search for: zttools

Hi, I installed s fresh system yesterday and it seems that zttool did not install!! ztcfg is there.. Anyone else had this problem or is it just me? -- ______________________________________________ http://www.linuxmail.org/ Now with e-mail forwarding for only US$5.95/yr Powered by Outblaze

New to list, going through steep learning curve with *, could someone assist with how to install zttool with slackware10, the normal make zttool fails, assume I am missing a dependency? (newt and newt-devel?) Trying to test Q.031 pri span with TE405p card, Google has little clue on Zttool and the * manual has a heading, but no entry? Thanks Magnus

It appears that zttool doesn't actually report T1 span errors. If I inject BPV's, crc errors, framing errors, etc into a T1 span, the counters on zttool don't change.

SYNOPSIS Erratic red alarm T1 PRI on asterisk, but zttool running concurrently during alarm shows no errors, irq misses, or alarms, on any span. Using asterisk and quad Digium T405P, configured as follows: Span 1 connects to ISDN PRI (fractional 8 B channels, D channel 24). Span 2 connects to T1 Mux and analog stations. Span 3 connects to ISDN PRI Nortel BCM hybrid key system digital trunk.

Just noticed that no matter what the line condition is, zttool always reports "OK", so it's pretty useless. (In contrast, I'd get "Red alert" if I unplug the line connecting to an X100P.) I'm using zaptel 1.2.15 on Linux 2.6.15-28 (also tested on 2.6.10). Yuan Liu

I am trying to compile zapata under a 2.6 kernel (Suse 9.1 all patches installed). I am getting the error bellow: Any ideas? Anybody able to successfully compile this in Suse 9.1? 500@suse91lx:~/dl/pbx/zaptel-1.0-RC2> make linux26 cc -I. -O4 -g -Wall -DBUILDING_TONEZONE -DSTANDALONE_ZAPATA -c -o zttool.o zttool.c cc -o zttool zttool.o -lnewt make -C /usr/src/linux-2.6

Hi, Using Xorcom's bristuff-0.4.0-RC4-xr7.tar.gz (ie asterisk 1.4.25) with an old Junghanns OctoBRI (ie not the 2.0 version), zttool shows every port in TE mode, though half of them are in NT. Alarm column shows OK for every port, such as : OK octoBRI PCI ISDN Card 1 Span 1 [TE] Lay Globally, this system doesn't work (can't dial out through zaptel) Replacing this board

I wouldn't normally post this to the asterisk mailing list but I'm really stuck... I've been trying to get meetme working on and off for a few months now but I always hit a brick wall when trying to compile. I keep seeing this... make linux26 cc -I. -O4 -g -Wall -DBUILDING_TONEZONE -DSTANDALONE_ZAPATA -DZAPTEL_CONFIG=\"/etc/zaptel.conf\" -c -o gendigits.o

Hello all, Does anyone know where I can get an explanation of how to use zttool? I am running a PRI between to asterisk servers for testing and on one end of the PRI (the pri_cpe side), I see Tx/Rx Levels: 0/ 3 On all other PRIs, I see 0/0. Can anyone tell me what this means? The real problem is that I get HDLC Abort errors every couple of minutes on this PRI and I am trying to figure

Can anyone with a TE405P tell me what zttool tells them the type of card installed. With ours it says it's a TE410P. B

I have a TDM800 that is installed and working. (TDM800 + 2 X QUAD FXO). Zttool says it is configured, ok, and there are no issues. Ztcfg -vvv shows that all the channels are configured. Zap show channels in the CLI show all 8 channels configured as they are supposed to be. When I plug in a pots line from the telco and make a call to that line, asterisk does not respond. (No Starting

Hi List, After reading a bunch of the docs, list post archives, it still seems that a clear definition of how to clock the T100P card is muddy. zttool says that the link is "INTERNALLY CLOCKED", does this mean the T100P is providing clock, or does this mean the T100P is getting clock from the T1 line side (ergo getting clock from the Telco) ?? If you have sync = 0 then zttool

Hello, I have an E100P, and in the zaptel.conf I have: span=1,1,0,ccs,hdb4,crc4,yellow fxsks=1-10 the light on the card is green( BTW what do all those states of the card that zttool reports YELLO, RED, BLUE ..., is there a doc for zttool?, or for the card?) in the asterisks` zapata.conf I have: [channels] context=default switchtype=euroisdn signalling=fxs_ks usecallerid=yes hidecallerid=no

To recap: T100P card wouldn't sync with the telco using line side clocking ( span=1,1,0.........) Had to use internal clocking (span=1,0,0.......) zttool showed Tx/Rx Levels as 0/ 1 For the grins of it I replaced the T100P card with another newer card from inventory. This newer card has the same rev on the ASIC / FPGA but doesn't have any of the various jumper headers installed

Hi list, We have been trying to configure a Quad Span T1 card in a system running RH9. We have followed the instructions in the Wiki and searched the mailing lists, but so far havent got any success. Cable is connected to the first span, and module is loaded. Without loading the module the LED glows in red colour, but the moment we load module, it goes off. (No red or green) . We ran zttool

Group Having trouble installing zaptel. Below is my server specs Intel Motherboard D101GGC TE405P CentOS-4.2-i386 Here is the output trying to do a 'make' =============================================== make clean rm -f torisatool makefw tor2fw.h radfw.h rm -f ztcfg torisatool makefw ztmonitor ztspeed zttool zttest fxotune rm -f *.o ztcfg tzdriver sethdlc sethdlc-new rm -f

In my * server I have a T100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm on the card starts blinking red. Running zttool confirmed that yes, it is a red alarm. I've read a few previous posts on this type of setup and I'm not too much closer. What should I be checking next? A different cable? The

Hello I have contacted my line provider who is saying that in order to get my 0845 or 0870 number to id as the incoming number on a landline that i may call i need the following. User must provide - NPI set to E.163/E.164 User must provide - TON = "national or international I have had a good search around and can't seem to find a good answer to this. Does anyone have any idea where i

Hi, I have the SuSe9.2 installed in a box with a QuadBri. I have followed all the instructions i have found and this is my best result... only one error compiling zaptel :( .. y have the kernel sources an already made the links to its drwxr-xr-x 8 root root 328 Jun 16 20:20 . drwxr-xr-x 12 root root 320 Jun 16 14:05 .. drwxr-xr-x 3 root root 136 Jun 16 20:17 asterisk drwxr-xr-x 22 root

Chuck, Thank You I'm also going to try CentOS 3 The problem is I have SATA HDD and running in to trouble getting Linux installed. Will update after I test Ver 3 -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Chuck Bunn Sent: Monday, March 13, 2006 12:45 PM To: Asterisk Users Mailing List -