search for: portonvictor

...lp to eliminate this buggy behavior. Shall we consider this very message as a bug report, or should I report a bug otherwise somewhere? My /etc/nut/ups.conf : maxretry = 3 [advice] driver = blazer_usb port = /dev/ttyS0 vendorid = 0665 productid = 5161 -- Victor Porton - http://portonvictor.org

...very message as a bug report, or should I report a bug otherwise somewhere? > > My /etc/nut/ups.conf : > > maxretry = 3 > > [advice] > ????driver = blazer_usb > ????port = /dev/ttyS0 > ????vendorid = 0665 > ????productid = 5161 > > -- > Victor Porton - http://portonvictor.org > > _______________________________________________ > Nut-upsuser mailing list > Nut-upsuser at lists.alioth.debian.org > http://lists.alioth.debian.org/cgi-bin/mailman/listinfo/nut-upsuser -- Victor Porton - http://portonvictor.org

...wise somewhere? >> >> ?My /etc/nut/ups.conf : >> >> ?maxretry = 3 >> >> ?[advice] >> ?????driver = blazer_usb >> ?????port = /dev/ttyS0 >> ?????vendorid = 0665 >> ?????productid = 5161 >> >> ?-- >> ?Victor Porton - http://portonvictor.org >> >> ?_______________________________________________ >> ?Nut-upsuser mailing list >> ?Nut-upsuser at lists.alioth.debian.org >> ?http://lists.alioth.debian.org/cgi-bin/mailman/listinfo/nut-upsuser > > -- > Victor Porton - http://portonvictor.org > &gt...

...-u <username> set username for command authentication -p <password> set password for command authentication <ups> UPS identifier - <upsname>[@<hostname>[:<port>]] Call without -s to show all possible read/write variables. -- Victor Porton - http://portonvictor.org

...s and the protocol, do I need to adjust time and/or percentage parameters, to be sure my computer will be turned off automatically after a reasonable time after failing electricity? My UPS is Advice PRS850. If I need to adjust the parameters, please explain the details. -- Victor Porton - http://portonvictor.org

...input.voltage: 234.9 input.voltage.fault: 234.9 input.voltage.nominal: 230 output.voltage: 234.9 ups.beeper.status: enabled ups.delay.shutdown: 30 ups.delay.start: 180 ups.load: 18 ups.productid: 5161 ups.status: OL ups.type: offline / line interactive ups.vendorid: 0665 -- Victor Porton - http://portonvictor.org

On Dec 1, 2014, at 4:11 AM, Victor Porton <porton at narod.ru> wrote: > battery.voltage: 13.70 > battery.voltage.high: 13.00 > battery.voltage.low: 10.40 These are the voltage thresholds for the UPS, so theoretically the UPS will send the LB signal when the battery voltage goes lower than 10.40 Volts. Also, if battery.charge works, you can use "ignorelb" if you want to

On Dec 1, 2014, at 9:19 AM, Victor Porton <porton at narod.ru> wrote: > 01.12.2014, 14:50, "Charles Lepple" <clepple at gmail.com>: >> Does "upsrw -l advice" show anything? > > $ upsrw -l advice > upsrw: invalid option -- 'l' I suppose I should read the documentation every once in a while :-) "upsrw advice" I was thinking of

...upsrw -l advice >> ?upsrw: invalid option -- 'l' > > I suppose I should read the documentation every once in a while :-) > > "upsrw advice" "upsrw advice" outputs nothing. > I was thinking of "upscmd -l advice". -- Victor Porton - http://portonvictor.org

On Nov 29, 2014, at 7:32 AM, Victor Porton <porton at narod.ru> wrote: > On Debian Linux jessie: > > After buying an UPS and installation of nut-server and nut-client at my PC and configuring the ports and the protocol, do I need to adjust time and/or percentage parameters, to be sure my computer will be turned off automatically after a reasonable time after failing electricity?

On Nov 25, 2014, at 8:17 PM, Victor Porton <porton at narod.ru> wrote: > Well, also below in dmesg: > > [ 190.249219] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33 rq 9 len 8 ret -110 -110 is -ETIMEDOUT. > 26.11.2014, 03:05, "Victor Porton" <porton at narod.ru>: >> A fragment of dmesg output (here idVendor=0665, idProduct=5161 is the