similar to: TDM cards and Asterisk

HI, I just installed an additional module to a TDM400P card. Everything worked fine for a while, but after rebooting the server the new channel fails to be recognized by asterisk. Here is the output == Parsing '/etc/asterisk/zapata.conf': Found -- Registered channel 1, FXS Kewlstart signalling -- Registered channel 2, FXO Kewlstart signalling -- Registered channel 3, FXO

Hi, I recently purchased two X100Ps and a TMD40B. I have set everything up according to the instructions however I can't get asterisk to pick up an incoming call (It just keeps ringing). Also, when I pick up an internal extension I get dead air. I searched the mailing list for 3+ hours -- What am I missing? Thanks in advance for your help. Here are the installion steps that I used:

I have two grandstream budtetone-100 and cisco 7960g phones. When I talk via speaker phone on either of the phones I get a lot of echo. Any suggestions? Also how do I turn on the mark echo canceller. -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of asterisk-users-request@lists.digium.com Sent: Tuesday, April 13,

Hello I have installed my new E100P card in the same machin with two TDM04B cards. I have followthe instructions on http://www.digium.com/index.php?menu=configuration#T_E100P_PRI This is my zapata.conf span=1,0,0,cas,ami fxsls=1-15,17-31 dchan=16 fxsks=32-39 loadzone = us defaultzone=us I do *modprobe zaptel wct1xxp wcfxs ans seems to work ok. * But when i do ztcfg -vvv i got Zaptel

Hi I have been searching the wiki and mailing lists and I cant see where my config is incorrect. I have a Digium tdm11b (1 fxo + 1 fxs) this is the output of cat /etc/zaptel.conf # Autogenerated by /usr/local/sbin/genzaptelconf -- do not hand edit # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # It must be in the module loading order # Span 1: WCTDM/0

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

I think I have a bad FXS module on my TDM400P. Channel map: >> >> Channel 01: FXO Kewlstart (Default) (Slaves: 01) >> Channel 02: FXS Kewlstart (Default) (Slaves: 02) >> >> 2 channels configured. >> ZT_CHANCONFIG failed on channel 1: No such device or address (6) The zaptel loads ok, but the wctdm reports No such device or address and stays loaded. The

Is there anything special needed to load up a TDM10B card?? I got the card today.. Took it from the box, put it into a PCI slot.. connected the power to the card and booted the PC.. I have removed the X100P to avoid confusion and I have the following in the config files.. in /etc/zaptel.conf # For the X100P #fxsks=1 # For the TDM10B fxoks=1 in /etc/asterisk/zapata.conf [channels]

(I'm producing a writeup on all the things one run into building an * box. Which after a couple of boxes is showing up aplenty.) So this uses the working h/w and config's from another box. All I do is build in a new computer. Loading the modules I got: __________________________________________________ Zaptel Configuration ====================== Channel map: Channel 01: FXS

Hi list. I'm having the next problem. I have a * with 1 TDM400P (4 ports) and one X100P, with a working configuration. Today i add one more X100P card, and i change the config files as next: zapatel.conf: fxsks=1-2 fxoks=3-6 loadzone = us defaultzone=us zapata.conf ... context=bell

>rom: "Jose Hernandez" <jfhernandez_01@verizon.net> >Subject: RE: [Asterisk-Users] Unable to open master device > '/dev/zap/ctl' > >If you are using udev you will get a message during compile suggesting to >read README.udev, I did not pay attention to this message. > >Anyways.. I did not get the error after creating a udev rules file in

Hi, I have a very newbie question, I asked this at the digium support, but they did not answered yet, so I hope you can help. I just bought the digium developer kit (TDM400P), installed everything, all messages seems ok, but I can't make it work. * a normal telephone and a line connected to the board * modprobe wcfxs = ok leds go on an I hear a small click at the phone. * ztcfg = ok

Hi, I just got my TDM400P card (2 modules) and i installed it no probs. The card is detected fine, but for some reason when I add the card to zaptel.conf i get the following error: --snip-- ZT_CHANCONFIG failed on channel 2: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? --snip-- My /etc/zaptel.conf looks

I'm trying to figure out how to start *..... Rh7.3,CVS,TE410P,TA750 If I just try the way the docs spell it out "/usr/sbin/asterisk -vvvc" it fails...... /var/log/asterisk/messages Oct 3 22:23:34 WARNING[1024]: File chan_zap.c, Line 610 (zt_open): Unable to open '/dev/zap/channel': No such device Oct 3 22:23:34 ERROR[1024]: File chan_zap.c, Line 4930 (mkintf): Unable

I'm having trouble getting the cards configured. I have followed the instructions but get errors. when I modprobe zaptel /lib/modules/2.4.21-0.13mdk/misc/zaptel.o: unresolved symbol proc_mkdir_Re6122de7 /lib/modules/2.4.21-0.13mdk/misc/zaptel.o: unresolved symbol skb_over_panic_R5ced0794 /lib/modules/2.4.21-0.13mdk/misc/zaptel.o: unresolved symbol devfs_generate_path_R4c75cb0f

(Sorry of this appears in the list twice, but I wasn't sure if it was blocked or not) Hi there, I'm having a problem with my TDM-400P which has been working like a charm up until very recently. It started to fail last week, and so I was hoping someone could illuminate me with some information as to why. Its configuration is as follows: ------------ FXS (green) module is in position 1,

Hi: I'm using a TDM-400 to terminate PSTN lines at my Asterisk server with kewlstart signalling. When an outside caller calls the server, the TDM-400 goes off-hook and provides a ringing tone to the caller. If the caller hangs up before the receiving party answers the phone, Asterisk fails to detect the hang-up. The TDM-400 stays off-hook, hogging the line, while Asterisk rings the

I've searched the site with google, but can't think of the magic words I guess. I got a "swap out" TDM30 today to replace my buzzy one. I swapped it with the older one, swapped out the FXS modules, hooked it up to the computer's power supply, and booted, but the wcfxs driver won't load--it gives me the standard "Cannot init module" types of errors that

Hi all, I'm trying to get a junghanns QuadBRI to coexist in the same machine as a Digium TDM400P card (so I can run the ISDN lines in and bridge with analog phones plugged into the TDM). I'm having a problem loading the modules. If I follow the BRIstuff (0.3.0-pre-1l) install method.... it's to modprobe zaptel, then insmod qozap.o I'm on Debian 2.4.31. That works. But then I