similar to: Digium & PCI-X

I've got a * box with a TDM40B and an E100P. The E1 is connected to a Shout900 VoIP gateway from net.com. My question is, when I place a call from an analog phone and that call is routed over the E1, what encoding is used? And do I have any control over that? I'm obviously not an expert here, but the Shout900 vendor is claiming that some difficulties that we are having with integration are

I'm wondering if anyone has had any good/bad/indifferent experiences with Supermicro P4SGE P4 FCPGA motherboards and Digium cards? I'm looking to use this MB in an E100P E1 card solution, and I haven't had the ability to test with that configuration before I ship a system overseas (since I don't have an E1 to plug into it, it's hard for me to test, and I don't have

This might be a newbie question but I'm just wondering how would it be possible to have 30 analog lines using asterisk for PBX by just using TDM40B and X100P (or are there any device>), if an ordinary PC support just 4 PCI slots? the maximum scale i guess would just be 2 x 8. Adding a new PC just for this purpose would be costly. I would appreciate your comments. Thanks.

Hi all, Does anyone run Asterisk on FC4? with Digium's TDM40B cards. any success stories? my Intel 865 M'd+ Intel 3.0GHz freezee during installation (FC4). Please any comments? Kumara

Hi All, I recently purchased the Asterisk Developer's Kit (TDM) to try out Asterisk. After following the directions in the Digium's FAQ topic entitled "Q. How do I configure my TDM40B and X100P?", I'm receiving the following error: WARNING[1074428608]: File chan_zap.c, Line 6748 (load_module): Ignoring rxwink ERROR[1074428608]: File chan_zap.c, Line 6692 (load_module):

Morning, I've installed asterisk on FC4 and had a few problems with zaptel stuff. Having installed it on SuSE I was able to check a few things that were different. When installed with the RPMS, the udev stuff gets put into the normal 50-udev file under /etc/udev. On SuSE, it worked when the necessary zaptel section was in a separate file name 55-zaptel.udev (the name is arbitrary,

Hello, Thanks to members of the list things changed on my installation (asterisk + digium E100P with of course an E1 line). Here is my zaptel.conf : - span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=fr defaultzone=fr - Output of zttool: - Alarms Span YEL/RED Digium Wildcard E100P E1/PRA Card 0 - [root@asterisk root]# head /proc/zaptel/1 Span 1: WCT1/0 "Digium

I'm installing my first Asterisk server. I have a TDM04B card installed in my asterisk server (4x FXO ports). I have 5 Cisco IP phone 7960 working fine on asterisk using SIP. My configuration to receive call is working as expected meaning anyone calling on one of the 4 FXO ports is answer by asterisk and asked to enter the extension of the person to reach and then it is transfer on the

Hello ml, i need some help on my zaptel configuration. My E100P only shows some YELLOW / RED alarm when I load the wct1xxp module and do a cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS YELLOW RED ... .. . My /etc/zaptel.conf is: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=nl defaultzone=nl I tried zaptel-1.0RC2 and the latest CVS

Hullo everyone, Iam new to Asterix but am trying to get R2 signalling working with a Digium E100P E1/PRA Card. My Telecom doesn't have an implementation of ISDN PRI yet, so it's R2 that is supported. Could anyone have a patch to fix this for me. Am told it has something to do with Assembly Language programming. Please help me fix this. Regards, Nicholas

Firstly, the problem... Ever since I installed and setup asterisk, I have had various problems, initially it was echo caused by the ISDN (isdn4linux) card I was using. So, I upgraded to the X101P from digium. I still had echo, so I figured it was also caused by the ATA186 (cisco) I was using. So, I upgraded again to the TDM40B quad FXS card. This solved pretty much all my problems, except

Hi All, I Have a Digium Card TDM40P, the specification say: OEM TDM40B: TDM400P + 4 PORT FXS Bundle, my question is: Can I to install analog lines of PTSN?, other detail is: this card have 4 card green. I need to know what is the best card for the following scenario: I need a IVR for my comapny and a PBX, but i want that my extension not use FXS I want IP phone . Thanks ins advanced,

Hello all. My company currently has an older Executone PBX system that we are outgrowing. Rather than wait until the last minute to make a hasty decision, I thought it would be a good idea to do some research and compare options first. My expertise is in computers and networking, and telephony systems are mostly foreign to me. What we currently have are 5 incoming POTS lines and 25

Hi, I just bought the E100P from digium. It has both keys: 3.3V and 5V, so it would fit both, in a 5V-PCI slot and in a 3.3V PCI slot. Is it true, that I can plug it without destroying it in an ordenary 5V PCI slot? Roger.

Hello, I am having problems configuring a TDM400P 4 Port FXO card with groundstart signalling. The box has 2 X100P's, 1 TDM04B and 1 TDM40B. I can configure it for loopstart and it works, just not groundstart, which I need for this installation. What am I missing? Thanks! Mark /etc/zaptel.conf #two X100P FXO Cards # fxsls=1-2 # TDM400P 4 Port FXO (TDM04B) fxsgs=3-6 # TDM400P 4 Port

G'Day, I need from regarding using the X100P. Some are specific to Australia and I have been told in IRC there are already existing users in oz, so I would appreciate your input. 1) Is the X100P Australia telco approved? 2) I have setup asterisk with X100P and whenever I dial in I cannot get any callerid information. Is this standard behaviour? If not how have other australian users managed

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

Hi, I get the following message when I try to run Asterisk. This happened after I changed some of the configuration files: extensions.conf, zaptel.conf and zapata.conf. I have both TDM40B and X100P cards and am trying to use them together. Please let me know if there is something else I should do. Thnx, Gladys [chan_local.so] => (Local Proxy Channel) == Registered channel type

Hola! I've a Digium E1 card, zaptel recognizes it as (loading the module with debug=1) Setting up DMA (write/read = 321b2000/321b2200) Controller version: 43 Framer: DS21554, Revision: 5 (E1) Found a Wildcard: Digium Wildcard E100P E1/PRA Using CCS/HDB3 coding/framing with CRC4 120 Ohms Calling startup (flags is 4099) Started DMA Got interrupt: 0x0005 /etc/zaptel.conf:

Hi.... Apologies for the length of this, but any help would be greatly appreciated ;-)... I have installed and configured a Digium E100P on my Asterisk PBX and I have connected this to an 8 port E1 VoIP gateway on a Cisco 6509. There is also an external E1 link from our Telco plugged into one of the other ports on this gateway and this gateway is in turn registered with a Cisco CallManager