similar to: Cant locate my X100P

Hi all, I have just purchased the DevKit from Digium and received a X100P and a TDM400P (it has one FXS module). The problem is that I can't get the kernel module (wcfxs) to load and run. I have searched the archives and can't find anything about this. Do the messages below ring any bells with anyone ? There is no interrupt clash (see pci list below). I am running on a AMD 1.2G

Hi all, I have installed a TE110P in a BOX but when I load zaptel module I can't see any device in /proc/zaptel. And led of the card is green. My zaptel.conf is the next: span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone=es defaultzone=es and cat /proc/pci throguh next: PCI devices found: Bus 0, device 0, function 0: Host bridge: Intel Corp. 82845 845

Thank you for the suggestions Andrew. I have not come across some of them before and will give them a shot. Based on my reading, changing the motherboard should have minimal impact unless that motherboard and the TDM400P don't get along (aka. IRQ sharing). I have disabled everything that is not needed and I do not believe I have any IRQ problems and I am NEVER wrong ;). Calls are crisp and

Thanks in advance root@asterisk01:~# modprobe wcfxo /lib/modules/2.4.20/misc/wcfxo.o: init_module: No such device /lib/modules/2.4.20/misc/wcfxo.o: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.20/misc/wcfxo.o: insmod /lib/modules/2.4.20/misc/wcfxo.o

Hi List, I am looking for good multifunction (fax, scanner, ..) color network laser printer for Linux, any ideas? specs: - Linux, Windows and OSX support on printer and also on scanner. - A4 papersize http://multi.gnt.lt/Pages/brochures/HP/CM2320MFP-ENG.pdf ? thanks, -- Eero

Hi ! I''m tryng to install a windows instance to a ganeti cluster. For the moment, i have configured ganeti2, i have created a debian instance with debootstrap OS, i have created a windows instance with xen commands, with a HVM processor. I have already initialize too my cluster with HVM and PVM option. However, i can''t create a windows vm with ganeti2. my command is:

Hi Last week I installed Asterisk (release1) with digium t100p single span T1 (wct1xxp) board on Dell GX270 pc configured for PRI. Asterisk/t100p is currently the only user of the t1 line. All worked well for about a half a day, PSTN to SIP phones to non-SIP IP phones etc. Alas, since then I consistently get multitudes of blue alarms on all b-channels followed by a loss of d-channel: Aug 31

> -----Original Message----- > From: Kurt Heinrich > Sent: Thursday, 4 May 2000 14:29 > To: 'samba@samba.org' > Subject: Browsing issues NT WS 4.0 and Samba > > Hi Guys/Girls, > > I have recently been trying to implement samba into our environment here > as a replacement for ftp clients. > > What I am finding is that windows explorer (NT W/S 4.0)

Hello, I guess it possible distro specific issue but is it resolvable? I have one node(testing purpose) ganeti 2.0.1 cluster installed over Debian5 Lenny. Almost everything from distro repositories. Only ganeti 2.0.1 and ganeti-debootstrap are from sources. I have it successful run with vmlinuz-2.6.26-2-xen-686 and initrd.img-2.6.26-2-xen-686 from repositories. Both Dom0 and DomU are use the

Hello * users I've problems with sound quality on zaphfc Asterisk works fine good sound quality. If I do "make load" in the bristuf.xx zaphfc dir then sound quality drops directly. Even if I don't load the chan_zap in the modules.conf I use this config on more (even old 400Mhz machines) and works correctly. Looks like an hardware problem but I can't find it. I don't

This patch contains fixes for persistent grants implementation v2: * handle == 0 is a valid handle, so initialize grants in blkback setting the handle to BLKBACK_INVALID_HANDLE instead of 0. Reported by Konrad Rzeszutek Wilk. * new_map is a boolean, use "true" or "false" instead of 1 and 0. Reported by Konrad Rzeszutek Wilk. * blkfront announces the

Hi All, Googling X100P Clone I found several information about these cards and seems that some winmodem has the same chip used from the original X100P. Here below a list winmodem which should work as X100P clone: 1057 Motorola 5608 SM56 PCI Fax Voice Modem E159 Tiger Jet Network Inc 0001 Tiger 300/320 PCI interface I bought one "Trust 56k V92 PCI Internal Modem MD-1100" which has the

Hi, One of my pbx's seems to be having some new issues. crackling interference on the zap channels running through the channel bank, and I noticed that these happen when I hit an "irq miss" in zttool: Current Alarms: No alarms. Sync Source: Digium Wildcard T100P T1/PRI C IRQ Misses: 82695 Bipolar Viol: 0 Tx/Rx Levels: 0/8 3 Total/Conf/Act:

This is a cherry pick of two patches that add support for guest paged out frames in the XCP 2.6.32 dom0 patch queue. First patch propagates the ENOENT returned by the hypervisor in the case of a paged out page, all the way up the call chain to the MMAPBATCH_V2 ioctl. The ioctl is mainly used to harvest those return values and retry. The second patch adds retry loops to all backend grant

Hello all, has someone worked with DRBD (http://www.drbd.org) for HA of mail storage? if so, does it have stability issues? comments and experiences are thanked :) Thanks, Rodolfo.

Hi Guys/Girls, I have recently been trying to implement samba into our environment here as a replacement for ftp clients. What I am finding is that windows explorer (NT W/S 4.0) will not list all the files in the directory or in fact all the sub directories either. It is quite unusual, one of the shares we have contains two directories sun and suntst. They are basically mirrors of each other (

I'm having some trouble here - need some help! I've just bought a TE405p (32-bit 5V), but cannot get it working in a dell 6450. The dell has (from tech specs) "three peer PCI buses: two 64-bit buses and one 32-bit bus Expansion slots seven hot-pluggable PCI slots (two 64-bit/66 MHz, four 64-bit/33 MHz, and one 32-bit/33 MHz)" I cannot get the card working in any of the slots.

I installed a 2 port serial PCI card on a system running CentOS 4.3, but I can't get the additional serial ports to work. The card I used is from StarTech (http://www.startech.com/Product/ItemDetail.aspx? productid=PCI2S550&c=US). When it is detected by kudzu, it shows up as a "NetMos Technologies PCI 9835 Multi I/O Controller". I've included the output of

Hi, When running domUs with pygrub, I get errors: .... xen be core: xen be core: can''t open gnttab device can''t open gnttab device xen be core: xen be core: can''t open gnttab device can''t open gnttab device xen be core: xen be core: can''t open gnttab device ..... domUs start, but these errors continue on dom0 Configuration: dom0: Ubuntu 8.10

Asterisk doesnt answer the ringing phone, so according to some doc that I read I should try and see if I get I/O on /dev/zap/1. I dont see any from cat /dev/zap/1 while it is ringing or otherwise. Dmesg seems to have a few odd things (out of space), not sure how relevant. Does anyone have any ideas? Here is my info: <built zaptel / asterisk CVS from 2 days ago> [root@homestar etc]#