search for: telewest

...(type 2 and 3 I believe in Oftel terms), but I'd accept just our DDI if that was all I could get. Steve -----Original Message----- From: Storer, Darren [mailto:starusers@comgate.tv] Sent: 01 July 2004 09:35 To: asterisk-users@lists.digium.com Subject: RE: [Asterisk-Users] Providing Telewest in the UK with per extension outbound callerID Hi Steve, SH> Is anybody in the UK using Telewest as a PRI Telco provider? SH> Are you sending them caller ID? Just a quick point of clarification before commenting further, do you wish to make calls via Telewest's network and se...

A client used to use BT isdn30 and ported the numbers to telewest several years ago. Now, the client moved to adept telecom. I *think* adept resells BT products. We got new numbers from adept (bt?) and the old pbx on the telewest lines forwards the calls to the new numbers. On the adept line I got a digium card in an opteron supermicro server. ztcfg gives me over...

Hi, Is anybody in the UK using Telewest as a PRI Telco provider? Are you sending them caller ID? I've been told by Telewest that:- 1. Oftel doesn't allow them to accept caller ID (this is rubbish, and I replied pointing out where in the link to Oftel that they sent me it was stated. We need Type 2 caller ID) 2. Telew...

Folks, I've seen a few reports that people have had problems with hang up detection on UK cable phone lines. I have a TDM400P with two FXO ports, one connected to my BT line and the other connected to my Telewest/Virgin Media cable line. If I ring the BT line and then clear down, Asterisk detects this and acts accordingly. If I ring the Telewest line, the clear down is not detected, hence Asterisk continues to ring extentions, record voicemail, etc. I've seen a few posts reporting this issue with the...

Hi, ? I'm trying to figure out what the issue is splicing Asterisk between our Telewest PRI and a GDK-186 with a PRI card. ? We're using the Digium TE405P ? Our telco provider is Telewest, and Telco directly into switch is fine. ? When I splice Asterisk in, I can make and receive calls from Asterisk extensions, I can make outbound calls from the GDK, but inbound calls do not seem...

Skipped content of type multipart/alternative

Hi there, We've got a problem connecting Asterisk with a TE205P to a TeleWest E1 ISDN line in the UK. We get a lot of "HDLC Bad FCS (8) on Primary D-channel" errors, and every so often the Primary D-channel goes down and all the calls got dropped. We've fully tested the card and made sure it's got its own IRQ. I was just wondering if anyone...

...someone can point me in the right direction. current spec I am using (Trixbox 1.0 was still in beta at the time an didn't detect the TE110 card, and modules didn't load properly when I tried manually either ) Asterisk@home 2.8 Wildcard TE110P ISDN PRI card (set to E1, I live in the UK) Telewest Q931 ISDN connection (currently 8 lines 100 phone numbers) dell SC1425 server (3.2 Ghz, 512MB, 80GB) SIP phones aastra 9133i run 1.4.0 firmware. This is on a live system with about 50 users. (I have a identical system for DR so can easily test out of hours) Most the time there is no echo, If I p...

Hi I posted earlier about having issues connecting to Telewest's ISDN, only to find out later Telewest had forgotten to turn it on - hopefully I'm not having a similar silly problem. My PRI span is now up and operational, but when I try to send a call out over it, I just get congestion tones. Occasionally, I get about one second of ring tones, only fo...

...someone can point me in the right direction. current spec I am using (Trixbox 1.0 was still in beta at the time an didn't detect the TE110 card, and modules didn't load properly when I tried manually either ) Asterisk@home 2.8 Wildcard TE110P ISDN PRI card (set to E1, I live in the UK) Telewest Q931 ISDN connection (currently 8 lines 100 phone numbers) dell SC1425 server (3.2 Ghz, 512MB, 80GB) SIP phones aastra 9133i run 1.4.0 firmware. This is on a live system with about 50 users. (I have a identical system for DR so can easily test out of hours) Most the time there is no echo, If I p...

Hi, I'm trying to connect to Telewest/Virgin Media with a TE110P using asterisk 1.4.13/zaptel 1.4.6. No matter what I try, my span always appears as PRI span 1/0: Provisioned, Down, Active My zapata.conf is currently ----------------------------------- [channels] echocancel=yes echocancelwhenbridged=no echotraining=yes switchtype=eur...

I am on UK Cable (Telewest) will this callerid patch work with the cable caller id? Thanks. Paul.

Hi all, I have an issue with my system and the phone company (Alltel). If someone goes into any mailbox on the server to leave a message, once they hang up on their side the system is not detecting this and will sit there and record until you get the standard message from the phone company "If you'd like to make a call, please hangup and try again", which is preceded by the fast

Hi, Built a new server at the weekend and install Asterisk 1.6.0.9 and IAX and SIP work great :) The one problem I am having is getting the OpenVox (TDM400 type card) to work. It is successfully identified using WCTDM kernel module and dahdi_scan picks it up just fine. The issue is when I try and setup dahdi_channel.conf as it fails everytime. When running asterisk -rvvvv I see the port pick

...e a problem calling a certain number from our PRI line. Calling the number from a separate PSTN phone works fine. The remote number seems to have some funny call redivert setup, when you call it, it answers immediately, makes some kind of beep and then starts to ring. Our PRI is in the UK from Telewest/NTL/Virgin Media and most outgoing calls work without a problem. The server is trixbox based with a Digium TE410P PRI interface. Trixbox 2.6, Asterisk 1.4.18-3, FreeBPX 2.4. I'm no expert, but the PRI trace shows that the outgoing call is proceeding, and then seems to show that my end of th...

Hi all, I've finally taken the plunge and had isdn installed. It's a BRI from Telewest in the UK. I'm told by the provider that it's in point to multipoint mode with 6 digit presentation. I'm using an AVM fritz (bt speedway) with the fcpci-suse9.1-3.11-02 driver. Chan_capi seems to be installed fine. I can receive incoming calls. However, I can't call out. When ever...

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: AbdelRahman el Tarzi.vcf Type: text/x-vcard Size: 4042 bytes Desc: not available Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20060305/7d9e5777/AbdelRahmanelTarzi.vcf

...quiet line test anyway - with a background hiss and ticking) So it's still a bit of a mistery! > The other problem I have is reliable CLID, sangoma and Myphonecall have been > very helpful but still no 100% fix :( I seem to get CID through OK on BT lines. I'm still battling with a Telewest line though, but I've a feeling theyuse Bell signalling. What annoys me is that a bog-standard DECT phone with CID diaply works perfectly on either a BT or Teleworst line, but the * box fails to see anything other than a BT line.. I'm also using a GSM <-> analog gateway box, which...

I've just installed an X100P, built the kernel module, and tried to use it to make an outgoing call (via a phone connected to an ATA-186). However, I just get a reorder tone and see this on the console: -- Executing Dial("SIP/ata1-4409", "Zap/1/5551212") in new stack NOTICE[1200825920]: File app_dial.c, Line 481 (dial_exec): Unable to create channel of type

Hi, got a Sangoma A200 with a bunch of extension cards and having real problems getting it to deal with a normal single BT line Symptoms are that incoming calls are fine. Outgoing calls ring the far end, BUT asterisk never sees that the call is answered (ie no message in the logs files saying so), as a result the remove end can hear the PBX side talking, but there is no audio back from the