similar to: Conference + E100P + H323

hi, Can anybody pls tell me, how to increase the time gap between 2 digits when you transfer a call. ie, the operator answers the call, and presses hash key to transfer, and then enters the extension number, some times, it timeouts too quickly before the operator enters the whole extension number (may be bcos the operator is slow). I tried the following, but it doesn't seems to be helping

Hello Conference again. Meetme can now limit number of users in a room. Can it also limit how long a conference session? Someone ask the same question (from achive) but doesn't have a solid answer. Foong -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030821/c1ca1383/attachment.htm

Hello all, Can I execute linux command like(ls, mkdir) through the Manager interface? I can't seem to access the manual at digium.com. I keep getting 'Forbidden' error. Looks like they are upgrading or something. CF

Hello, Does asterisk supports VXML? Couldn't find much resource on that on google and wiki. Thanks Foong

Hi, I'm installing my first E100P. My zaptel reads the following: Span=1,0,0,ccs,hdb3,crc4 E&m=1-31 My Zapata.conf reads the following: Signaling = em_w Channel =1-15 Channel =16-31 After starting the zapter service I get: ZT_SPANCONFIG failed on span 1: No such device or address (6) ??? PauloHM -------------- next part -------------- An HTML attachment was scrubbed...

Hello, I have 5 digium's g.729 codecs and succesfully register with asterisk, I have incomming call from my cisco AS5300 to Asterisk through IP. But Asterisk always use g711 ulaw instead of g.729. When I disable all other codecs other than g.729 in both cisco and asterisk, calls get dropped once connected. The codec list show on my cisco AS5300 for g.729 are: g729r8 g729br8 I suspect that

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

Hello all, I have a cisco AS5300 which is register with a gatekeeper and a Asterisk server also register with the gatekeeper. PSTN ---->AS5300 ---->Gatekeeper ---->Asterisk I set up a conference room on the Asterisk sever (Room No 1234). I try to call from PSTN to AS5300, The AS5300 will call the Asterisk server through the gatekeeper. I manage to get to the start of the conference

Hello, When I have the following extension: exten => 900,1,dial(Zap/0122740900) can I know whether 'dial' actually gets through or the called party is busy at the moment. I want to perform different action based on whether the 'dail' success or not. Foong -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, Is there a asterisk developer guide/source code doc or something like that? I want to see if I can implement the admin menu function for meetme. Foong -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030922/3ff8a388/attachment.htm

Hello, I have been using IAX to serve clients endpoints for a while with no problem. But recently, to increase the bandwidth to the Asterisk server, I add another network interface card to my Asterisk server which connected to a different service provider that I currently have. Both of my nic is assigned different public ip. the client will actually choose one of these ip and authenticate itself.

Just cross pairs 1-2 and 4-5 1 <--> 4 2 <--> 5 Never done an E1, but I think it's the same for a T1 4 wire cable. Tim Thompson Commercial Sales Engineer http://www.amatechtel.com (806) 722-2227 -----Original Message----- From: bam [mailto:bam@cqm.co.uk] Sent: Monday, December 29, 2003 9:12 AM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] E100P pinouts

Hello ml, i need some help on my zaptel configuration. My E100P only shows some YELLOW / RED alarm when I load the wct1xxp module and do a cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS YELLOW RED ... .. . My /etc/zaptel.conf is: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=nl defaultzone=nl I tried zaptel-1.0RC2 and the latest CVS

hi see below's conversation. it seems the e100p card doesn't work with BT. Any idea how this'll work against Telenor (norway)? roy <RoyK> does anyone know if I can trust the E100P to do full PRI stuff in .no? <cypromis> dunno about no <cypromis> I cannot use it in UK <cypromis> cause the framer has problems with system-x switches at bt

Hi, i just received an E100P, this is the first one I have ever seen, and notice that the board reads T100P. Is this right ? The antistatic bag had a small label that has E100P written on it, and the card is a bit different than the T100P I already have, Does Digium use the same boards for both cards ? I don't have an E1 link here, can I test the card just by loading the driver and run

Hello list, i've got some problems getting a E1 line with a E100P up and running (germany). # cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS/CRC4 YELLOW RED "YELLOW RED" sounds not so good. When launching asterisk, enabling pri debug on that span, i see outgoing attempts: ;---------- snip -------- > [00 01 7f ] > Unnumbered

Hi ! I am trying to configure two E100P cards, but I am a bit confused with zapta.conf in what I am trying to achieve. The * will be connected to a pstn switch with two E1 PRI lines. The E1 lines will be used for incoming calls as well as outgoing calls. My problem now is what to put in zapta.conf, I would like to group all channels from both cards together (if that's possible). Does this

Hello, I am recently inspecting the IAX protocol.. I wonder if there away to associate a user name to a number say I have a client register to the IAX server with username 'John' and I want to associate a number say '12345678' tho John so other register users can call john by dialing 12345678. Something like the H323_id and the E164 alias in H323 protocol. Foong --------------

Hello All, I wonder is there a way where I reload asterisk on CLI without disconnect any call that is currently taken place. Foong -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030813/41f0a4ca/attachment.htm

hi All, quit new to asterisk, can anybody tell me whether Wildcard E400P and Wildcard E100P support R2 CAS protocol. if they do, what is the value, i should set to 'signalling' parameter in the zapata.conf file? Surajee -------------- next part -------------- An HTML attachment was scrubbed... URL: