similar to: Using a Cisco 7960G

Hello all, Please forgive me if this sounds a little (or a lot) ignorant as I am very new to asterisk. Right now I have two pc's connected back to back through an E100 card running asterisk. I have openh323 running as well and I am able to route calls through the E1 line. Next up I would like to be able to register asterisk with a gatekeeper. On another computer is running openGK. Using

Use oh323. Download the openh323 and pwlib tarballs from openh323.org Follow Jeremy's instructions in the /asterisk/channels/h323/ directory EXACTLY! good luck Regards, Sean Langley, P.Eng Firmware Engineer General Dynamics Canada (403)730-1482 sean.langley@gdcanada.com > -----Original Message----- > From: Senad Jordanovic [mailto:senad@cwcom.net] > Sent: Friday, September 12,

Just purchased a couple of T100 and E100 cards in order to interface from our company's proprietary system through a linux gateway. I am new to Asterisk and Digium. After installing the T100 card, I went looking for drivers for this card. Are the drivers built into the Asterisk application? If so, how do I enable the card through Asterisk? Are there any good getting started documents for a

Hello I am a newbie to Asterisk. We have set up Asterisk on a PC with Redhat 9.0. We have installed H323 openphone on our PC's. We are wondering what a gatekeeper does. It seems we need one but what I have seen in this group is that a gatekeeper must be installed on another box on the network. As all our PC's on the network use Microsoft OS is there a free gatekeeper software for

On Mon, Jun 12, 2017 at 7:30 PM, Langley, Robert <Robert.Langley at ventura.org > wrote: > As far as the peer status (and I now remember seeing this earlier) the > issue appears to be that the host name for gsaov07 is attempting to resolve > over the wrong network for gluster "ent...." and not "stor.local". > So, it may be as simple as removing gsaov07 as a

As far as the peer status (and I now remember seeing this earlier) the issue appears to be that the host name for gsaov07 is attempting to resolve over the wrong network for gluster "ent...." and not "stor.local". So, it may be as simple as removing gsaov07 as a peer, then probing over the correct network. I'll follow up with the Engine log. Sent using OWA for iPhone

On Mon, Jun 12, 2017 at 6:41 PM, Atin Mukherjee <amukherj at redhat.com> wrote: > > On Mon, 12 Jun 2017 at 17:40, Langley, Robert <Robert.Langley at ventura.org> > wrote: > >> Thank you for your response. There has been no change of IP addresses. >> And I have tried restarting the glusterd service multiple times. >> I am using fully qualified names with a

Thank you for your response. There has been no change of IP addresses. And I have tried restarting the glusterd service multiple times. I am using fully qualified names with a DNS server that has forward and reverse setup. Something I had noticed is that, with oVirt, communication is being attempted over the VM network, rather than storage network. Which is not how the bricks are defined. Not sure

On Mon, 12 Jun 2017 at 17:40, Langley, Robert <Robert.Langley at ventura.org> wrote: > Thank you for your response. There has been no change of IP addresses. And > I have tried restarting the glusterd service multiple times. > I am using fully qualified names with a DNS server that has forward and > reverse setup. > Something I had noticed is that, with oVirt, communication

glusterd failed to resolve addresses of the bricks. This could happen either because of glusterd was trying to resolve the address of the brick before the N/W interface was up or a change in the IP? If it's the latter then a point to note is that it's recommended that cluster should be formed using hostname otherwise if the server goes through IP change we have to change the configuration

Hi there I am using an IAX2 softphone built from the IaxClient library dialing into Meetme conferences. The IaxClient seems to use silence suppression, and not sure if this can be disabled. The client works fine through most routers, but for some it disconnects the client after about 5 minutes and gives this error in the asterisk logs: Chan_iax2.c:1480 attempt_transmit: Max retries exceeded to

Hello All, Eric Langley here with my first post to this list. I am looking to determine if R is suitable for a development project I am working on and if so possibly finding someone proficient in R that would be interested in doing the coding. I would like to preface my inquiry that while I am not a programmer I can communicate in a dialog my objectives. An array of rank ordered data looks like

Hi, I am implementing and audio recorder where I need to encode to vorbis DURING recording. I need to allow the user to cut and paste segments of encoded audio into a new stream. As such, I need to encode the audio in sub-second pages (the smallest allowable amount for the wave format), so that cut/paste can be implemented simply by re-arranging these encoded pages. How can I calculate, the

I have the following in extentions.conf: exten => 2111,1,Dial(SIP/2111 at gw1.langley) exten => 2111,2,Voicemail(u2111) exten => 2111,3,Hangup exten => 2111,100,Voicemail(b2111) exten => 2111,101,Hangup I have the following in sip.conf: ; Cisco 1750 [gw1.langley] type=friend host=172.16.17.1 context=default canreinvite=no Like the ATA, lots of stuff doesn't work on the 1750

This is in relation to bringing up a new oVirt environment. When I was bringing up oVirt (Hosted-Engine), I had the Glusterd service stopped, since the server (I have its name as GSAoV07) was initially only going to be used to host the oVirt engine as a hypervisor (it will have Gluster volumes in the near future). I have three other servers I am using for storage. One of those three is also going

Hello I am trying to read a large number of WinZip files from inside R (v 1.7.1, options()$unzip = internal). I have unsuccessfully tried to unpack the files and write to an external directory so that I could read the text files using zip.unpack. Reading some of the archives suggests that this is for .ZIP format files only. I have also unsuccessfully tried to use gzfile to open a connection and

Dear Telcotype Braniacs, I have tried doing a google search to find out what this switch looks like, what the physical interface is, but havn't been successful. I am quite new to the ISDN world so I'm not sure what to expect when I see this switch. Does anyone have any experience connecting to this switch? The following is basically all I have been given for info: 1) Ericsson, AXT121,

Hi there I am currently using Asterisk with Meetme on a 2.4 linux kernel. I am using Ztdummy with usb-uhci driver for timing. It seems to work ok, although I haven't tried it with more than 5 users. However, I am now looking to move into a production environment and some people have said that it is better to have a Zaptel card. I would be installing Asterisk on a 2.6 linux kernel for the

Hi I appreciate there has been some recent discussion regarding generating publication quality graphics in R. I am fairly familiar with these issues and have had no problems generating high quality images from R windows version. However, I have recently install Vista and what previously worked well under XP now looks substandard when generated from R (using tiff(), jpeg(), etc) and I haven't

I am designing an application to run a fishing tournament I am hosting. Each fish entered will be given a point total based on the length of the fish and the species of fish. Each species has a point multiplier. For Example Trout have a multiplier of 10 so a 20 inch Trout would have a score of 200. My conundrum is in where and when do I calculate the points. The options I have come up