similar to: trying to make a X100P work

Hi, I have two X100P cards in the same system. I can use both of them to initiate and/or receive PSTN calls. I want now to define separate context for each of them, in oder to route inbound calls to different extensions. This is what I have now in zapata.conf file: [channels] language=en context=inbound-analog signalling=fxs_ks usecallerid=yes callwaiting=yes echocancel=yes

PROBLEM: My x100p only does bad things. When I plug the line from the wall into the card, other phones in my house go nuts, no dialtone, crazy clicking, random tones, etc. Following the steps below, the line is screwed up any time I test after step 2. Just plugging the line from the wall into the x100p takes my other phones off line. External calls to my line hear busy. Obviously, can't

Hi, I just got two digium x100p clones and installed asterisk on fedora core 2 which took some tweaking. After getting asterisk up I installed the zaptel stuff - then modprobed zaptel, wcfxs (for the fxo cards), which worked fine. ztcfg is showing two channels configured, but when I start asterisk and do show channels, i see no active channels. zapata.conf has: signalling = fxs_ks

I have the following: Call -> PSTN -> * -> GrandStream 101 1.0.3.81 The GS displays "ohn ro n2600" when the call is past to the GS. If I pass the call to a XTEN client, Caller ID shows up. Any ideas ??

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

Hey all, ? I'm trying to get an E400P and 2 X100Ps working together in the one box and don't seem to be having much luck. ? I can get the two different types of boards working separately, but not together.? I've made calls on both the X100P and have seen sync and correct signalling on the E400P.? But when I try to enable to configs together I get the following: ? modprobe wcfxo

So I took a chance with an X100P knock-off on eBay. I'm running Asterisk + FreePBX on a PowerMac G3 (beige desktop) using Slackintosh 10.2 and kernel 2.6.16.16. Everything has been fine up until now. I compile the 1.2.5 Zaptel drivers without a problem, get the udev configuration in, modprobe zaptel, and finally modprobe wcfxo. At this point, I get the message: ZT_CHANCONFIG failed on channel

Hi. I have a x100p card installed on my asterisk box... my zapata.conf file includes the following lines: [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 echocancel=yes rxgain=0.0 txgain=0.0 group=1 callgroup=1 pickupgroup=1 Basically, the zapata.conf file generated by make samples. Then in my extensions.conf I have this: [default] include => demo And demo is

So I'm not getting caller ID via the X100P card. I've confirmed the PSTN is sending me caller id by plugging in a little third party box. Ideas, tips, greatly appreciated

I have two X100P cards that were working just fine for months. When I run modprobe wcfxo today I got the following error: ZT_CHANCONFIG failed on channel 2: No such device or address (6) /lib/modules/2.4.19/misc/wcfxo.o: post-install wcfxo failed /lib/modules/2.4.19/misc/wcfxo.o: insmod wcfxo failed The output of dmesg said that wcfxo:Out of space to write register 06 with e0. What?s

I am starting to dip my toes into the asterisk world, and to that end I've scavenged an old PC (this is a home project, and I have basically $0 to spend on it), and installed FC1. I've purchased a clone X100P (or at least I was told it was), and I am trying to get it to work. However, when I try and load the wcfxo module, I get the following errors... [root@loudhoward root]# insmod

All, I'm having trouble getting the X100P working. Lsmod shows : zaptel 179808 0 I did a . # modprobe zaptel and here is my zaptel.conf (comments omitted) __SNIP__ fxsks=1 loadzone = us defaultzone=us __SNIP__ Here is zapata.conf __SNIP__ [trunkgroups] [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 usecallerid=yes hidecallerid=no

Hi, I have already installed the X100P drivers but when I make to make call call, I always get No channel type registered for 'Zap'. Any idea how to solve this problem? It seems that the Zap module is not loaded but I have already load the driver by modprobe zaptel > modprobe wcfxo > ztcfg -vv thanks -------------- next part -------------- An HTML

Hi! The X100P is working - partly. I can make outgoing calls. But the card has got a problem detecting incoming calls. Even in verbose mode I don't see any hint that the card detects a call. At the moment I'm using the card behind my old ISDN telephone system. Could it be a problem with the line voltage? Can I adjust anything when loading the kernel module? Bye! Michael

Tengo en una maquia ubuntu 8.10 el kernel es Linux 2.6.27-14-generic Quiero configurar una tarjeta x100p i usarla con asterisk, asi que descague compile e instale lo siguiente: asterisk-1.4.24 dahdi-linux-2.1.0.4 dahdi-tools-2.1.0.2 libpri-1.4.9 Sin embargo no logro configurar la tarjeta con exito, ya probe casi? todo. Esto aparece si ejecuto lspci: 04:06.0 Communication controller: Motorola

Thanks for the reply Bill. I am aware of the interrupts problem. To solve it I have already disabled my serial ports freeing up interrupts 3 and 4 and these are allocated to the two cards. This was done 2 months ago and has not solved the problem. Is there any way that something can wake up every now and then and generate these two interrupts? My current /proc/interrupts is as follows:

I'm attempting to configure a machine with a DevKit Lite (X100P & S100U). After I modprobe wcfxo, the machine goes into some kind of loop after about 10 seconds, where it spits out what appears to be 32-bit addresses, ad infinitum. At this point, the machine becomes completely unresponsive to keyboard input (i.e. Ctrl-C, Ctrl-Alt-Del, even CapsLock and NumLock states [lights] cannot be

Hi, I'm cutting my teeth setting up a home asterisk server, but having some trouble getting Zaptel to recognize a X100P clone PCI (Motorola SM56 which should work according to various wiki's). What struck me was that the "/proc/interrupts" do not include IRQ 11 as the "lpcpi -v" is reporting. Am I missing something fundamental here? Any hint is greatly

I've just installed a Digitnetworks X100P clone in my * server and run the install script for the voicepet-single-x100p tarball. The install appeared to run OK with modprobe wcfxo successful and the ztcfg reporting "Channel 01: FXS Kewlstart (Default) (Slaves: 01)". When I try to start * though I get a segmentation fault after loading res_features.so. I discovered that the

What can I do because my X100P don´t answer sometimes. I put these parameters in the zapata.conf, but sometimes my X100P don´t answer. usedistinctiveringdetection=yes dring1=363,137,0 dring1context=incoming2 Any sugestion? Thank´s --------------------------------- Do you Yahoo!? New and Improved Yahoo! Mail - Send 10MB messages! -------------- next part -------------- An HTML attachment