similar to: CAC ADIT600 / T400 config

I am having trouble getting my T100P and ADIT 600 talking. I have 2 FXO 8 port cards in the ADIT and a T1 controller card. I have a T1 x-over cable connecting two together. Here are copies of the relevant bits of my zaptel.conf and Zapata.conf Zaptel.conf span=1,0,0,esf,b8zs loadzone=us defaultzone=us Zapata.cfg context=default signalling=fxs_ks group=1 channel => 1-24 My

I have an adit 600 with one fxo card connected to a Digium single span T1 card. CallerID, disconnect supervision work perfect, however the users complain that they have some sound quality issues, after testing it I realized that whenever one is in a phone call they get like silence between the sounds coming from the other party, almost like a cell phone, in other words if there is no sound coming

Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much

I just picked up a couple CAC Access Bank 1s loaded with FXS that should be arriving shortly. Does anyone have one that they use with Asterisk? If so, would you be willing to shoot me a note with your current configs? I'm not very familiar with CAC/etc, and it would save me countless hours of muddling through .. :) Any others tips you can give me on these banks would be very

Hello, I have an Adit 600 (3 FXS cards) hooked up to a digium T1 card in my asterisk box. I 'connected' the slots to the a:1 T1 interfaces via the command line. The slots (3 fxs) are configured with 'ls' signaling. I configured the T1 card with the same line settings as the T1 interfaces on the adit and I get green lights on both the T1 card and the T1 interface on the adit (so

Hello I just installed a TE110P in a Dell Poweredge 750 (rackmount), which is connected via crossover T1 cable to a adit 600. Anyway, I've encountered an array of errors, which I believe I have narrowed down to the 22 IRQ misses I encounter on zttool. I've noticed that the te110p and the usb device share an IRQ. Could that be the source of my woes? Would disabling the usb device in the

Looking for someone with a successful experience similar to this; I have a need to cross connect a 3COM NBX PBX PRI interface to asterisk, but over a long distance. We do not need any IP connectivity and the solution requires G.711u audio so there is no benefit to using IP. Has anyone here successfully cross connected any PBX PRI interface expecting NI2 PRI signaling B8ZS/ESF with an

I am experimenting with an asterisk setup in my office. The last bit I have to test is working with analog lines. I have TE411p digium card, with an ISDN line plugged into the first, a channel bank plugged into the second port, and the last two ports empty. I have the following setup in my zaptel.conf: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 span=2,0,0,d4,ami fxsks=25 And in zapata.conf, I

Hello, I was wondering if anyone had any ideas to a problem I am having. I have asterisk installed, and running. All extension phones are analog on FXS ports. The phones call each other and even transmit caller ID information but they DO NOT RING. Here is my setup: T400P Quad span T1 card currently connected to a CAC I w/ 12 channels of FXO for incoming lines and 12 channels of FXS for

Can anyone clue me in about these T400 T1 cards I see advertised? I hear they are Digium Clones. Is there some reason to avoid these? How do they compare to TE410P's for example. Bart

Heh guys, I just received a T400 card, I've been using a T100 for a little while, and it works fine when using a raw channelized T1. I'm relocating my asterisk machine, and PRI's will only be available, haven't found any good config info for PRI's, can someone point me to PRI config info, or let me know what changes I need to make in order to bring them up, I imagine,

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

Has anyone ever heard of this so called Dynamic Impedance matching on the ADIT 600? I called their support and they've never heard of it. We are of course having echo problems are on the far end due to digital/analog conversion on the local end using a channel bank. We have purchased an ADIT 600 and yes the complaints are "far less" however we're still getting them. While I have

I'm having a problem with a new installation of asterisk 1.2.5 with a digium dual port T1 (span 1 connected to an outside line, and span 2 connected to a CAC access bank I channel bank with 24 fxs ports). When I start Asterisk (either from safe_asterisk or asterisk -vvvc) it will immediately exit after it initializes. It will start the logger, register applications and functions, register

My TE411p does not seem to like to have two PRIs from different telcos (span 1 and span 2). I can get one working, but not the other. However, if I use vpmsupport=0 when loading the wct4xxp module, they both work. But here is the problem, vpmsupport=0 disables the on board echo cancellation. Any ideas? BTW, here is zaptel.conf span=1,1,0,esf,b8zs span=2,2,0,esf,b8zs bchan=1-23 dchan=24

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

Out of the blue i started receiving the following error on my PRI line which connects my asterisk server to a Norstar 0x32 key system. The asterisk zaptel.conf file was configure as follows and this config worked for 6 months until friday. Nothing was changed on either system prior to friday. here is teh zaptel.conf span=1,0,0,esf,b8zs bchan=1-23 dchan=24 span=2,0,0,esf,b8zs bchan=25-47 dchan=48

I know this topic has been covered before - I just want to make sure I am understanding this correctly. | ------------------- | | | | T1 | Channel Bank | | ----------| | | | T1 Cross | | | | | | | | ------------------- -------------- | Asterisk | | | |

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

We have install a DS3 with 28 DS1's we have an Adtran MUX breaking out the DS1's, we are trying to setup the system with 2 dchannels for each 4 DS1's. Everything looks fine when modprobe zaptel and wct4xxp and ztcfg -vvvvvv but when I asterisk asterisk it says: Aug 10 16:33:32 ERROR[8954]: chan_zap.c:6750 mkintf: Channel 24 is reserved for D-channel. Aug 10 16:33:32 ERROR[8954]: