search for: te100p

Hello, i've googled and can't find a definite answer, so here goes: I have purchased the Digium TE100P, and am setting up the connection, however the telco i'm supposed to work with does not support PRI/ISDN E1 connections. They only support E1/R2 lines. Is there a way i can make the TE100P work with this? I've not seen any zaptel.conf that supports this. Any workarounds? Thanks for any...

Hi, I have a Gateway running in "TE" (terminal equipment mode as "slave" that I need to connect to my asterisk server using a TE100P card. Can anybody give a quick run up of how to run the TE100P's in Network Termination mode to have this working sucessfully? Cheers! Regards, Sahil Gupta VoiceValley

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel...

...inal Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Kerry Garrison Sent: Tuesday, May 02, 2006 10:51 AM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: RE: [Asterisk-Users] Need help configuring TE100P and 3 X100Pclonewith MD3200 chipset Are you seriously trying to run 4 cards in one system? The odds of getting that working are about the odds of Angelina Jolie showing up on my doorstep ready to whisk me off to....but I digress...you will have serious interrupt issues trying to get 4 cardss worki...

Hi, I have a problem I will describe. I have PAP2 connected to the internet to an asterisk box with 2 TDM cards, one TE100P E1 with PRI and one TDM400P with 2 FXS an one FXO. When I call to the TDM400 cards from the PAP2 eveything is OK, sound quality is perfect. When I call to terminate the call in PSTN through E100P I hear clicks which aparently are RTP packet looses. This clicks are only heard in the PSTN side, not...

...-Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of steve@daviesfam.org Sent: Tuesday, May 02, 2006 10:54 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Need help configuring TE100P and 3 X100P clonewith MD3200 chipset On Tue, 2 May 2006, Wai Wu wrote: > [root@asterix root]# modprobe zaptel > [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on > channel 25: No such device or address (6) > /lib/modules/2.4.20-8/misc/wcte11xp.o: post-install wcte11xp...

Hi everybody, I managed to install card over Suse 9.2, I substituted Zaptel drivers and compiled them. Now "ztcfg" says I have one card with correctly configured 31 channels, but red led on back of card doesn't flash. Suse 9.2 has detected the card as a Tiger Jet card, since the chip on it is a Tiger 320. The second card configuration is still waiting for configuration, but I think

Hey guys, I've been struggling with hangup detection on a Centrex system for a bit now, I was on site Saturday and I took my DMM with me. It would appear that this Centrex service provider uses polarity reversal at the beginning of a call and several times after hangup. I've been reading the archives for the last year and it looks like there was some work done that matches my

Guys. I have a te100p with unicall and an E1 and Im having problem with DTMF tones but the weird thing is, I only have problems sending the tones to certain phone numbers, anybody seen this behavior? Asterisk shows on the console the dtmf tone been pressed but seems the other side is not getting them, and this just hap...

...nnel bank. Since the X101P isn't approved, and doesn't appear to be approved soon, the chances of getting a Australian approved channel bank at a decent price is likely low. Again, with smaller offices (say 15 or less extensions) the price of a TE400P card is too expensive, will there be a TE100P card produced and approved for use in Australia? Even if it is, will this solve the problem? I'm thinking not, because the single port would need to connect to a channel bank which in turn would connect to the telco plus extensions, therefore we are back to the same situation as with analog lin...

...extension is executed and dial the extension of the HT486 device (firmware 1.0.5.22). Somehow sending fax out working well. In the mailing lists, i notice some are using HT286 and it work. Could someone share theirs experience and give some help? E1 PSTN ----------> Asterisk (TE100P) --------> HT486 ----> Fax machine zapata.conf [channel] context=Local switchtype=euroisdn signalling=pri_cpe rxwink=300 callwaiting=yes usecallingpres=yes; callwaitingcallerid=yes echocancel=yes echocancelwhenbridged=yes echotraining=yes echotraining=400 rxgain=0.0 txgain=0.0 immediate=no...

Hello, I am having some problems with faxing in asterisk. I have a TE100P which is taking my PRI. This seems to be working fine. I also have a TDM400P with 2 FXS. Again card seems to be working fine, I can dial from phones attached to these to ports and everything seems to work fine. I have 2 DID's for my two fax machines that dial the Zap port for the FXS on the...

I have connected asterisk 1.0.7 with Avaya Definity via E1 with a TE100P Digium Card. Inbound calls are working perfectly and I dont have any problem. But when I try to make an outgoing call with my softphone (xlite) I am getting the following messages. Hungup 'Zap/13-1' Executing Dial("SIP/IZ-bc0a", "Zap/g1/3118") in new stack Called g1/311...

..., it shouldn't be any real effort or even delay if you >want to add more circuits. From the switch side they just turn up a few >more DS0's and you coordinate to configure your side as well. No real >circuits have to be wired and no new equipment to add. Not to mention a >single TE100P card at $500 is cheaper than 2 TDM400 cards fully kitted >out. >-- -- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.290 / Virus Database: 265.6.7 - Release Date: 12/30/2004

Hi. I have a problem with two asterisk servers with version 1.2.5. In one server there is a Digium TE411P in the second the Digium TE100P. We use E1 and EuroISDN. '/etc/zaptel.conf': ----- begin ----- span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 ----- end ----- /etc/asterisk/zapata.conf': ----- begin ----- [channels] pridialplan = unknown prilocaldialplan = international localprefix = 0512 nationalprefix = 0 inte...

I have connected asterisk 1.0.7 with Avaya Definity via E1 with a TE100P Digium Card. Inbound calls are working perfectly and I dont have any problem. But when I try to make an outgoing call with my softphone (xlite) I am getting the following messages. Hungup 'Zap/13-1' Executing Dial("SIP/IZ-bc0a", "Zap/g1/3118") in new stack Called g1/311...

First encounter with * Just downloaded & installed aah-2.7 Started up AMP, but i can not find any reference towards isdn. I presume there has to be some configuration done for my Eicon-Diva-pro. Does aah actually support isdn-bri? On the mail-archive i found some references, but these are rather old ( they speak about the coming release of aah-2.1) aah-handbook (version 1.6) doesn't

We have a TE110P (single span PRI) and are having tons of echo on all calls, both incoming and outgoing. We didn't have any echo at all yesterday and nothing in any of the configs has changed. All of all calls follow this pattern: Cisco 7960 -> Asterisk -> PRI Here is my zapata.conf [channels] context=all-incomming switchtype=national resetinterval = 3600 priindication =

Hi all, I have this project that requires me to use 8 PSTN lines and possible more. I was thinking 2 TDM cards with FXO modules. The I got to read the "Qs about FXO/FXS cards" thread and that scared me. Can anybody recommend anything that is known to work ok with no mysterious problems? I was thinking OpenSwitch12 cards. What do you guys think? Any help is appreciated. Regards, Hadi

Hi, I have to connect 30 phone lines to my asterisk server, can somebody help on how I have to do it ? I have a TDM405P and one TDM400P with 4 FXO ports. Do I have to use 8 TDM400P ? Or, is there another way to do it ? Thanks, Angel.