similar to: Double dialing with asterisk and Grandstream BudgeTone-100

I have two problems with Asterisk and my Budgetone 100s. 1. Sometimes when outside callers dial my Budgetone it will ring twice, then the caller will receive a busy signal. This happens intermittently and I cannot pin down the circumstances of when it works and when it doesn't. Asterisk logging doesn't give me too much info when this happens: *CLI> -- Executing

I am setting up a small Asterisk system for use at home. I have one Budgetone 101, one Cisco 7960 and two Xten lite softphones. So far everything is working expect for an issue with the Budgetone. When a call is placed between the Budgetone and any other phone, the call is setup and sounds good. If I hang-up on the Budgetone, everything is ok. If I hang up on the other phone, the Budgetone

Hello, I have a problem with asterisk and Grandstream BudgeTone-100. With default configuration everything works (in anonymous mode and fixed IP), but if Im trying to enable registering, it dos not work. I used 'sip debug' and verbose level 10, nothing happens if I switch telephone on (no messages about bad auth etc). As I understood, after switching phone on at first it will try to

Hello guys, I ask you to share your experience with your BudgeTone 100.... I have my asterisk @ work and I've bought a GrandStream BudgeTone (SIP phone) and I usually use X-Lite I have plugged my BudgeTone into my home network because I want to be called even at home. I succeed to register my X-Lite with Asterisk from home but I can't do that with my BudgeTone. (I don't know

Hi I am setting up an Asterisk System in an office environment, Incoming and Outgoing calls are working ok, but i am having a few strange problems regarding call waiting. With the SNOM 200 (firmware 2.02t) phones, if you are on a call and a 2nd call comes in, the call waiting beep is played and the light flashes, but if you hang up the 1st call, instead of the phone ringing, it connects the

I've looked through the archives - and see questions similar to mine, but no answers. What, if anything, can be done to get the incoming Caller ID to be presented on the Budgetone's Caller ID display? In all other respects the phone+Asterisk seem to be extremely happy with each other.

Hi everyone. I see many posts complaining about Grandstream equipment, so I thought I tell the other side of the story as well. We use Grandstream Budgetone 101 phones in our office and they work extremely well. We have no echo, no crashes, no sudden resets, they "just work". We provision them using TFTP. Our asterisk box has 2 HFCPCI ISDN BRI cards. It's running asterisk 1.2.0 on

Does anyone know what the Grandstream Budgetone is going for $$$ in the US? I didn't immediately see pricing on the phones page. AJ

I have a client using a Grandstream Budgetone 102, but he is unable to register to my Asterisk server. About every 20 seconds, I get the following messages: Aug 11 11:27:17 DEBUG[1087740720]: chan_sip.c:748 __sip_autodestruct: Auto destroying call '3b4b68ec48200ab9@192.168.xxx.xxx' Aug 11 11:27:19 NOTICE[1087740720]: chan_sip.c:7336 handle_request: Registration from

Is anyone using this combination successfully? I have a dell 500sc running rh9 and asterisk 1.0rc1. It is configured with an x100p. I have a Sipura SPA-2000, laptop with Xlite and a Grandstream Budgetone BT-101. I have signed up with Voipjet (they use iax2). I also have an FWD number via iax2. I can sucessfully call back and forth to all devices via zap, sip, and fwd. I can successfully

I know there are several folks hanging around the list that resell VoIP products, I'd be interested in getting your info off-list as I'm trying to persuade someone to get me a budgetone 101 for Christmas ;) I've checked the yahoo site, and they seem to only carry it in white.. Ideally, I'd like blue, so if you have it, please let me know. Also, I've been watching the list for

Symptom: Phone after about 15mins will stop functioning Problem: DHCP lease renewed but default route dropped Fix: Assign a static ip and problem is resolved. Upgrade to new firmware once it is released It turn's out that these phones have a few issue in 1.0.3.81 firmware. The phone may stop transmitting packets if configured with DHCP, if DHCP is being provided by certain devices. Netopia

Just to toss in my very limited experiences with the Grandstream phone-- I haven't tested it enough to really know nor is my Asterisk config set up enough to fully try all the features. Mostly, it just works. It was very easy to configure and get running. I've been toting it around to clients as a show and tell exhibit and it has helped get people excited about the possibilities. Voice

I bought three plus two Grandstream BudgeTone 101 phones. The shipping cost more than the phone itself from Pulver store. The first shipping had one phone defect. Nothing on the display. (Can happen!) The second shipment had one phone with a defect display, but it still worked. The second phone's handset was defect too (microphone did not work). Changing the handset from this one to the

Hi there, I'm having problems with the Grandstream Budgetone 101 on hangup - "show channels"/"show channels concise" output is still showing the call's channels as active. The problem does not exist when I use SJPhone, so I'm assuming it isn't an Asterisk configuration issue. Has anyone seen this, or better, does anyone have a fix? :) Thanks, David. --

After reading about these $75 SIP phones on this list, I purchased a couple for evaluation. They do work with asterisk - and are good value for money, but as somebody commented: they are not yet perfect. I just wondered if anybody had managed to get either the message-waiting indicator or the conference button to work? Phil Skuse <phil.skuse@vicorp.com>

I'm using tftp server that automatically loads on each reboot, for some reason the last 2 files fail to load each time. (and I think this has always been the case) Aborted 192.168.16.32 C:\Program Files\TFTP Desktop\1.0.5.18\cfg000b82005c24 Octet, Send 192.168.16.20 25 Jan 18:25 Error Aborted 192.168.16.32 C:\Program Files\TFTP

I'm using 1 BudgeTone 100 IP Phone and a Sipura 2000 for all my old analog phones. The analog phones with the Sipura seem to work great. Voice quality is fine on both ends on the Sipura. I'm using the Teliax service and I use the Ulaw codec for all phones. However, I'm struggling with the BudgeTone 100. On my end, I find there is lot's of voice cut outs. I'm told my

Hi Guys, Sorry about writing to that list but could not find better place. I have Grandstream BT-100 phone, btw, was working great with Asterisk. I have upgraded the phone, and during upgrade something went wrong. Right now when I power the phone I can only see some garbage on the LCD display. does not react on any buttons, pings,..... Maybe somebody has any idea if it is fixable or I can just

I logged a bug I wanted to see if anyone else is having this problem or if it's just me. http://bugs.digium.com./bug_view_page.php?bug_id=0000486 I just downloaded the newest version from CVS(Tuesday@~7pm) and I am getting an error whenever I call the asterisk box. I cannot here any audio on the budgtone. This works fine with my pingtel phone and my sip 7960. Also if I call my Skinny 7960 it