similar to: Fix for Redhat 9 zombie AGI processes

I've had the same thing happen, only on the single port T1 card and a channel bank, and one of the FXO channels also having a phone attached elsewhere... I just wound up putting that channel in a different context and running Exten => s,1,Hangup (I'm just using the line for outbound dialing) -----Original Message----- From: asterisk-users-admin@lists.digium.com

My new company is going to enter a bid competing with 3Com and Siemens solutions from others. Voice service is a PRI T-1 with a block of 100 DID numbers, a second T1 that will carry Integrated voice/data, 12 voice/768K for redundency. I asked this a week or two ago, now I have more details. Best/$ channel banks that work with Asterisk and Best deal on phones... 16 business, 34 basic IP

My system seems to be generating a call on its own... Unfortuately I can't give much more information.. I have an X100P and an S100U.. My Modem and the X100P share a common line.. When I am on the internet (which is most of the day) * just sits there and does nothing (apart from when I am testing ideas for the dial plan), but at night when I am sleeping and the modem is not connected then

Hi all- Over the past week or two, I've been trying out asterisk under Fedora 1 Linux (RedHat). In my setup (single and dual Xeon motherboards), I have so far had a very good experience in terms of performance. In doing E1 load testing, I've found that Fedora handles heavy load much better than RedHat9, probably because of its better use of the multi-threading capabilities of the Xeon.

Hello- What is the .gsm format? Ie: what's the encoding method and sample rate please? Thanks Scott Scott M. Stingel Emerging Voice Technology Inc. Palo Alto, California and London, England Email: scott@evtmedia.com URL: www.evtmedia.com

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

Hello- Is it possible to set the CDR record field called "accountcode" from within the dialplan? Or is there another way to cause this field to be set, preferably without using AGI code. Thanks Scott Scott M. Stingel Emerging Voice Technology Inc. Palo Alto, California and London, England www.evtmedia.com

Hi- I'm almost embarrassed to ask the following simple question, following John's excellent and rigorous bandwidth analysis (see earlier thread): I have a straightforward Asterisk application, IVR-only (no connections between channels). It will simply decode DTMF's and speak prompts (probably A-Law encoded) on a number of E1 circuits simultaneously. Realistically, how many

Hi all- This question is for those familiar with EuroISDN setup. I have a customer in Europe where I'm going to install an asterisk based system with 4 E1's. The customer will configure them all in one large hunt group. My question is about the E1 channel configuration. I know that usually single E1 spans are set up with 30 channels (1-15 and 17-31) as the voice (bearer) channels and

Hi- I have posted a photo of the TE410P Digium card on my site, so that those wishing to purchase a compatible motherboard can see physically what the PCI slot requirement is: http://www.evtmedia.com/TE410P.htm I believe the required slot is a 64-bit, 3.3 Volt PCI, most commonly found on Xeon-based motherboards. A 64-bit slot is longer than the TE410P board requires, but the PCI connector

Hi- I have an upcoming order for a bunch of asterisk boxes, and I'm considering using an "assembled" package for the server, instead of building them from components as I usually do. Does anyone have experience with the Dell PowerEdge 750 server, or any other 1U rackmount server for use with asterisk? Thanks in advance Scott Stingel Scott M. Stingel President, Emerging Voice

Hi- I'm looking for an appropriate system board to power a system with two (2) Digium TE410P cards. Since these cards require the 3.3 volt PCI, I'm considering vendors like Tyan for the motherboard. Can anyone please tell me their experiences with the Tyan i7501 series (Xeon-basd), or recommend an alternate motherboard? Thanks Scott Scott M. Stingel Emerging Voice Technology Inc.

Hi- I have an upcoming application that requires use of PRI channels that are primarily used for high-volume incoming traffic, but that are to be used for outbound calling as well. Of course, one option is to have dedicated outbound channels reserved, but this is an inefficient use of channel resources. Normally PBX's are designed to have the CPE yield to an incoming call if a particular

Hi all- It's often mentioned here that recompiling the Linux kernel may improve the performance of asterisk. My question is: Does re-compiling the kernel have any effect if there are no changes to the configuration? What parameters will typically improve performance? Thanks for any insight! Scott Scott M. Stingel Emerging Voice Technology Inc. Palo Alto, California and London,

Hello- Has anyone had experience connecting to a Marconi switch (in the UK) using E1-PRI connections (TE410P)? In a new installation, my customer is getting yellow alarms on every channel about every 30 seconds. These alarms clear themselves immediately and then re-occur in another 30 seconds, ad infinitum. I used the same configuration that I've used successfully in the past while talking

Hi- Because a majority of my customers are in Europe, I've gotten quite used to working with ISDN (PRI) and BRI on a regular basis. Recently one of my customers asked me if I could terminate a few lines locally here in the USA (California), so I called up SBC to enquire as to how much it would cost to install a BRI here. Although the rates were reasonable (except the installation), I got

Update on this problem: I gave up on the "native" h.323 because, like others, I couldn't get audio working. (yes, I tried disabling FastStart in ast_h323.cpp - no change) So I went and got the OH323 code from www.inaccessnetworks.com. Glad to say that everything seems to work so far. Not only does audio work, but even the handshaking is now working in both OpenPhone and even

Hi- Anyone using the Junghann's quad BRI card and the Digium E100P in the same system? I'm having a configuration problem where I can configure the cards one at a time (with the appropriate drivers loaded) in a system, but when I try them both together, neither will work. They both work fine one at a time. Probably has something to do with the channel numbering. I've tried

Hi- I've been considering writing some self-test software for several quad-E1 cards that I've just received from Digium. I don't have an E-1 channel bank, so this would be my way of checking that everything hardware-wise is working fine before I head out to the dark and cold confines of my customer's equipment room - to make everything work with their E1's. I was thinking of

Hi all- HELP! This is actually a revisit of a problem that I had earlier with E400P's at a customer site. Customer still gets locked up channel problem, but has learned to live with it (channels clear themselves after several minutes). The symptoms, which I believe are directly related: I'm having problems with tons of framing and "read" errors on my E1 connections (and