similar to: Snom200 -> C7960 noisy?

I had posted earlier asking about a Snom200 communicating with a C7960 and lots of noise in one direction. Turned out the problem was created by me removing the allow=all statement in sip.conf. Someone had suggested that statement is no longer needed, and using allow=ulaw, etc, had an issue where one or more deny's had to be used as well. By adding allow=ulaw in the sip.conf file, the Snom

Asterisk cvs-head compiled 2005-10-07 11: Oct 12 18:35:12 NOTICE[21740]: chan_sip.c:10685 handle_request_register: Registr ation from 'sip:301495906@204.212.194.101' failed for '208.5.218.28' - Not a lo cal SIP domain The sip phone is a Cisco 7960 with one line defined, and registration with * is occuring just fine. Calls to/from the phone are fine. The phone is on a distant

I have multiple voiceage g729 licenses installed on a RH9 box, and have a remote C7960 configured to use it (low bandwidth). In calls like: Remote C7960 -> g729 -> asterisk -> g711 -> C7960 the audio is oftentimes rather choppy. Changing the remote 7960 to use g711 seems to eliminate/reduce the choppyness. Any ideas on what might be behind this?

Using the following defnitions with a C7960: exten => 3001,1,Dial(SIP/3001,15,r) exten => 3001,2,Voicemail2(u3001) exten => 3001,102,Voicemail2(b3001) exten => 3001,103,Hangup If someone is on this phone (real conversation) and another call comes in, the second call goes through the 15 second timeout and is dropped into the 2-priority as "unavailable" (not the 102 busy as

pstn -> sip gw -> * -> C7960 When I dial into * via the pstn, I hear the ivr menu just fine (good quality). I press 3000 (valid extn), and I begin to hear ringing however the ring back is very very choppy. I answer the C7960, and speech is clear in both directions. Place the C7960 extn on hold, and the MOH is very choppy. Checking 'sip show channels' indicates both the sip gw

Someone recently posted the following list as functions built into * *0# sends flash *8# remote call pickup (pickup phone in your group) *67# disable caller id *70# no call waiting *78# do not disturb on *79# do not disturb off *72# enable call forwarding *73# disable call forwarding *82# enable callerid I'm running a CVS from a couple of weeks ago with multiple C7960's, snom 200,

Just received a new Cisco 7960 (not refurb, but brand new) and it won't tftp the initial config file (OS79XX.TXT) from an FC3 box. The 7960 does get an appropriate dhcp response including the tftp address. Using a sniffer, I see the tftp request being sent from the 7960 to the FC3 box, but the FC3 box responds with error code 4 (Illegal TFTP opertion) and an error message of "Request not

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040106/3efdeb9f/attachment.htm -------------- next part -------------- Hello Though my SNOM 200 phone receive a voice mail but it doesn't show MWI on the LCD panel, Instead it keeps displaying "DND SW-REG,Call-log". Though I can access my voicemail using exten

Sorry I forgot the subject in the last post. When my snom200 receives an inbound SIP external sip call, it somehow rejects the call and with a busy tone. The debug shows the following error: channel.c:1142 ast_read: Exception flag set on 'SIP/sipphone-7796', but no exception handler what does this mean and how can I debug it further?? Thanks JC -------------- next

Try this one. Took me a while too. http://www.snom.com/download/share/snom200-2.05c-SIP.bin > -----Original Message----- > From: M3 Freak [mailto:m3freak@rogers.com] > Sent: Monday, May 17, 2004 11:42 AM > To: asterisk-users@lists.digium.com > Subject: [Asterisk-Users] Snom200 Firmware: I only see 2.04g > > Hello all, > > I've noticed several messages about the

Hi, I have just been playing with the latest X-Lite.. It works fine with Asterisk.. As for codecs I tested G.711a/u, GSM and iLBC... iLBC is the only one that didn't work.. not sure why.. But the bigger problem is that when I call another extension that is using a Snom200 the call connects but there is no audio in either direction.. I have tried G.711a/u and GSM and while X-Lite shows that

Hello all, I've noticed several messages about the latest firmware on Snom's site, 2.05b, and today I see that another update is listed, 2.05c. However, when I go to the download page (http://www.snom.com/support_dl_en.php), the latest firmware version available for the Snom200 is 2.04g. Are the newest firmware releases not yet available, or am I doing something stupid? Thanks, Kanwar

Alright, this may seem like something relatively easy to do but I must be missing something or had a neuron misfire. I am trying to get The Status lights on my Snom200 hardphones to display the status of each one of my PSTN lines in my Asterisk server. Current Config: 3 X100P cards Asterisk CVS-02/25/04-18:06:52 5 Snom200 phones I am currently using the following macro to dial out

Look like SNOM have rolled back the firmware version of the 200's from 1.16w to 1.16q.. Anyone know why? -- ______________________________________________ http://www.linuxmail.org/ Now with e-mail forwarding for only US$5.95/yr Powered by Outblaze

On recent releases of the snom200 firmware, the MWI indicator will turn on, but won't turn off when the message has been checked. It works on firmware 2.03o, but not in 2.04g or newer. I filed a bug report with snom, but they're claiming it is an asterisk issue and that it should have been resolved. They suggested that I ask on the list. "Anyway, Asterisk had a bug where it

Two asterisk boxes 150 miles apart, both cvs-head as of this morning (and since Sept 27th), connected via iax2 with low-utilized ds3 internet, C7960 calls exten on remote system (also C7960), and call goes to VM. No other calls in either system (eg, no load). Both boxes have iax config'ed as: trunk=yes allow=ilbc jitterbuffer=yes Recorded VM messages are very distorted. Changing only

Have a strange problem... When a C7960 calls the Polycom ip600, the ip600's first line button blinks, the ip600 display shows the proper callerid, but the phone does not ring at all. If I call the same ip600 from a bt102, the ip600 rings properly. If I call the same ip600 from another C7960, the ip600 rings properly. All phones and asterisk are on the same lan within a few feet. The

(Apologies to those Toronto Asterisk Users' Group folks who have seen this message... I figured I'd have more success with a wider audience) I'm trying to boot a Cisco 7960 from an ISC DHCPD server (3.0.3 on FreeBSD 4.11), so far unsuccessful, and getting some odd behaviour on the wire. I wonder if anyone has done this before and therefore can validate whether or not the traffic I am

Has anyone played around with QoS or TOS relative to * and sip phones? I was just doing a little real-time research and noticed our C7960's mark IP packets with "low delay" and "high throughput" (presumably due to tos_media: 5 in the SIPDefault config file), and rtp packets flowing "from" asterisk back to the sip phone are not marked at all. Is there a * config

Hello all, I am testing CBQ and HTB these days and I got a lots problem which needs your help. It is a little long text :) Thank you! (All my test is based on Redhat Linux9.0) 1.Is isolated of CBQ working? I have read Mr. stef word that he never made cbq isolated work. 2. I have setup an environment to test cbq: one tcp flow which I should protect and a noisy udp flow who will eat much of the