similar to: Info - Adit 600 console password reset

Hi All, Im trying to erase the config in a addit that I got off of ebay. I know the only username enabled is root but it doesn't accept any common passwords. I tried the RST switch on the front of the adit described in a earlier posting to the list. Does anyone have any ideas ? Ive looked thru the boot loader menu and cant find any options for erasing the configuration. Any ideas ?

Jon, I actually had some more discussions with Tim on this issue, and it seems that the channel bank would still be a good option to choose for internal purposes. I would not see any other solution than a channel bank to connect many 2wire phones into one asterisk box. I had a talk today with Carrier Access, and it seems that the adit would do us fine. The fxs cards of the adit 600 are

Has anyone had any success using the Adit 600 with the CMG card talking MGCP to asterisk? I want to have a central asterisk server with 10 Adit 600's at various locations providing 24 FXS ports.... Thanks, Isaac

Can anyone help me with the term that SBC uses to refer to disconnect supervision? I have an Adit 600 channel bank which has helped improve the disconnect detection time down to about 8 seconds. This is still causing some issues in particular with call progress enabled in * we are having a few disconnects while calls are in session (about 2 reported in first 5 days of use). I have talked both to

Hi, Anybody out there running Adit600s? I have in my care an Adit600 channel bank connected to an old (version 1.0.6) Asterisk instance with MGCP. When trying a more recent Asterisk (1.4.21.2~dfsg-3+lenny1, Stock current Debian) calls fail. I have attempted to add the "slowsequence = yes" line to mgcp.conf. (It seemed to be the only likely candidate in the example files I found

I have an adit 600 with an fxo card connected to a digium T1 card. If I try to make an outgoing call and the T1 cable is disconnected, asterisks returns congested like it should. But, if the adit 600 is connected to the T1 card, the adit 600 immediately "answers" the call even if there are no physical lines attached. I even removed the fxo card and the adit 600 still

I know a few ppl have those CAC Adit 600's with t400 I can't seem to get my second span up on the T400 connected to the second spand on the adit (A:2) A:1 seems ok Can someone post they zaptel.conf span defintions And maybe a "print config" from the adit 600 cli I think my issue is timing srcs the coding, framing. bld out are all matched thx -------------- next part

Ok, I've pretty much decided to try the Adit route. Somebody who has experience with these tell me if I'm missing something. I have 15 incoming PSTN lines. T1 is not an option at current location. I want to put in an Adit 600 with 2 8-port FXO boards. The adit will then connect to * via a digium t1 board. I configure zaptel.conf for the T1. What other parts would be needed? How do

Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much

Hi, I'm using an Adit 600 Channel Bank with *. I love it and it works really great for my FXS lines. One problem that I have with it (It's really not a problem yet, but it's a potential one) is that I've scoured the manaual for the Adit to see if there's a way to dump out a config file from the bank so in the event of a power and battery failure I don't have to type in the

I've been reading the Google searches trying to understand how to tie together Adit 600 to Asterisk to provide 2 way service. I'm about blind from reading. I assume, the answer is using MGCP between the boxes. However, the examples I found don't really explain fully enough to know how to modify examples to work for me. I'll have in the ADIT with T1's. There is a CMG and

We have an Adit 600 with some fxo lines. Callers calling in on the fxo ports do not hear echo, but the party answering hears bad echo. Here is the gain settings on the Adit: Corporate Adit 600> show 1 SLOT 1: Settings for FXO: Channel 1: Signaling: LSCPD RxGain: -2 dB TxGain: -3 dB And here are the zap settings: busydetect=no callprogress=no

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 It seems like Asterisk are having problems detecting DTMF digits when using an Adit 600 channel bank via MGCP. I've tried to turn on RFC 2833 on both Adit and Asterisk, but no digits at all are working then. Anyone experienced simular with Adit or other channel banks? I'm also unable to use V.90 modem through my setup (Adit600 via MGCP -

Hello All, I'm trying to connect Asterisk to an Executone phone system with an analog DID card and I'm hoping someone can help me figure out what I'm doing wrong. The Executone DID card provides battery to the telco, when the telco wishes to dial a DID it goes off-hook, waits for a wink from the Executone and then dials the last three digits on the number with pulse (as opposed

I've searched but can't find an answer as to how many MGCP paths can a single ADIT/CMG card support? It appears it's only 24 ports, maybe 48. What I'd like to do is install 6 Telco T1's into a single (or more) Adit 600 and route inbound calls towards asterisk. Can I have more than one CMG in a single chassis? Or maybe you know of a better way to connect T1's to

I'm emailing this as the customer in this case, since my carrier appears to be completely unable to solve this. A brief rundown of the problem: - We have several voice lines going through the ADIT, of course into a VoIP type of arrangement. - Voice traffic will become choppy, even drop calls completely, at random but quite often. Modem calls (which we needed unfortunately) are a joke. -

Can anyone help me with the term that SBC uses to refer to disconnect supervision? I have an Adit 600 channel bank which has helped improve the disconnect detection time down to about 8 seconds. This is still causing some issues in particular with call progress on we are having a few disconnects while calls are in session. I have talked both to some local phone contractors and SBC directly and

I am a little confused about the FXO ports on the Carrier Accesss Bank 1. The wiki, and people on the mailing list have stated that they do not have impedance matching, but Carrier Access states in their documentation that they do have impednace matching. Did Carrier Access make a typo, or does it depend on the version of the FXO card? I current have a CAC AB1, and I am having echo problems

Has anyone ever gotten an Adit 600 to work with Asterisk1.4 via MGCP. Asterisk keeps giving me the following error in the LOGs: [Jun 30 08:32:59] NOTICE[26785]: chan_mgcp.c:1726 find_subchannel_and_lock: Gateway 10.0.0.245' (and thus its endpoint '*') does not exist MGCP Config: [AFSWestAdit600] host = dynamic context = default canreinvite = no threewaycalling = yes

Hello, I have an Adit 600 (3 FXS cards) hooked up to a digium T1 card in my asterisk box. I 'connected' the slots to the a:1 T1 interfaces via the command line. The slots (3 fxs) are configured with 'ls' signaling. I configured the T1 card with the same line settings as the T1 interfaces on the adit and I get green lights on both the T1 card and the T1 interface on the adit (so