details: I'm using Asterisk 1.2.17 on Fedora Core release 5 (Bordeaux). On an

Hello, After installing on Ubuntu 10.04 using the tutorial on http://hmontoliu.blogspot.com/2010/03/installing-asterisk-and-freepbx-on.html I have a running instance of Asterisk. PROBLEM: result of dahdi_cfg: DAHDI Tools Version - 2.2.1 DAHDI Version: 2.2.1 Echo Canceller(s): MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2)

Hi: I had an fxo card from Digitnetworks and it was working fine on my Asterisk box. I then replaced it with TDM04B. I changed the zaptel and zapata to include the four channels. When I run ztcfg, I get configuration errors: Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04:

I get the following errors when starting Asterisk. == Parsing '/etc/asterisk/zapata.conf': Found Feb 19 21:14:35 WARNING[10440]: chan_zap.c:920 zt_open: Unable to specify channel 1: No such device Feb 19 21:14:35 ERROR[10440]: chan_zap.c:6860 mkintf: Unable to open channel 1: No such device here = 0, tmp->channel = 1, channel = 1 Feb 19 21:14:35

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

I have two grandstream budtetone-100 and cisco 7960g phones. When I talk via speaker phone on either of the phones I get a lot of echo. Any suggestions? Also how do I turn on the mark echo canceller. -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of asterisk-users-request@lists.digium.com Sent: Tuesday, April 13,

Hello all. I am trying to get my second x100p card set up and am having some troubles. My zaptel.conf reads: fxsks=1-2 fxoks=3-4 defaultzone=us loadzone=us before adding this card my zaptel.conf read: fxsks=1 fxoks=2-3 defaultzone=us loadzone=us But now that I've made the change I am getting the following error when running modprobe wcfxo and of course the same

Hi, I recently purchased two X100Ps and a TMD40B. I have set everything up according to the instructions however I can't get asterisk to pick up an incoming call (It just keeps ringing). Also, when I pick up an internal extension I get dead air. I searched the mailing list for 3+ hours -- What am I missing? Thanks in advance for your help. Here are the installion steps that I used:

[root@server ~]# modprobe zaptel [root@server ~]# modprobe wcfxo ZT_CHANCONFIG failed on channel 1: No such device or address (6) FATAL: Error running install command for wcfxo [root@server ~]# ztcfg -vvv Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address

Hi all, i've installed AMP and Asterisk following the INSTALL file and i have a problem with the TDM04B with 4 FXO: [root@srvoip ~]# ztcfg -vv Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03: FXO Kewlstart (Default) (Slaves: 03) Channel 04: FXO Kewlstart (Default)