search for: wanpipemon

...roblem with a sangoma A104 card, I just installed to replace a Digium TE410 card, that was acting up. But now we have a problem with the sangoma card. It runs great after being started, and calls proceed as normal, but after about 1 hour, it stops being able to make and receive calls. If I run wanpipemon debug, can see that the card still receives packets from the ISDN, but when I make a call, I cant see it in wanpipemon, and asterisk just responds with a: NOTICE[17240] app_dial.c: Unable to create channel of type 'Zap' (cause 34 - Circuit/channel congestion) I am pretty shure that th...

...i2, qsig, and now dms100 for the switchtype. The telco tech I've been working with says that he's been sending "reset all channels" signals to my system, to which he's getting an "establish remote" response from my asterisk box. I've been running a packet dump (wanpipemon -i w1g1 -c trd) of my d-channel this whole time and have yet to see a single incoming packet. I believe I *should* be seeing an incoming packet when he sends the reset, correct? Is there any way to do a completely raw dump of the d-channel? Here are my specs: linux-2.6.16 libpri-1.3.5 zaptel-1.2...

...in this list that were not actually active anymore. They go away if I restart asterisk, but in the meantime channel use appears artificially inflated. I am wondering if there is a better method, perhaps with Sangoma CLI tools, to show which channels are ACTUALLY in use? I played around with wanpipemon but that doesn't really give channel specific info. Any clues? I posted on the Sangoma forums also... Thanks! j

...call them now, but it's Sunday morning in the sticks, and my chances of getting someone with a clue are slim to none. I restarted dahdi but that had no effect. I watched dahdi_tool as calls came in and out but there isn't really a lot of information there. Sangoma has a cool tool "wanpipemon" that shows error stats and such on the span. Is there such a tool for Digium cards? Any suggestions? Thanks, -- Jeff LaCoursiere SunFone jeff at sunfone.com

...d | wanpipe4 | AFT TE1 | N/A | Disconnected | wanpipe5 | AFT TE1 | N/A | Disconnected | wanpipe6 | AFT TE1 | N/A | Disconnected | wanpipe7 | AFT TE1 | N/A | Disconnected | wanpipe8 | AFT TE1 | N/A | Disconnected | root at Sangoma-Testing:/etc/asterisk# wanpipemon -i w1g1 -c Ta ***** w1g1: E1 Alarms (Framer) ***** ALOS: OFF | LOS: OFF RED: OFF | AIS: OFF OOF: OFF | RAI: OFF ***** w1g1: E1 Alarms (LIU) ***** Short Circuit: OFF Open Circuit: OFF Loss of Signal: OFF ***** w1g1: E1 Performance Monitoring Counters *****...

Hi all, Does Asterisk contain a full fledged ISDN packet sniffer. By giving the command " pri intense debug span 1 " , does it debug every packet received (control and voice/data packets) ? Thanks -- Arpit Mehta Graduate Student Department of Computer Science Columbia University Tel: 1-646-387-5998

...an call with an outside destination from Asterisk to the Toshiba. The Toshiba is looking for 9 to grab an outside line then it expects to see the 10 digits. In the FreePBX dial plan I use 9|. which sends 9 plus the 10 digit number. Using Wireshark to look at the QSIG commands coming from a Sangoma wanpipemon trace I see the following for an Asterisk to Toshiba internal call. Asterisk -> SETUP Toshiba -> CALL PROCESSING Toshiba -> CONNECT Asterisk -> CONNECT ACKNOWLEDGE However when trying to dial 9 + number I received the following Asterisk -> SETUP Toshiba -> SETUP ACKNOWLEDGE Lo...

...us" shows disconnected. Following are the alarms raised. Should I call telco (they have long wait times) or should I just keep searching online for troubleshooting tips. "*wanpipe1 | AFT TE1 | N/A | Disconnected |" <<<<<* This is what shows. root at pbx:~ $ wanpipemon -i w1g1 -c Ta ***** w1g1: T1 Rx Alarms (Framer) ***** *ALOS: OFF | LOS: ON* *RED: ON | AIS: OFF* *LOF: ON | RAI: OFF* * * ****** w1g1: T1 Rx Alarms (LIU) ****** * * *Short Circuit: OFF* *Open Circuit: OFF* *Loss of Signal: ON* ***** w1g1: T1 Tx Alarms ***** AIS: O...

...bout hardware failure, so we built a new box and installed 1.8.24.0, Dahdi 2.7.0.1, and a new Sangoma A104D. The single active span is an RBS T1 B8ZS/ESF/E&M Wink. I tried to move one span over one night which was working fine on the old box. Once plugged in there were no alarms, Sangoma wanpipemon utility showed "connected". I tried calling in on a DID number, and in the 'full' log, with debug and verbose set to 100: [Dec 5 00:51:37] VERBOSE[5283] sig_analog.c: -- Starting simple switch on 'DAHDI/9-1' [Dec 5 00:51:38] DEBUG[5283] dsp.c: tone 1100, Ew=1.17...

Hi All, I am looking for a way to troubleshoot issues with TDM (E1) trunks with a provider. Currently with SIP trunks I am using tcpdump to perform packet captures between our gateways and the SIP providers IPs, capturing traffic on all ports, to include both the SIP messages and the RTP stream. How can I achieve a similar result on TDM links connected to TDM cards in Asterisk servers, where by

Hey all, I had a user complaining of calls which were dropping mid-conversation. I looked into the time of one of the calls, and saw the following: Apr 4 12:13:03 WARNING[6670] chan_zap.c: No D-channels available! Using Primary channel 28 as D-channel anyway! Apr 4 12:13:05 WARNING[6660] channel.c: Avoided initial deadlock for '0x82b8430', 10 retries! Apr 4 12:13:05 WARNING[6660]

Hi all, My problem boils down to these errors: ... Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion) == Everyone is busy/congested at this time This is triggered by lines in extentions.conf such as: exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W) The system is CentOS v5.2 with Asterisk 1.4.23 (druid-asterisk-1.4.23.1-2), a Sangoma A104