Displaying 20 results from an estimated 23 matches for "wct2xxp".
Did you mean:
wct1xxp
2007 Jun 21
1
Zaptel wct2xxp driver causes LEDs to go black and RED alarm
...ed by a E1 cable to Port 1 on each. On startup, both cards flash
red, alternating between ports 1 and 2.
When server #1 loads the Zaptel module and drivers, Port 1 status LED
goes green. When server #2 loads the same module and drivers, Port 1
status LED goes completely blank. Unloading the wct2xxp module causes
the flashing red LEDs to come back.
I've tried swapping cable ends and cards between the two machines, but
the problem LED always stays with server #2. So, I think there is
something misconfigured with server #2, but the configuration file on
both servers is identical.
zapt...
2007 May 18
2
TE212P octastic initialization failure
...0 IO-APIC-level uhci_hcd:usb2
185: 0 0 IO-APIC-level uhci_hcd:usb3
193: 19 0 IO-APIC-level ehci_hcd:usb4
201: 2148 0 IO-APIC-level ioc0
217: 1153 0 IO-APIC-level eth1
225: 160247 0 IO-APIC-level wct2xxp
NMI: 64 42
LOC: 42340 42317
ERR: 0
MIS: 0
# dmesg
[...]
Found TE2XXP at base address fe7ffc00, remapped to ffffc20000004c00
TE2XXP version c01a016a, burst OFF, slip debug: OFF
Octasic optimized!
FALC version: 00000005, Board ID: 00
Reg 0: 0x7daa5400
Reg...
2006 Jan 08
2
Zaptel make install error
...cho "install $x /sbin/modprobe --ignore-install $x && /sbin/ztcfg" >> ; else echo "post-install $x /sbin/ztcfg" >> ; fi; fi; fi; fi; done; if ! grep "ias wcfxs" ; then echo "alias wcfxs wctdm" >> ; fi; if ! grep "alias wct2xxp" ; then echo "alias wct2xxp wct4xxp" >> ; fi; fi'
make: *** [install] Error 2
----
Mike Hammett
Intelligent Computing Solutions
http://www.ics-il.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/aste...
2011 Feb 21
1
T1 PRI shows yellow/red alarm
.../var/log/asterisk/messages reports:
[Feb 21 12:21:56] NOTICE[4795] chan_dahdi.c: PRI got event: Alarm (4)
on Primary D-channel of span 2
[Feb 21 12:21:56] DEBUG[4795] chan_dahdi.c: Got event Alarm (4) on
D-channel for span 2
/var/log/syslog reports:
Feb 21 12:21:56 asterisk kernel: [509981.796536] wct2xxp: Setting
yellow alarm on span 2
Feb 21 12:21:56 asterisk kernel: [509981.796562] timing source auto card 0!
Feb 21 12:21:56 asterisk kernel: [509981.813535] timing source auto card 0!
Feb 21 12:22:01 asterisk kernel: [509986.813869] wct2xxp: Clearing
yellow alarm on span 2
Intensive PRI debugging...
2008 Apr 14
8
zaptel 1.4.10 regression with TE220B on Proliant DL380 G5 ?
...=56-70,72-86
dchan=71
Under zaptel 1.4.10, when ztcfg runs this gets logged in the kernel
buffer:
About to enter spanconfig!
Done with spanconfig!
About to enter spanconfig!
Done with spanconfig!
About to enter startup!
TE2XXP: Span 1 configured for CCS/HDB3/CRC4
timing source auto card 0!
wct2xxp: Setting yellow alarm on span 1
timing source auto card 0!
SPAN 1: Primary Sync Source
VPM400: Not Present
VPM450: echo cancellation for 64 channels
BUG: soft lockup detected on CPU#0!
[<c044d448>] softlockup_tick+0x96/0xa4
[<c042ddc8>] update_process_times+0x39/0x5c
[<c04196f7>...
2005 Sep 07
1
ztcfg Kills My Dial Tone
...7)
Channel 48: FXO Kewlstart (Default) (Slaves: 48)
48 channels configured.
*** Here are the kernel messages emitted when I run ztcfg -vvv: ***
Sep 7 11:46:22 localhost kernel: About to enter spanconfig!
Sep 7 11:46:22 localhost kernel: About to enter startup!
Sep 7 11:46:22 localhost kernel: wct2xxp: Setting yellow alarm on span 1
Sep 7 11:46:22 localhost kernel: Zaptel: Master changed to TE2/0/2
Sep 7 11:46:22 localhost kernel: TE2XXP: Span 1 configured for ESF/B8ZS
Sep 7 11:46:22 localhost kernel: Putting 0 in register 2f on span 1
Sep 7 11:46:22 localhost kernel: Putting 0 in register 3...
2006 Feb 11
2
configure TE205P on asterisk@home
hi
i'm trying to configure a TE205P on asterisk@home
i've edited /etc/sysconfig/zaptel adding this line:
MODULES="$MODULES wct2xxp"
now, when the system is loading, i can see that the wct2xxp module is
loaded correctly
but if i try the command:
/usr/local/sbin/genzaptelconf
i get:
STOPPING ASTERISK
STOPPING FOP SERVER
Generating '/etc/zaptel.conf'
Generating '/etc/asterisk/zapata-auto.conf'
STOPP...
2006 Jan 19
1
Problems with Module
Hello,
I am installing a TE210P card, but i can't find the wct2xxp module, can
somebody help me to configure my card?
Thanks
Manuel
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060119/1e3af3fb/attachment.htm
2006 Apr 24
1
compiling zaptel-1.2.5
Hello,
What's wrong ?
make install
.....
options torisa base=0xd0000
alias char-major-196 torisa
alias wcfxs wctdm
alias wct2xxp wct4xxp
if [ -d /etc/modutils ]; then \
/sbin/update-modules ; \
fi
depmod: *** Unresolved symbols in
/lib/modules/2.4.27-2-386/misc/wctdm24xxp.o
depmod: *** Unresolved symbols in
/lib/modules/2.4.27-2-386/misc/zaptel.o
depmod: *** Unresolved symbols in
/lib/modules/2.4.27-2-386/misc/ztd-et...
2007 Feb 21
3
Zaptel 1.4.0
...11xp && /sbin/ztcfg
install pciradio /sbin/modprobe --ignore-install pciradio && /sbin/ztcfg
install ztd-loc /sbin/modprobe --ignore-install ztd-loc && /sbin/ztcfg
install ztdummy /sbin/modprobe --ignore-install ztdummy && /sbin/ztcfg
alias wcfxs wctdm
alias wct2xxp wct4xxp
install zttranscode /sbin/modprobe --ignore-install zttranscode &&
/sbin/ztcfg
install wct4xxp /sbin/modprobe --ignore-install wct4xxp && /sbin/ztcfg
However:
[root@Aiur zaptel-1.4.0]# modprobe zaptel
FATAL: Module zaptel not found.
/var/log/dmesg doesn'...
2010 Sep 30
1
channel.c: Got a FRAME_CONTROL (8) frame on channel DAHDI
...0x00000000
wct4xxp 0000:02:00.0: Reg 4: 0x00000000
wct4xxp 0000:02:00.0: Reg 5: 0xd0100014
wct4xxp 0000:02:00.0: Reg 6: 0xc01a0000
wct4xxp 0000:02:00.0: Reg 7: 0x00001f00
wct4xxp 0000:02:00.0: Reg 8: 0x00000000
wct4xxp 0000:02:00.0: Reg 9: 0x00000000
wct4xxp 0000:02:00.0: Reg 10: 0xd0100028
IRQ 16/wct2xxp: IRQF_DISABLED is not guaranteed on shared IRQs
wct4xxp 0000:02:00.0: Found a Wildcard: Wildcard TE210P
dahdi_hardware:
pci:0000:02:00.0 wct4xxp+ d161:0210 Wildcard TE210P
As I think, it's really Digium TE210P. But I don't think, it's a pci
card problem because call drops ex...
2014 Jan 09
2
How to read IRQs and timing slips values
...0 0
0 0 0 IO-APIC-edge ata_piix
15: 0 0 0 0 0
0 0 0 IO-APIC-edge ata_piix
16: 3378646209 3378695076 3378691115 3378697362 3378691116 3378706831
3378710635 3378702358 IO-APIC-fasteoi wct2xxp
Can I positively conclude that my Dahdi PRI board IS NOT sharing IRQ (which
is good) ?
2. What would you suggest reading the following output ?
cat /proc/dahdi/2
Span 2: TE2/0/2 "T2XXP (PCI) Card 0 Span 2" (MASTER) HDB3/CCS
Timing slips: 175319
32 TE2/0/2/1 Clear (In use) (E...
2009 Oct 20
2
Kernel panic w/ DAHDI 2.x/Digium TE220B
...panconfig!
Oct 20 15:20:55 redbox-ast16 kernel: dahdi: Registered tone zone 0
(United States / North America)
Oct 20 15:20:55 redbox-ast16 kernel: About to enter startup!
Oct 20 15:20:55 redbox-ast16 kernel: TE2XXP: Span 1 configured for
ESF/B8ZS
Oct 20 15:20:55 redbox-ast16 kernel: wct2xxp: Setting yellow alarm
on span 1
Oct 20 15:20:55 redbox-ast16 kernel: timing source auto card 0!
Oct 20 15:20:55 redbox-ast16 kernel: SPAN 1: Primary Sync Source
Oct 20 15:20:55 redbox-ast16 kernel: VPM400: Not Present
Oct 20 15:20:55 redbox-ast16 kernel: VPM450: Not Present
Oct 20...
2006 Mar 14
0
help required configuring card
...l => 1-24
Click on update and click on reload the configuration.
** here I?m facing the problem as we have two port card installed in the machine what are the entries we need to put in this file zapata.conf .
4.Then go back to asterisk@home console and give following commands
modprobe wct2xxp [ This is for Digium TE205P card]
ztcfg ?vv to see the status.
Once this is done we have to make configuration through the web console.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060314/8e3df...
2009 Feb 18
0
connection to siemens hipath
...0 IO-APIC-edge rtc
9: 0 0 IO-APIC-level acpi
12: 133 0 IO-APIC-edge i8042
14: 39 0 IO-APIC-edge ide0
50: 7629 2403996 IO-APIC-level uhci_hcd:usb1,
ehci_hcd:usb4, libata
66: 9326 92941584 IO-APIC-level wct2xxp
169: 294 1012573 IO-APIC-level eth0
177: 0 0 IO-APIC-level uhci_hcd:usb2
185: 0 0 IO-APIC-level uhci_hcd:usb3
NMI: 3066 4650
LOC: 91316250 91316178
ERR: 0
MIS: 0
----------------------------- chan_dahdi.c
[ch...
2010 Jul 12
0
DTFM Detection issues
...enter spanconfig!
[ 17.687422] Done with spanconfig!
[ 17.687422] About to enter spanconfig!
[ 17.687422] Done with spanconfig!
[ 17.687422] dahdi: Registered tone zone 6 (Spain)
[ 17.687422] About to enter startup!
[ 17.687422] TE2XXP: Span 1 configured for CCS/HDB3/CRC4
[ 17.687422] wct2xxp: Setting yellow alarm on span 1
[ 17.687422] timing source auto card 0!
[ 17.687422] SPAN 1: Primary Sync Source
[ 17.687422] timing source auto card 0!
[ 17.699422] VPM400: Not Present
[ 17.719825] firmware: requesting dahdi-fw-oct6114-064.bin
[ 17.731424] VPM450: echo cancellation for...
2007 Feb 19
1
Problems with CentOS ztdummy kernel 2.6
...amp;& /sbin/depmod -a 2.6.9-42.0.3.ELsmp || :
[ -f /etc/zaptel.conf ] || install -D -m 644 zaptel.conf.sample
/etc/zaptel.conf
build_tools/genmodconf linux26 "" "tor2 torisa wcusb wcfxo wctdm wctdm24xxp
ztdynamic ztd-eth wct1xxp wcte11xp pciradio ztd-loc wct4xxp wcfxs wctdm8xxp
wct2xxp"
Building /etc/modprobe.conf...
Once it is installed I run: modprobe ztdummy with the following result.
FATAL: Module ztdummy not found.
FATAL: Error running install command for ztdummy
--
Chris Blunt
Entropy IT Ltd
-------------- next part --------------
An HTML attac...
2010 Jun 17
1
DTMF detection issues
...enter spanconfig!
[ 17.687422] Done with spanconfig!
[ 17.687422] About to enter spanconfig!
[ 17.687422] Done with spanconfig!
[ 17.687422] dahdi: Registered tone zone 6 (Spain)
[ 17.687422] About to enter startup!
[ 17.687422] TE2XXP: Span 1 configured for CCS/HDB3/CRC4
[ 17.687422] wct2xxp: Setting yellow alarm on span 1
[ 17.687422] timing source auto card 0!
[ 17.687422] SPAN 1: Primary Sync Source
[ 17.687422] timing source auto card 0!
[ 17.699422] VPM400: Not Present
[ 17.719825] firmware: requesting dahdi-fw-oct6114-064.bin
[ 17.731424] VPM450: echo cancellation for...
2010 Nov 02
0
Noise while passing channel using tde205p card
...S},1)
exten => s-BUSY,1,Goto(jump2,s,1)
exten => s-NOANSWER,1,Goto(jump2,s,1)
exten => s-CHANUNAVAIL,1,Goto(jump2,s,1)
exten => s-CONGESTION,1,Goto(jump2,s,1)
[jump2]
...
####################################################
/proc/interrupts
201: 1339458395 337993774 IO-APIC-level wct2xxp
####################################################
lsmod
Module Size Used by
xpp 135236 0
wct4xxp 400384 62
zaptel 190852 132 xpp,wct4xxp
Note: I guess that mismatch between wct2xxp (device name) and wct4xxp
(driver name), i...
2006 Feb 19
1
[slackware 10.2 and TE205P] Unknown signalling method 'pri_cpe'
...because it's my favourite distro and it is
still suggested here
http://www.voip-info.org/wiki-Asterisk+Linux+Slackware)
, so, i've installed the last 10.2 release, and i've recompiled the
2.6.15.4 kernel.
then i've downloaded asterisk1.2.4 and zaptel1.2.4
i load module zaptel and wct2xxp (i've got a TE205P)
this is my lsmod:
root@asterisk:/data/programmi/asterisk1.2.4/asterisk-1.2.4# lsmod
Module Size Used by
wct4xxp 106048 -
zaptel 222948 -
and this are the channel in
root@asterisk:~# cat /proc/zaptel/1
Span 1: TE2/0/1 "T...