similar to: Diva 4BRI, asterisk and capidrv support ?

Hi, I am trying to configure a Diva Server 4BRI to work with chan_capi. Here are the steps that I took: - compiled fresh kernel with new-style CAPI support: i4l_divas_1.2 - got the divactrl_1.2 utilities, configured the card startup scripts, - rebooted, card firmware loaded properly, "capiinfo" displays detailed info on 4 controllers, however there is an error message: FAC REQ -

I own a ME600 EPIA Mini-ITX main board with the latest Debian distro (kernel 2.6.8) with isdnutils-base, libcapi20-dev, libcapi20-2, isdnactivecards installed. I have a QuadBRI module by Junghanns with bristuff-0.2.0-RC3a (with asterisk-1.0.3, zaptel-1.0.3 and libpri-1.0.3), and chan_capi-0.3.5. I followed all INSTALL instructions, but I have some strange behaviour. All modules seems to be

Hi, i will use an AVM C2 controller with asterisk. How can i use both card ports ?? On the voip-info.org Wiki is only notice to: You will need a section for each controller in /etc/asterisk/capi.conf so the C2 will have 2 sections. But how is look like this ? Only on the first port is asterisk assume connections, but nothing on the second card port. In the dmesg is only the capidrv-1 shown,

Hi all, * was running ... I have a WT405P and an AVM C4 with chan_capi 0.3.4a Today chan_capi stopped working, without any changings at the system. It seems, that not * is the reason, because isdn-log also shows no calls. If I try to call * from outside via capi, I only get a busy. That is the try from inside to outside: stern01*CLI> -- data = @89930:0107901723168212 -- capi

Hi all, does anyone have capiECT working? I can't get it to work - please see my logfiles below. While using an * CVS version of late September and chan_capi-0.2.5 (I guess), it worked!!! (I know, never change a running system ... should've backuped ... etc.) Here's the setup: NT----AgfeoISDNPBX----AgfeoISDNPBX----AnalogPhones in between the two PBX I attached my * server with a

Hi *, This is my first message to this list, so I hope I am not breaking any rule with my post. My question is the following: can I establish a voice connection over an ISDN interface by using a bluetooth dongle to connect to the ISDN access point? Here follow the details: I have compiled and configured asterisk. Everything seems fine except that when I configure asterisk to use the ISDN

Suddenly after recompiling my 2.4.22 kernel I can no longer load chan_zap: Sep 22 21:25:08 ERROR[16384]: File chan_zap.c, Line 5145 (mkintf): Unable to get span status: Inappropriate ioctl for device Sep 22 21:25:08 ERROR[16384]: File chan_zap.c, Line 6638 (load_module): Unable to register channel '1' Sep 22 21:25:08 WARNING[16384]: File loader.c, Line 301 (ast_load_resource):

Hi, Since I use "/usr/sbin/dovecot --exec-mail imap" from mutt I get a lot of these in my syslog: Apr 3 11:09:33 zenon IMAP(ldm): : Connection closed bytes=36/256 Is it possible to suppress them while keeping the "remote users" messages: Apr 3 10:52:05 zenon dovecot: IMAP(xxxxx): Connection closed bytes=9420/5976987 Apr 3 10:52:08 zenon dovecot: imap-login: Login:

I have an asterisk installation connected to 2 isdn lines via an AVM C2 card. modules seems to load well, lsmod gives : c4 19588 4 b1 24192 1 c4 capidrv 28468 2 isdn 134604 9 capidrv slhc 7552 1 isdn capi 18112 4 capifs 6024 2 capi kernelcapi 46112 4

Hi there. http://defan.zenon.net/freebsd/patch-icecast2-encoding This patch allows icecast to encode metadata from specified charset to UTF-8 for stats output and using different charset for log output. Variables to add to config (for example): <icecast> <metadataenc>CP1251</metadataenc> ... <logging> ... <logenc>KOI8-R</logenc> ...

Processing commands for control at bugs.debian.org: > found 661231 1:3.22+dfsg1-2 Bug #661231 [isdnlog] isdnlog: unowned files after purge (policy 6.8) violating FHS (policy 9.1) too Bug #331116 [isdnlog] isdnlog: fails to purge Marked as found in versions isdnutils/1:3.22+dfsg1-2. Marked as found in versions isdnutils/1:3.22+dfsg1-2. > found 527067 1.4.15+nmu2 Bug #527067

Hello, Can I add multiple mails in Samba4 ? I wan't auth user via mail but user have mailbox with multiple domain. I want have one acount one user multiple mailbox. Is posible to do that ? -- Z poważaniem / Yours sincerely Zenon Matuszyk mobile: 00 48 797 004 938 e-mail: zenon.matuszyk at networkers.pl www: http://www.networkers.pl

Hello all, I just got the latest cvs snapshot and I'm trying to compile asterisk.. When I run nefeli:/usr/src/asterisk/zaptel# make clean; make linux26 Compile stops with errors... /usr/src/asterisk/zaptel/zaptel.c:6509: warning: passing argument 2 of 'class_device_create' makes pointer from integer without a cast /usr/src/asterisk/zaptel/zaptel.c:6509: warning: passing argument 3

I'm using avm fritz card usb with kernel 2.6 patch with mISDN. The module is load correctly when I type lsmod I've got the following output: Module Size Used by zaptel 178308 0 avmfritz 21388 0 mISDN_isac 14336 1 avmfritz mISDN_dsp 191424 0 l3udss1 34184 0 mISDN_l2 39040 0

Hi Zenon, It seems likely to me that you still have libshout 1.x installed. Try stripping all remnants of libshout out from /usr/(local/)include and /usr/(local/)lib and then (re)install libshout 2.0, downloadable from http://downloads.us.xiph.org/releases/libshout/libshout-2.0.tar.gz (NB: this in turn requires libogg and libvorbis.) -- J. Zenon Panoussis wrote: > > Hi > >

i'd be happy with any solution. XML listings of streams often have parse errors due to non UTF-8 characters in the metadata. (My own quick and dirty fix was for XSL to generate plain-text output..) --mark On Mon, 23 Oct 2006 17:34:36 +0200, Michael Smith wrote: > On 10/23/06, Andrew N. Below <defan@zenon.net> wrote: > >Hi there. > > >

Hello, Since changing to "passdb backend = ldapsam" on my debian unstable PDC things work well, however a new winxp machine can't join the domain. Here is the /var/log/samba/log.smbd output. It seems the sticking point is about a missing user RID? (the new machine is sylla). Thanks in advance for any hints as to what may be wrong, cheer, 2002/10/08 18:06:30, 0]

I have a Dell PowerEdge 4300 server with dual Zenon 550 MHz processors, SCSI controller with four 9MB drives and 1 GB of RAM. I want to develop an asterisk pbx with 4 POTS lines in and 16 analog extensions (no VOIP). I also will install a sound card for an intercom. Is this hardware sufficient if using a Digium TDM2400P? -- Thanks, David Little M&M Technology, Inc. david at

Hi Zenon, First step would be to ensure that all clients are connected to all bricks - this will reduce the chance of new problems. For some reason there are problems with the broken node. Did you reduce the replica to 2 before reinstalling the broken node and re-adding it to the TSP ? Try to get the attributes and the blames of a few files.The following article (check all 3 parts) could help you

Zenon Panoussis wrote: > > Dan Stowell wrote: > > [icecast can't write to log files] > > > running it as myself ("dan") - the same as the owner of the logfiles > > and of the containing folder. > > >> > -rw-rw-r-- 1 dan admin 0 6 Dec 23:48 icecast2access.log > >> > -rw-rw-r-- 1 dan admin 0 6 Dec 23:48