Displaying 20 results from an estimated 10000 matches similar to: "Re: two computers set up ... now what?"
2003 Apr 28
9
Dialing using X100P
My setup:
X100P and Quicknet PhoneJack.
I can't seem to properly set up a Zap channel for my X100P.
Here are some of my configurations:
[zaptel.conf]
fxsks=1 #X100P
fxoks=2 #Quicknet PhoneJack
defaultzone=us
loadzone=us
[zapata.conf]
[channels]
context=local
signalling=fxs_ks
channel->1 ;X100P
[extensions.conf]
...
[local]
exten=>_NXXNXXXXXX,1,Dial,Zap/1
;I'm pretty sure the
2003 May 20
3
Need help with zapata.conf
I'm having a problem defining my channels
Here is my zapata.conf
-----------------------------------------------------------------------------------------------------
; Zapata telephony interface
;
; Configuration file
[channels]
;
rxwink=300 ; Atlas seems to use long (250ms) winks
usecallerid=yes
hidecallerid=no
callwaiting=yes
callwaitingcallerid=yes
threewaycalling=yes
2004 Jun 09
1
Hang-up Supervision (UK)
Hi everyone,
I've just got my X100P card installed and working but there seems to be an
issue with hang-up supervision.
If I stuff a call out over the X100P card onto the PSTN that's fine. When I
hang up the SIP phone the PSTN call ends. If I receive a call from the
PSTN, it's answered and everything is ok until the remote party hangs up.
Asterisk thinks the call is still active and
2003 Aug 07
2
Newbie Issue
Hi All,
I recently purchased the Asterisk Developer's Kit (TDM) to try out
Asterisk. After following the directions in the Digium's FAQ topic entitled
"Q. How do I configure my TDM40B and X100P?", I'm receiving the following
error:
WARNING[1074428608]: File chan_zap.c, Line 6748 (load_module): Ignoring
rxwink
ERROR[1074428608]: File chan_zap.c, Line 6692 (load_module):
2005 Jul 03
1
TDM01B card configuration
Hello,
I am trying the setup the TDM01B card. 1 FXO. I
connected it to a regular home line. in the
/etc/zaptel.conf, I have
fxsls=4
In the /etc/asterisk/zapata.conf
I have:
signaling=fxs_ls
language=en
group=1
context=default
channel => 4
When I start asterisk, I get this error:
ERROR[10376]: chan_zap.c:6584 mkintf; Signaling
requested on channel 4 is FXO Loopstart but line is in
FXS
2009 Apr 11
1
asterisknow 1.5 with X100P and TDM400P
Hi All,
Sorry if this has been around a millions times.. I have been off this
list for a few months now..
I have installed the latest asterisknow (upgraded asterisk to 1.6 as
well) and I am having a hard time getting my X100P and TDM400P working..
Its all new to me with dahdi because my old server is still running
Asterisk 1.0.2 so there have been lost of changes..
Can someone point me in
2006 Mar 27
2
FXO without answer supervision
Simple question that google hasn't helped much with (likely poor search
terms)
I just installed a Sangoma A200 with overall good results. Initial
tests with both
incoming and outgoing calls were very positive. Until I made a normal
call that
lasted more than 30 seconds.
I setup the FXO with kewlstart signalling, and the outgoing call is
never registered
as 'Answered' and the dial
2004 Jan 30
9
Adtran 750 DID question.
Hello All,
I've mostly solved my DID problem from a few days ago. Apparenly the lines weren't configured properly. Now heres the next question. 12 E&M wink lines from telco. I have them all plugging into an Adtran 750 with FXS cards. The Adtran ports are configured DPO. How do I signal this from Zaptel. I have them setup E&M in zaptel.conf and EM_W in zapata.conf. They
2003 Oct 01
1
Audiocodes gateway and asterisk
Is anyone on the list using an Audiocodes gateway with asterisk and SIP?
I'm looking at that platform, but I have a couple of issues:
1) Echo cancellation. The echo that I'm hearing with an X100P is
unacceptable. Does the Audiocodes do better?
2) Line signalling. I'm using Kewlstart with the X100P, but it looks like
the audiocodes uses loopstart only. How does this work with
2003 Dec 04
2
x100p/hangup detection issues?
Hi..
I've got an asterisk setup with an X100P card installed.. I'm noticing that upon hangup, it takes a good 3 to 5 seconds before asterisk realizes the line has been hung up and drops the call.. this causes my SIP phone to continue ringing, and occassional phantom voice mail messages to be left.. I'm located in good old standard North America, with a regular Verizon residential
2003 May 01
6
No Dialtone
So I have an X100P, and a TDM10B both working (at least I think they are).
The drivers have been loaded and ztcfg -vv shows no errors in the
configuration of two channels.
When I run asterisk -vvvc and pick up my phone (plugged into TDM10B), I
don't gear a dialtone.
in phone.conf, I have
[interfaces]
mode=dialtone
format=slinear
...
Shouldn't that produce a dialtone when I pick up the
2008 Apr 14
4
Unable to load module chan_zap.so
I am having trouble with chan_zap.so not loading. When I load it from
modules.conf, Asterisk bails out without any error message. When I
load it from the console, it just says "Unable to load module
chan_zap.so" no matter what verbose level I am using.
dmesg says:
Zaptel Version: 1.4.4
Zaptel Echo Canceller: MG2
Freshmaker version: 73
Freshmaker passed register test
Module 0:
2007 Jul 20
2
Problem
i am have x100P clone, and install asterisk 1.4 and out call normaly and
hangup in xlite to zap but call to asterisk for zap channel nop pass to
xlite and the caller hangup the asterisk not detect.
what is the problem ???
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070720/39d4c1e8/attachment.htm
2004 Sep 11
1
Final status of the call
Hello to all:
When I make a call of extension (FXS) to extension (FXS) (TDM40B) status of the
call is the following one:
#### Case call answered
--------------------------------------------------- Log init
-- Starting simple switch on 'Zap/4-1'
-- Executing Macro("Zap/4-1", "stdexten|103|Zap/2") in new stack
-- Executing Dial("Zap/4-1",
2007 Apr 30
1
TDM400P and Junghanns QuadBRI issue
Hi List,
I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI
on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6).
I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4
and asterisk-1.2.17
When it's the time for ztcfg to do its job it complains with
<ZT_SPANCONFIG failed on span 2: No such device or address (6)>
2004 Nov 21
3
TDM400 FXO stops handling outgoing calls, but still accepts incoming?
I have a bit of a weird problem that I'm having great trouble debugging.
I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules
are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID,
which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS.
Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls.
My
2003 Dec 04
2
Carrier Access Channel Bank Setup -- No hangup
I just purchased a T100p from digium and a Carrier Access Access Bank 1 channel
bank (12fxs/12fxo). I have the setup partially working thanks to some help from
IRC. However I still have the following issues I can't seem to resolve
1. When calling into the system from the PSTN call hangup is not detected. *
leaves line in use until it is shutdown.
2. When calling an analog phone connected to
2004 Nov 26
1
Which is the best signalling for FXS
Hi All,
Which is the best signalling to use when connecting an FXS inteface on a
TDM400 to a standard telephone. I see that all examples use fxo_ks, but it
is my understanding that kewl start is really designed for connections to
the CO so that hangup etc. can be detected. So does it make any sense to
configure a telephone for fxo_ks? Or should it be configured for fxo_ls?
Regards
Garry Taylor
2003 Apr 30
9
TDM10B problem
Ok. I just got a TDM10B and it is in with my X100P. So as it says in the
provided instructions, I used the command
modprobe tor2
I get an error message saying that there is no such device.
My zaptel.conf looks like this:
fxsks=1
fxoks=2
So I load the X100P first. (modprobe wcfxo)
Then I load the TDM10B (modprobe tor2)
Then I'm told that the device doesn't exist.
Please help
2003 Jun 20
1
Question :: groundstart and loopstart :: Update
Callerid issue
1) if you run ztmonitor on the fxo line & call in do you hear the fsk tone
if yes then we beleive the CAC is passing fsk
2) in chan_zap->ss_thread around line 4154 (current cvs)
if you get to the callerid_feed at least once then
if you get to chan_zap->ss_thread->callerid_get around line 4163 (current cvs)
does this parse fail