similar to: E&M DID config question

I have a Toshiba DK424 connected via T1 E&M to a TE110P card. Intermittently when a user dials a number I am getting 'getdtmf' errors on the Ast server and the calls do not go through. If they dial the number once or twice more, it works fine and I receive no DTMF problems. On another note, end users are complaining about intermittent disconnects. T1 is ESF/B8ZS - 24 chan. Other

HI, I have been pulling my hair out trying to get a Cisco MC3810 to interface my Asterisk box with a T1. I am able to make outgoing calls but incoing calls never reach my Asterisk box. The cisco give a fast busy when I try to call one of the DID's. When playing around with the dial-peers I can get the cisco to pick up the call, but then it forwards the call back to the ANI that is dialing.

Hello, I've got very annoying behaviour from our asterisk PBX. We have 12 channels T1 e&m wink start for TDM and using iax softphones internally (iaxcomm, but tried firefly-thirdparty and discarded for bad sound quality). Slackware 9.1 w/ kernel 2.4.26+ digium TE110P card. In some cases when call is placed from softphone to TDM, system does not detect call answered on Zap channel and

hi, i have some newbie questions about channel banks. i have an adtran act-1241 sitting around. it accepts D4 modules, and it contains a number of e&m cards. first of all, how does this thing work? a t1 contains 24 channels, and i noticed that the channel bank has space for 24 cards. what do these cards do? what are their outputs? the ones that are in there have some outputs on the front

I am setting up a box with a T100P. Everything is going well. The company I am working with has their one phone switch gear. They provisioned me a E&M Wink T1. Cannot do PRI unfortunately. We chose E&M so we could pass an unlimited number of DIDs to the trunk as apposed to FXS loopstart signaling. I can make outbound calls no problem, but I am having problems with the dial plan for inbound

I have a couple of live T1s sitting around and they are not ISDN(like most of the people that are using Asterisk seem to be using), they are regular old 24 channel, robbed-bit, E&M wink start, D4AMI T1 circuits. Can I get these T1s to work with a T100P Digium card and asterisk? Searching through the lists and the documentation I haven't seen any examples of how to configure this kind

Attempting to talk to an Eagle Telephonics switch at a disaster exercise. Didn't think a plain old E&M wink start T1 would be this much of an issue. We finally got the Eagle to accept a call from *, but whilst I can hear the person on the Eagle, they can't hear me. When they initiate a dial out I only get the first 2 digits from their switch... Does anyone have decent

Hi, Can I make e&m wink start lines just wait for digits - instead of going to default? Someone else cleared a similar problem (as described below) on an fxo port with "usecallerid => no" but it is not doing the trick for me. In this case the line when straight to default which would be ok also. John I posted the stuff below about a week ago... I set up a t1 from my sys75 to

When I send a call from my TE410P using E&M, the legacy PBX answers the call but doesn't route it. Any idea what this could be? I assume the digits aren't being delivered properly to the legacy pbx. Any suggestions on what config settings to muck with? Asterisk SVN-branch-1.2-r40901 built by root @ pbx04 on a i686 running Linux on 2007-01-14 14:05:02 UTC zaptel.conf

How do I setup my T1 card as an E&M tie line? Any special configuration? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050523/8aac4dbf/attachment.htm

Hi All, I'm trying to configure a Digium T100P to talk to a legacy voicemail system. I have the signaling specs verbatim from the original manufacturer documentation as follows: [T1 Signaling] Service Type: T1,D4 format, AMI(Super Fram) Signaling: Four wire, terminated, E&M (Robbed bit) Start Protocol: Wink start; 250msec duration Dial Tone: Enabled Digits: DTMF, 4-digits DTMF: 50msec

Maybe of you guys know the answer to this: We have T1's that come from both MCI and Global Crossing as channelized (24 Ports per T) with inband (DTMF) delivery of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail system

Hello, I'm trying to set the 3rd span of a new digium quad card as a E&M T1 for Faxes to a Hylafax server. The 1st and 2nd spans are working as PRIs. When I start asterisk, the logs show a signaling error and chan_zap.c dies. I also get an error that it can't read the gains but they are the standard shown below. 2.6 kernel, Debian Stable, * 1.2 svn from feb 2007 my procedure: make

Maybe of you guys know the answer to this: We have T1's that come from both MCI and Global Crossing as channelized (24 Ports per T) with inband (DTMF) delivery of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail system correctly

I need to create a couple of tie lines between a legacy system and an Asterisk system. I was told that the tie lines are E4 Superframe E&M. I have done E&M wink but have no idea about E4 Superframe E&M and Google is not helping me here. Does anyone know about this type of signaling and if Asterisk can handle it? Thanks, Steve

Hello, I have a T1 (not PRI) plugged into my Asterisk server. Everything is working well, except I only get the first digit of the 4 digit DID in Asterisk. The T1 provider (Eschelon) tried switching to 7 digits, and I only got the first digit of the 7. Can anybody help? We're adding another DID and I need to trap it correctly. Thanks. Here are snippets from the relevant files: --

We're having some difficulty connecting a T1 fax board card to asterisk, with E&M Wink. We've successfully connected it to other E&M Wink T1s, but have been unable to get asterisk to hear it's dialing. Asterisk can dial down to it with no problem, and it hears all the digits, but whenever it sends digits down to asterisk, * always only "gets" the first one. This is

SBC installed a T1 ADTSe (Digital Trunking Service Enhanced) e&m wink start with 24 1 way trunks. The CO says they dial pulse DP the seven digit dnis number. The channels work now but take long time to answer and get these messages repeating until I guess the CO stops Pulse dialing the number. Nov 23 19:08:58 WARNING[1827865]: chan_zap.c:4718 ss_thread: getdtmf on channel 8: Operation now

Maybe one of you can help me with this: We have T1's that come from both MCI and Global Crossing as uses channelized (24 Ports per T) with inband (DTMF) ANI and DNIS delivery (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk Server. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail

I'm a bit confused about how to handle this. I have Asterisk sitting in the middle between a Qwest Long Distance T1 (Voice T1, D4, SF, AMI) and an external voice mail PC using a Dialogic D/240SC-T1 card. The Qwest T1 originally was connected to the Dialogic card directly. The signaling was set to E&M Wink Start because Dialogic used this as its default settings, so it just worked