search for: rtl8169

Motherboard - Intel DG41TY Device: RealTek: 8111D Driver: RTL8169 Causes Kernel panic during install and boot. -- It seems that the newer the card that uses this driver, the worse the problems are. Is there any plan to roll a newer version into the installer or the actual distribution itself? Thanks, -Drew -------------- next part -------------- An HTML attach...

I installed 5.2 x86_64 on a new hp dv7z laptop using noprobe on the install line. After rebooting the rtl8169 causes the kernel to dump. Is there a parameter I can pass to it (somehow) to avoid the kernel dump??? Thanks, Jerry

Hi. I have 2 PC's connected with 1GBit NIC's. When I transfer a file from my File-Server(Redhat9.0, 256 SD-RAM, 300MHz PII, RTL8169 NIC, 2x Western Digital WD200JB RAID 0) to my Windows-PC(AMD Athlon XP 1800+, 1024 MB DDR-RAM, WINXP PRO, RTL8169 NIC, 2x Western Digital WD080JB RAID 0) with Samba, i get Speeds around 8-9MB/sec. I think this is too low for an GBit Network, so i tested the NIC's with the Tool Iperf (http://das...

I am trying to install 5.2 on a new dv7z hp laptop. I use "linux noapic nolapic iommu=off " and I get a kernel dump on rtl8169. I dont need the network to install? how do I ignore the rtl8169 to install. I tried noprobe and then it doesnt recognize my SATA HD controller and I dont know yet which driver to select as I cant do an lspci to see??? THanks, Jerry

...39;Realtek Semiconductor' device = 'RTL8168/8111 PCI-E Gigabit Ethernet NIC' class = network subclass = ethernet re0@pci0:2:4:0: class=0x020000 card=0x10ec16f3 chip=0x816710ec rev=0x10 hdr=0x00 vendor = 'Realtek Semiconductor' device = 'RTL8169/8110 Family Gigabit Ethernet NIC' class = network subclass = ethernet re1@pci0:2:6:0: class=0x020000 card=0x10ec16f3 chip=0x816710ec rev=0x10 hdr=0x00 vendor = 'Realtek Semiconductor' device = 'RTL8169/8110 Family Gigabit Ethernet NIC' class...

...> > > > >Best Regards, > >Richard M at Technical Support > >USR Technical Support > >----------------------- > >Trying to install driver. README file says to unzip > >98169_linuxdrv_vxx.zip, which is supposed to contain the Linux kernel > >driver RTL8169. CD that came with this Gigabit Ethernet PCI Adapter does > >not have this file. Google the Net does not turn it up. Searching your > >site does not turn it up. Simply running the make, anyway (after copying > >the files that are present to my SUSE 9.3 box) only gives the erro...

...#39;m trying to get my network setup as streamlined as possible. I ran a brain-dead-simple speed test of Samba and I'm very confused by the results. Here's my setup: Fast new WinXP Pro machine NetGear GA311 gigabit ethernet ^ | dedicated gigabit ethernet line (no switch) v RTL8169 gigabit ethernet Relatively fast new Debian Linux machine I set up ramdisks on both machines to ensure that the hard drives were not the bottleneck. I then put a roughly 7 MB file on the linux ramdisk and mounted that disk on my windows box via Samba. I then wrote a .bat script on the windows...

is it possible to crete a domu without network support hello users, Myself Dharma, new to xen,              i am trying to create a domu .I have realtek 8168SC gigabit ethernet card which is not supported by xen.it has support for rtl8169 only. is it possible to create domu without network support while i am trying to create it getting error :2049 device not found hotplug scripts missing Any help please DISCLAIMER: ------------------------------------------------------------------------------------------------------------------...

Hi all, I've recently upgraded a system from CentOS 4.4 to CentOS5, and now when the system boots, the r8169 ethernet card doesn't come up. After the boot sequence, if I type "ifup eth1 | ifup eth1.10 | ifup eth1.203" then the adapter starts up ok. It seems to be something with the boot sequence it loads the ethernet adapters a different way around (ie 4.4 eth0 is now

...ny amount > of debugging, the thing is I don't know what to look for. > > > Anand Linus is right, this is probably a memory leak issue. There are several areas that could be the problem: - core networking - iptables - iptables filter - ethernet bridging - ethernet driver (rtl8169) To find/fix the problem, we need to narrow down the scope. Things that would help are, what are the iptables rules you are using? Are there any errors showing up on the ethernet devices? Also what does the bridge forwarding table look like? are there lots of entries, are you running spanning tr...

Hi! I?m having trubbles with the speed on my samba server, I just uppgraded to gigabit (Realtek 8169 NIC) at home when i copy stuff from the samba server i get around 5-6Mb/sec and if i use ftp to access the same file on the same server i get almost 30Mb/sec does anyone have a clue what causes this problem? When i used my old 3com 905c for the local net i got normal 100Mbit speed (around

...tos.org/pipermail/centos/2007-February/075383.html I'm guessing this would go in the HardwareList section. Otherwise a page titled 'Realtek r1000 Driver' would work. my wiki username is kirkbocek. Thanks, Kirk Bocek Chipsets listed by Realtek: RTL8110SC(L) RTL8110S-32 RTL8110SB(L) RTL8169SB(L) RTL8169SC(L) RTL8169

Hi all, I've just upgraded my home network to a Linksys SRW2024 (with lovely vlan trunking support!) and I'm trying to enable jumbo frames. When I try to set the MTU of an rtl8169 based network card (it's a Netgear RA311), it comes up with an error stating: # ifconfig eth1 mtu 9000 SIOCSIFMTU: Invalid argument The only options it will take are 1500 or below. Does anyone know anything about this? Do I need to set something special? -- Steven Haigh Email: netwiz at...

...s: [dc] Power Management version 2 Once I compiled and installed the r1000 on kernel 2.6.9-42.0.8, loading the driver yielded: eth1: Identified chip type is 'RTL8110SC'. eth1: r10001.05, the Linux device driver for Realtek Ethernet Controllers at 0xde00, 00:e0:4d:04:e8:c3, IRQ 209 Realtek RTL8169/8110 Family Gigabit Ethernet Network Adapter Driver version:1.05 Released date:2006/10/25 I checked another host that has a more recent 2.6.18.6 kernel and confirmed that it does *not* have the r1000. So I guess the r1000 isn't part of the kernel yet. You can get the r1000 at: http://www.rea...

Remote box SNV93 (xVM kernel) 192.168.1.54 (NIC RTL8169) Attempts of ssh connection from CentOS 5.1 DomU 192.168.1.37 at SNV93 Dom0 (NIC RTL8110SC) # ssh user1@192.168.1.54 hangs .. TCPDUMP running on remote box (192.168.1.54) # tcdump -s 1600 -vv One entry generates for each ssh connection attempt. First:- 17:12:43.058821 IP (tos 0x0, ttl 64, id 1977...

Hi, I've been testing the Debian packages ahead of the Debian 7 release (which is very imminent) I believe this is a serious bug[1] in the package, as it appears that HVM networking is broken, or at the very least, requires some undocumented configuration step Specifically: - I can start the HVM domU without any vif - if I attach a vif, the domU will not start Looking at

Hi, I''m trying to install xen with this configuration: dom0 -> Centos 5.3 dom1 -> Fedora 10 dom2 -> Fedora 10 Centos kernel = (2.6.18-128.1.10.el5.centos.plusxen) XEN Version = 3.0.3 I''m having some problems trying to install xen on my mychine, but i''ve been able to solve all of them but one: i can''t reach my gateway from

...o sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 152k freed r8169 Gigabit Ethernet driver 2.2LK loaded GSI 19 sharing vector 0xC1 and IRQ 19 ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 16 (level, low) -> IRQ 19 eth0: Identified chip type is ''RTL8169s/8110s''. eth0: RTL8169 at 0xffffc20000040f00, 00:0c:76:b3:3d:7e, IRQ 19 ReiserFS: dm-1: found reiserfs format "3.6" with standard journal ReiserFS: dm-1: using ordered data mode ReiserFS: dm-1: journal params: device dm-1, size 8192, journal first block 18, max trans len 1024, ma...

Seems like overnight every motherboard that worked with linux has DROPPED off the face of the earth. Every motherboard I looked at is using the realtek 8111 chipset and a northbridge that is not supported. Example: GIGABYTE GA-970A-DS3, does not work with linux I tried disabling the onboard NIC and using a PCI-E intel card I always use and that would not work either. The north or south bridge

Hi there, I''m using the Suse Enterprise 10 RC2 along with Xen 3.0.2 on X86-64 and I''m experiencing a problem with the network. I boot into the Xen kernel and everything works just fine. I can browse the net etc. However after a while the network stops responding completely. I am not sure what causes this to happen or what triggers it. After a few hours, the network just stops